Effect of Mixing Condition on the Mechanical Properties of Magnesium Based Composites

2015 ◽  
Vol 1087 ◽  
pp. 434-438
Author(s):  
Wan Nur Azrina Wan Muhammad ◽  
Yoshiharu Mutoh
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Mixing Time ◽  
Mixing Conditions ◽  
Mixing Condition ◽  
Mixing Speed ◽  
Sic Particle

The effects of mixing conditions, i.e; mixing speed and mixing duration on the mechanical properties of the magnesium based composites were investigated. The hardness, tensile strength and microstructure of composites were studied. It was found that increase of the mixing speed and prolong the mixing time can improved the distribution of SiC particle and mechanical properties of magnesium based composites.

Effects of Different Processing Techniques on the Properties of PLA

2012 ◽  
Vol 550-553 ◽  
pp. 2932-2935
Author(s):  
Hong Juan Zheng ◽  
Yan Rong Wang ◽  
Zhi Wei Zhao ◽  
Lin Qi Zhang
Keyword(s):  
Mixing Time ◽  
Processing Temperature ◽  
Processing Conditions ◽  
Mixing Conditions ◽  
Processing Property ◽  
Obvious Effect ◽  
Good Thermal Stability ◽  
Mixing Speed ◽  
Internal Mixing ◽  
Processing Techniques

PLA has excellent processing property and good thermal stability, which are closely related to the processing technology, and the general processing temperature can be controlled in 170~230°C. Effects of different processing conditions (internal mixing temperature, internal mixing time and internal mixing speed) on the properties of PLA were discussed. The results show that the mechanical properties and other performance of PLA can be obviously enhanced by internal mixing. Internal mixing time and internal mixing speed have little effects on the performance of PLA, but the internal mixing temperature has obvious effect on the properties of PLA. PLA has the optimum properties when the internal mixing time is 5min, internal mixing speed is 20r/min and internal mixing temperature is 190°C. The spherocrystal size and spherocrystal rate of PLA are influenced strongly by the mixing conditions.

Effects of Mixing Parameters on Tensile Strength of TPU/NR Blends

2013 ◽  
Vol 291-294 ◽  
pp. 2654-2656
Author(s):  
Nor Azwin Ahad ◽  
Sahrim Hj Ahmad ◽  
Norazwani Muhammad Zain
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Polymer Blends ◽  
Mixing Time ◽  
Thermoplastic Polyurethane ◽  
Mixing Times ◽  
Melt Mixing ◽  
Mixing Parameters ◽  
The Poor

The blends of thermoplastic polyurethane (TPU) with natural rubber (NR) were prepared via melt mixing technique, at four different blending temperature at range 180°C - 210°C and mixing times of 8, 10, 12, 14 min. The effects of both mixing parameters on tensile strength of the blends were investigated. The blend of 85TPU15NR shows the maximum tensile strength at 180°C and 10 min mixing. The viscosity of the polymer blends will decrease as the temperature increased. The movements of molecules are more worthy because of the poor molecules interaction. The increasing of mixing time will increase the compatibility of the blends and also increase in mechanical properties. Mixing time and mixing temperature are important parameters in acquiring blends having optimum mechanical properties.

Processing of Clay/Epoxy Nanocomposites with A Three-Roll Mill Machine

2002 ◽  
Vol 740 ◽  
Author(s):  
Asma Yasmin ◽  
Jandro L. Abot ◽  
Isaac M. Daniel
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Mixing Time ◽  
Clay Content ◽  
Epoxy Nanocomposites ◽  
Clay Particles ◽  
Roll Mill ◽  
Short Period ◽  
Mixing Techniques ◽  
Xrd And Tem

ABSTRACTIn the present study, a three-roll mill machine was used to disperse/exfoliate the nanoclay particles in an epoxy matrix. The compounding process was carried out with varying mixing time and concentrations of clay particles (1 to 10 wt.%). It was found that the longer the mixing time, the higher the degree of intercalation. Mechanical properties, XRD and TEM were used to characterize the nanocomposites. Elastic modulus was found to increase with increasing clay content, however, the tensile strength was not found to vary accordingly. Compared to conventional direct and solution mixing techniques, the compounding of clay/epoxy nanocomposites by a three-roll mill was found to be highly efficient in achieving higher levels of intercalation/exfoliation in a short period of time and also environmentally friendly.

Influences of SiC Particle Size and Content on the Mechanical Properties and Wear Resistance of the Composites with Al Matrix

2008 ◽  
Vol 375-376 ◽  
pp. 430-434 ◽  
Author(s):  
Yi Yi Tao ◽  
Xiao Lan Ge ◽  
Xiao Jing Xu ◽  
Zuo Jiang
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Tensile Strength ◽  
Wear Resistance ◽  
Wear Properties ◽  
Reinforcing Effect ◽  
Sic Particles ◽  
Al Matrix ◽  
Sic Particle

The SiCp/Al composites reinforced by SiC particles with various sizes and contents were prepared by cold compacting and subsequent hot extruding. The mechanical and wear properties of the compositions were investigated and the relevant mechanisms were discussed. It has been shown that the tensile strength and wear resistance increases with increasing SiCp content. SiC particles have a remarkable reinforcing effect on matrix Al. The composite with larger SiCp size (14μm) possesses better wear resistance than that with smaller SiCp size (130nm).

Effects of Particle Size and Distribution on the Microstructure and Mechanical Properties of SiC Reinforced Al-30Si Alloy Composite

2012 ◽  
Vol 271-272 ◽  
pp. 12-16 ◽  
Author(s):  
Zeng Lei Ni ◽  
Ai Qin Wang ◽  
Jing Pei Xie
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Tensile Strength ◽  
Physical Properties ◽  
Combined Effects ◽  
Alloy Composite ◽  
Microstructure And Mechanical Properties ◽  
Sic Particles ◽  
The Matrix ◽  
Sic Particle

This paper studied the combined effects of particle size and distribution on the mechanical properties of the SiC particle reinforced Al-30Si alloy composites. The microstructure of experimental material was analyzed by SEM, the tensile strength and physical properties were examined. The results show that, with the increase of the SiC particle size in the composites, the clustering degree of the SiC particles decreases in the matrix, the SiC particles distribute more ununiformly. The tensile strength is influenced by the SiC particle size, the tensile strength of the composite reinforced by 13μm sized SiC particles is the highest.

Polyethylene/Clay Nanocomposites Prepared in an Internal Mixer: Effect of Processing Variable on Mechanical Properties

2015 ◽  
Vol 1105 ◽  
pp. 46-50 ◽  
Author(s):  
Onny Ujianto ◽  
Margaret Jollands ◽  
Nhol Kao
Keyword(s):  
Mechanical Properties ◽  
Mixing Time ◽  
Diffusion Mechanism ◽  
Clay Nanocomposites ◽  
Processing Conditions ◽  
Mixing Conditions ◽  
Material Degradation ◽  
Processing Variable ◽  
Internal Mixer ◽  
And Diffusion

Polymer/clay nanocomposites have been explored extensively over the last two decades. Many studies report nanocomposite properties. However, studies on the effect of processing conditions are still limited. This study evaluates the effect of rotor type, rotor rotation (rpm) and mixing time on mechanical properties of polyethylene organoclay composites. Samples were fabricated using two different rotors; roller and Banbury, in an internal batch mixer at various mixing conditions. The analysis shows that the Banbury rotor improved mechanical properties more than the roller rotor. Shear and diffusion mechanism, as well as material degradation, were the controlling factors at different processing conditions.

scholarly journals Physical and Numerical Modelling on the Mixing Condition in a 50 t Ladle

Metals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 1136
Author(s):  
Liu ◽  
Bai ◽  
Liu ◽  
Jönsson ◽  
Gan
Keyword(s):  
Mathematical Modelling ◽  
Flow Pattern ◽  
Flow Rate ◽  
Gas Flow ◽  
Transport Model ◽  
Mixing Time ◽  
Bubbly Flow ◽  
Physical Modelling ◽  
Mixing Conditions ◽  
Mixing Condition

The bubbly flow and mixing conditions for gas stirring in a 50t ladle were investigated by using physical modelling and mathematical modelling. In the physical modelling, the effect of the porous plugs’ configurations on the tracer homogenization was studied by using a saturated NaCl solution to predict the mixing time and a color dye to show the mixing pattern. In the mathematical modelling, the Euler–Lagrange model and species transport model were used to predict the flow pattern and tracer homogenization, respectively. The results show that, for a ±5% homogenization degree, the mixing time with dual plugs using a radial angle of 180° is shortest. In addition, the mixing time using a radial angle of 135° decreases the most with an increased flow rate. The flow pattern and mixing conditions predicted by mathematical modelling agree well with the result of the physical modelling. For a ±1% homogenization degree, the influence of the tracer’s natural convection on its homogenization pattern cannot be neglected. This is especially true for a ‘soft bubbling’ case using a low gas flow rate. Overall, it is recommended that large radial angles in the range of 135°~180° are chosen for gas stirring in the present study when using dual porous plugs.

Phase Transformations in Ti-7w/oMo-3w/oMe Alloy

1974 ◽  
Vol 32 ◽  
pp. 514-515
Author(s):  
S. Fujishiro
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Tensile Strength ◽  
Mechanical Processing ◽  
Ray Method ◽  
X Ray ◽  
Transmission Electron ◽  
Water Quench ◽  
Alpha Beta

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.

Effect of silver nitrate on some mechanical properties of heat polymerizing acrylic resins

2019 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Assiss. Prof. Dr. Sabiha Mahdi Mahdi ◽  
Dr. Firas Abd K. Abd K.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Silver Nitrate ◽  
Surface Hardness ◽  
Mechanical Tests ◽  
Hardness Tester ◽  
Acrylic Resins ◽  
The Difference

Aim: The aimed study was to evaluate the influence of silver nitrate on surfacehardness and tensile strength of acrylic resins.Materials and methods: A total of 60 specimens were made from heat polymerizingresins. Two mechanical tests were utilized (surface hardness and tensile strength)and 4 experimental groups according to the concentration of silver nitrate used.The specimens without the use of silver nitrate were considered as control. Fortensile strength, all specimens were subjected to force till fracture. For surfacehardness, the specimens were tested via a durometer hardness tester. Allspecimens data were analyzed via ANOVA and Tukey tests.Results: The addition of silver nitrate to acrylic resins reduced significantly thetensile strength. Statistically, highly significant differences were found among allgroups (P≤0.001). Also, the difference between control and experimental groupswas highly significant (P≤0.001). For surface hardness, the silver nitrate improvedthe surface hardness of acrylics. Highly significant differences were statisticallyobserved between control and 900 ppm group (P≤0.001); and among all groups(P≤0.001)with exception that no significant differences between control and150ppm; and between 150ppm and 900ppm groups(P>0.05).Conclusion: The addition of silver nitrate to acrylics reduced significantly the tensilestrength and improved slightly the surface hardness.

Sign in / Sign up

Export Citation Format

Share Document