Analysis of Structural Transformations of Fe80Ni10Si5B5 Amorphous Alloy Based on Temperature Changes of Electrical Resistivity

2014 ◽  
Vol 1025-1026 ◽  
pp. 499-503
Author(s):  
Aleksandr Kotvitckii ◽  
Galina Kraynova ◽  
Anatoly Frolov ◽  
Vitaly Ivanov ◽  
Vladimir Plotnikov
Keyword(s):  
Electrical Resistivity ◽  
Amorphous Alloy ◽  
Structural Transformations ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Calorimetric Analysis ◽  
Temperature Changes ◽  
X Ray ◽  
Higher Temperature ◽  
Magnetic Nature

In this paper the change of electrical resistivity of the amorphous alloy Fe80Ni10Si5B5during heat treatment is investigated. Parallel studies by magnetometry technique, X-ray diffraction and calorimetric analysis were used to interpret the nature of the changes in the structure and properties of the alloy during annealing. These features are related with magnetic nature of the alloy and crystallization at a higher temperature.

Superconducting characteristics and the thermal stability of tungsten-based amorphous thin films

1992 ◽  
Vol 7 (4) ◽  
pp. 853-860 ◽  
Author(s):  
Seiichi Kondo
Keyword(s):  
Thin Films ◽  
Thermal Stability ◽  
Electrical Resistivity ◽  
Amorphous Alloy ◽  
Diffraction Analysis ◽  
Superconducting State ◽  
X Ray Diffraction ◽  
X Ray ◽  
Amorphous Thin Films ◽  
Thermal Stability Of

Superconducting characteristics and the thermal stability of sputtered, tungsten-based, amorphous thin films are investigated. Electronic properties and crystalline structures are analyzed as a function of the metalloid content in the films. It is well known that the superconducting Tc of a bulk crystalline tungsten is 0.01 K, which is one of the lowest transition temperatures among the superconducting metals. We have found that the W film containing 5 to 70 at. % metalloids exhibits a great enhancement in Tc. In the region of 15 to 35 at. % metalloids, the Tc shows the maximum of 5.0 K, and the transition from normal to superconducting state occurs very sharply. SEM observation together with x-ray diffraction analysis indicates that these films are amorphous in structure. The electrical resistivity is about 150 μΩ-cm, and shows little temperature dependence from Tc to 300 K. In addition, the W–Si amorphous superconductor is thermally very stable after annealing at 700 °C, but the W–Ge amorphous alloy crystallizes at 600 °C.

scholarly journals Impact of high temperatures on aluminoceladonite studied by Mössbauer, Raman, X-ray diffraction and X-ray photoelectron spectroscopy

2021 ◽  
Author(s):  
Mariola Kądziołka-Gaweł ◽  
Maria Czaja ◽  
Mateusz Dulski ◽  
Tomasz Krzykawski ◽  
Magdalena Szubka
Keyword(s):  
Photoelectron Spectroscopy ◽  
Integral Intensity ◽  
Photoelectron Spectra ◽  
X Ray Diffraction ◽  
Structural Reorganization ◽  
Oh Groups ◽  
X Ray ◽  
Al Content ◽  
Integral Intensity Ratio ◽  
Higher Temperature

AbstractMössbauer, Raman, X-ray diffraction and X-ray photoelectron spectroscopies were used to examine the effects of temperature on the structure of two aluminoceladonite samples. The process of oxidation of Fe2+ to Fe3+ ions started at about 350 °C for the sample richer in Al and at 300 °C for the sample somewhat lower Al-content. Mössbauer results show that this process may be associated with dehydroxylation or even initiate it. The first stage of dehydroxylation takes place at a temperature > 350 °C when the adjacent OH groups are replaced with a single residual oxygen atom. Up to ~500 °C, Fe ions do not migrate from cis-octahedra to trans-octahedra sites, but the coordination number of polyhedra changes from six to five. This temperature can be treated as the second stage of dehydroxylation. The temperature dependence on the integral intensity ratio between bands centered at ~590 and 705 cm−1 (I590/I705) clearly reflects the temperature at which six-coordinated polyhedra are transformed into five-coordinated polyhedra. X-ray photoelectron spectra obtained in the region of the Si2p, Al2p, Fe2p, K2p and O1s core levels, highlighted a route to identify the position of Si, Al, K and Fe cations in a structure of layered silicates with temperature. All the measurements show that the sample with a higher aluminum content and a lower iron content in octahedral sites starts to undergo a structural reorganization at a relatively higher temperature than the less aluminum-rich sample does. This suggests that iron may perform an important role in the initiation of the dehydroxylation of aluminoceladonites.

Sedimentary Clays as Geopolymer Precursor

2018 ◽  
Vol 39 ◽  
pp. 97-111
Author(s):  
F. Mostefa ◽  
Nasr Eddine Bouhamou ◽  
H.A. Mesbah ◽  
Salima Aggoun ◽  
D. Mekhatria
Keyword(s):  
Sodium Hydroxide ◽  
Mineralogical Composition ◽  
Cementitious Materials ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Calcination Time ◽  
Calorimetric Analysis ◽  
X Ray ◽  
Before And After ◽  
Mechanical Performances

This work aims to study the feasibility of making a geopolymer cement based on dredged sediments, from the Fergoug dam (Algeria) and to evaluate their construction potential particularly interesting in the field of special cementitious materials. These sediments due to their mineralogical composition as aluminosilicates; are materials that can be used after heat treatment. Sedimentary clays were characterized before and after calcination by X-ray diffraction, ATG / ATD, spectroscopy (FTIR) and XRF analysis. The calcination was carried out on the raw material sieved at 80 μm for a temperature of 750 ° C, for 3.4 and 5 hours. The reactivity of the calcined products was measured using isothermal calorimetric analysis (DSC) on pastes prepared by mixing an alkaline solution of sodium hydroxide (NaOH) 8 M in an amount allowing to have a Na / Al ratio close to 1 (1: 1). Also, cubic mortar samples were prepared with a ratio L / S: 0.8, sealed and cured for 24 hours at 60 ° C and then at room temperature until the day they were submited to mechanical testing. to check the extent of geopolymerization. The results obtained allowed to optimize the calcination time of 5 hours for a better reactivity of these sediments, and a concentration of 8M of sodium hydroxide and more suitable to have the best mechanical performances.

Study of Low-Grade Nickel Laterite Processing Using Palm Shell Charcoal as Reductant

2020 ◽  
Vol 1000 ◽  
pp. 436-446
Author(s):  
Bambang Suharno ◽  
Nolzha Primadha Ilman ◽  
Achmad Shofi ◽  
Deni Ferdian ◽  
Fajar Nurjaman
Keyword(s):  
Sodium Sulfate ◽  
Selective Reduction ◽  
Reduction Process ◽  
Low Grade ◽  
X Ray Diffraction ◽  
X Ray ◽  
Palm Shell ◽  
Higher Temperature ◽  
Nickel Grade

This study was conducted to investigate the effect of palm shell charcoal reductant in the selective reduction of nickel ore with the addition of additive at various temperatures and times. In this present work, 10 wt. % of sodium sulfate as additive and 5, 10, 15 wt. % of palm shell charcoal as reductants were used. The reduction of nickel ore was performed at 950oC, 1050oC, and 1150oC for 60, 90, and 120 minutes. A wet magnetic separation method was then carried out to separate the concentrates and tailings. Characterization of reduced ore was performed by X-Ray Diffraction (XRD) and Scanning Electron Microscope (SEM) with Energy Dispersive X-ray Spectroscopy (EDS), while the composition of ferronickel in concentrate was identified by X-Ray Fluorescence (XRF). The result showed that the higher temperature reduction, the higher of nickel grade, and its recovery at the concentrate. Nevertheless, the longer reduction time and the more reductant in nickel ore lowering the nickel grade and its recovery in the concentrate. The optimum condition in this selective reduction process was obtained with the addition of 5 wt. % of reductant and 10 wt. % of sodium sulfate in nickel ore, which was reduced at 1150oC for 60 minutes. It resulted in 4.60% and 73.23% for nickel grade and its recovery, respectively.

STUDY OF THE DEPENDENCE OF HIGH Tc ON VARIOUS SINTERING TEMPERATURES FOR Bi-Pb-Sr-Ca-Cu-O SUPERCONDUCTORS

1991 ◽  
Vol 05 (24n25) ◽  
pp. 1635-1638
Author(s):  
S.M. M.R. NAQVI ◽  
A.A. QIDWAI ◽  
S.M. ZIA-UL-HAQUE ◽  
FIROZ AHMAD ◽  
S.D.H. RIZVI ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Liquid Nitrogen ◽  
X Ray Diffraction ◽  
High Tc ◽  
X Ray ◽  
Resistivity Measurements ◽  
Zero Resistance

Bi1.7-Pb0.3-Sr2-Ca2-Cu3-Ox superconducting samples were prepared at 855°C, 862 C, 870 C, and 882 C sintering temperatures respectively. All samples were sintered for 120 hours. The samples were then quenched in liquid nitrogen. The electrical resistivity measurements showed that the samples sintered at 870° C had the best Tc. For these samples the Tc onset was around 120 K and the zero resistance was obtained at 108 K. X-ray diffraction studies showed that the samples were multiphased.

Crystal structures of highly stabilized ylides: methyl(3-methoxy,2-methoxycarbonylbenzoyl) triphenyl- phosphoranylideneacetate and methyl(2-methoxycarb-6-nitrobenzoyl)triphenyl phos phoranyl ideneacetate and the salt methyl(triphenylphosphoranylidene)acetate tetrafluoroborate

1998 ◽  
Vol 76 (12) ◽  
pp. 1844-1852
Author(s):  
Fernande D Rochon ◽  
Robert Melanson ◽  
Margaret M Kayser
Keyword(s):  
Key Words ◽  
Crystal Structures ◽  
Nitro Derivative ◽  
Transient Species ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ionic Salt ◽  
Higher Temperature ◽  
Cyclic Anhydrides ◽  
Wittig Reactions

At lower temperatures stabilized ylides react with unsymmetrically substituted phthalic anhydrides to give two acyclic adducts. When the reactions are allowed to proceed at higher temperature enol lactones are formed. Identification of the acyclic intermediates was necessary to understand the mechanism of these Wittig reactions. The transient species trapped in the reaction with trimethyloxonium tetrafluoroborate were unambiguously identified by crystallographic methods. The crystal structures of the tetrafluoroborate salt of methyl(triphenylphosphoranyl idene)- acetate (8), methyl(3-methoxy,2-methoxycarbonylbenzoyl)triphenylphosphoranylideneacetate (6β), and methyl(2-methoxycarbonyl,6-nitrobenzoyl)triphenylphosphoranylideneacetate (7α) were studied by X-ray diffraction. The ionic salt (8) is monoclinic, P21c,a= 12.640(5), b = 13.945(9), c = 14.825(6) Å, β = 125.32(3)°, Z = 4, and R = 0.065 (F >5.4 σ(F)). Crystal 6 β is monoclinic, P21c,a = 16.391(16), b = 9.029(6), c = 19.835(19) Å, β = 116.60(6)°, Z = 4, and R = 0.070 (F > 4.6 σ(F)), while crystal 7α is also monoclinic, P21c,a = 9.513(5), b = 9.361(3), c = 30.908(13) Å, β = 98.42(3)°, Z = 4, and R = 0.057 (F >5 σ(F)). In the BF 4- salt (12), the four P-C distances are equal (1.791(5)-1.801(7) Å) with identical tetrahedral angles. For the two triphenylphosphoranylideneacetate compounds, the fourth P-C(1) bond is shorter (1.762(6)-1.734(5) Å) than the three P-C(Ph) bonds (avg. 1.809(5) Å). The angles C(1)-P-C(Ph) are also larger (avg. 112.9(2)° for 6β and 111.9(2)° for 7α) than the C(Ph)-P-C(Ph) angles (avg. 105.8(2)° for 6 β and 106.9(2)° for 7α). These values suggest a multiple nature for the P-C(1) bond. In the nitro derivative, the nitro and the ester groups are disordered equally in positions 2 and 6. Key words: Wittig reactions, cyclic anhydrides, stabilized ylide, phosphoranylidenes, crystal structures.

Evolution of crystal structure of dual layered molecular conductor (ET)4ZnBr4(C6H4Cl2) with temperature

CrystEngComm ◽  
2021 ◽  
Author(s):  
Gennady V. Shilov ◽  
Elena I. Zhilyaeva ◽  
Sergey M. Aldoshin ◽  
Alexandra M Flakina ◽  
Rustem B. Lyubovskii ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Electrical Resistivity ◽  
Single Crystal ◽  
Room Temperature ◽  
Organic Conductor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Resistivity Measurements ◽  
Molecular Conductor ◽  
Abrupt Changes

Electrical resistivity measurements of a dual layered organic conductor (ET)4ZnBr4(1,2-C6H4Cl2) above room temperature show abrupt changes in resistivity at 320 K. Single-crystal X-ray diffraction studies in the 100-350 K range...

Synthesis, Structure and Magnetism of ErCoIn5

2004 ◽  
Vol 848 ◽  
Author(s):  
Evan Lyle Thomas ◽  
Erin E. Erickson ◽  
Monica Moldovan ◽  
David P. Young ◽  
Julia Y. Chan
Keyword(s):  
Magnetic Properties ◽  
Electrical Resistivity ◽  
Magnetic Susceptibility ◽  
Single Crystal ◽  
Experimental Results ◽  
Flux Growth ◽  
X Ray Diffraction ◽  
Metallic Behavior ◽  
X Ray ◽  
Growth Method

AbstractA new member of the LnMIn5 family, ErCoIn5, has been synthesized by a flux-growth method. The structure of ErCoIn5 was determined by single crystal X-ray diffraction. It crystallizes in the tetragonal space group P4/mmm, Z = 1, with lattice parameters a = 4.5400(4) and c = 7.3970(7) Å, and V = 152.46(2) Å3. Electrical resistivity data show metallic behavior. Magnetic susceptibility measurements show this compound to be antiferromagnetic with TN = 5.1 K. We compare these experimental results with those of LaCoIn5 in an effort to better understand the effect of the structural trends observed on the transport and magnetic properties.

scholarly journals Synthesis, Structure, and Properties of a Dinuclear Cu(II) Coordination Polymer Based on Quinoxaline and 3,3-Thiodipropionic Acid Ligands

2021 ◽  
Author(s):  
Adedibu Clement Tella ◽  
Samson Owalude ◽  
Vincent Adimula ◽  
Adetola Oladipo ◽  
Victoria Olayemi ◽  
...  
Keyword(s):  
Nmr Spectroscopy ◽  
Nitrogen Atom ◽  
Coordination Polymer ◽  
Elemental Analysis ◽  
Catalytic Reduction ◽  
Copper Acetate ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
H Nmr

Abstract The coordination polymer [Cu2(TDPH)4(QNX)].DMF, (QNX = Quinoxaline; TDPH = 3,3-thiodipropionic acid), has been prepared by reaction of copper acetate, TDPH, and quinoxaline. The compound was characterized by elemental analysis, FTIR spectroscopy, and single-crystal X-ray diffraction. The crystal is monoclinic with a P21/n space group and dimensions of a = 12.889(3) Å, b = 14.983(4) Å, c = 14.091(3) Å, α = 90 °, β = 90.200(11) °, γ = 90 °, V = 2721.18 (2) Å3, Z = 4. The ligands are hexagonally coordinated to the Cu(II) centre in the form of Cu2O4N with one nitrogen atom from the quinoxaline ligand, and four oxygen atoms from four TDPH molecules in a monodentate fashion. The Cu-Cu bond length was 2.642(1) and 2.629(1) Å for the Cu1----Cu1 and Cu2----Cu2 bonds. The QNX ligand bridged the two copper atoms. The catalytic reduction of 4-nitrophenol to 4-aminophenol using NaBH4 in the presence of [Cu2(TDPH)4(QNX)].DMF, as catalyst was completed within 11 minutes. The 4-aminophenol product was confirmed using 1H NMR spectroscopy.

scholarly journals Влияние Cr и Ni на формирование фаз в механосинтезированном нанокомпозите на основе Fe-=SUB=-75-=/SUB=-C-=SUB=-25-=/SUB=-

2020 ◽  
Vol 90 (5) ◽  
pp. 787
Author(s):  
А.А. Чулкина ◽  
А.И. Ульянов ◽  
В.А. Волков ◽  
А.Л. Ульянов ◽  
А.В. Загайнов
Keyword(s):  
Curie Temperature ◽  
Amorphous Phase ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
Nickel Content ◽  
X Ray Diffraction ◽  
Mechanical Synthesis ◽  
X Ray ◽  
Higher Temperature ◽  
Two Phases

X-ray diffraction, Mossbauer spectroscopy, and magnetic measurements have been used to study the phase formation and doping during mechanical synthesis (MS) and subsequent annealing of the alloy (Fe0.80Cr0.05Ni0.15)75C25. It has been shown that, after MS, the nanocomposite contains mainly two phases – an amorphous phase and cementite A. During annealing, as a result of crystallization of the amorphous phase, cementite B is formed, in which contains more nickel than in the mechanically synthesized cementite A. As the annealing temperature increases, austenite, which is inhomogeneous in nickel content, is formed. The Curie temperature of this austenite reaches 500 °C. It has been determined that cementite in the mechanosynthesized nanocomposite (Fe,Cr,Ni)75C25 has a higher temperature stabilitythan that in a MS composite (Fe,Ni)75C25.

Sign in / Sign up

Export Citation Format

Share Document