Treatment of Oily Sludge from Floatation Process: Floc Breakage and Dewatering

2010 ◽  
Vol 113-116 ◽  
pp. 579-583 ◽  
Author(s):  
Gang Li ◽  
Shu Hai Guo ◽  
Chun Shan Zhang ◽  
Xi Lin Liu
Keyword(s):  
Produced Water ◽  
Interstitial Water ◽  
Average Diameter ◽  
Oily Sludge ◽  
Capillary Suction ◽  
Median Diameter ◽  
Gravity Sedimentation ◽  
Granularity Distribution ◽  
Floatation Process ◽  
Floc Breakage

The aim is to treat oily sludge from floatation process of oil produced water by deflocculation. Based upon analyzing the granularity distribution and dewater efficiency of the flocs, floc breakage and dewater of oily sludge was carried out. The results indicated that the coagulant skeleton builder in sludge could be broken by changing the coalescent state, and deflocculation could disrupt skeleton of the floc and release interstitial water in sludge. The highest dewatering efficiency is about 81.2% at the pH of 4.5 by gravity sedimentation. The sludge had a broader range of granularity distribution and a smaller volume-average diameter. Moreover, the median diameter d (0.5) of the treated sludge was 36.0 μm, which was smaller than 73.1 μm of raw sample. Meanwhile, capillary suction time (CST) significantly decreased with pH adjustment. A wastewater removal efficiency of 90.99% for the treated sludge by pressure filtration could be achieved. The method would be a potential technique to be applied to other kinds of floatation sludge.

Comparison of lime and alum as oily sludge conditioners

1997 ◽  
Vol 36 (12) ◽  
pp. 117-124 ◽  
Author(s):  
Tay Joo Hwa ◽  
S. Jeyaseelan
Keyword(s):  
Specific Resistance ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oily Sludge ◽  
Sludge Dewatering ◽  
Capillary Suction ◽  
Sludge Cake ◽  
Solids Content ◽  
Optimum Chemical

Chemical conditioning improves sludge dewatering. Choice of chemical conditioners is very much dependent on the characteristics of the sludges and the type of dewatering devices. Lime, alum, ferric chloride and polyelectrolytes are commonly used chemical conditioners. Anaerobic digested sludge samples collected from a sewage treatment plant with different oil contents varying from 1.8% to 8.0% by weight have been examined in the laboratory to find out their specific resistance, capillary suction time and filter yield. Lime and alum were used separately as conditioners. Different dosages of conditioner varying from 2% to 12% by weight were used to determine the optimum chemical dosage for varying oil contents. Lime dosages of about 6% were found to yield favourable characteristics. Addition of alum decreases the specific resistances and capillary suction times of oily sludges rapidly up to 4% dosages. Alum dosages beyond 4% only increase the solids content in the sludge cake and increase the sludge volume to be handled. A correlation between CST and specific resistance to filtration was established. CST can be measured easily and quickly in the laboratories. Using the CST and the correlation a quick prediction on dewaterability can be established.

Dewatering Characteristics of Oily Sludge

1993 ◽  
Vol 28 (1) ◽  
pp. 249-256 ◽  
Author(s):  
Joo-Hwa Tay ◽  
S. Jeyaseelan
Keyword(s):  
Oil Content ◽  
Specific Resistance ◽  
Solid Content ◽  
Oily Sludge ◽  
Capillary Suction ◽  
Optimum Dosage ◽  
Sludge Conditioning

Proper sludge conditioning facilitates better dewatering of sludges. Sludge conditioning techniques required for different sludges bigbly depend on the properties of the sludges. Dewatering characteristics of oily sludges were studied for different degrees of oil content in sludge with lime as sludge conditioner. The optimum dosage of lime was found to range from 6% to 10% to yield favourable characteristics of the sludge for better filterability. Also the established correlations between the combinations of dewatering characteristics, such as specific resistance, capillary suction time, cake solid content and filter yield provide means of quick indication for the nature of the sludges.

Biosurfactant production for enhancing the treatment of produced water and bioremediation of oily sludge under the conditions of Gachsaran oil field

2016 ◽  
Vol 92 (5) ◽  
pp. 1053-1064 ◽  
Author(s):  
Masoud Rahbari-Sisakht ◽  
Abdolrasoul Pouranfard ◽  
Parviz Darvishi ◽  
Ahmad Fauzi Ismail
Keyword(s):  
Produced Water ◽  
Oil Field ◽  
Biosurfactant Production ◽  
Oily Sludge

Research on Multi-Cup Uniform Flow Gravity Sedimentation Single Well Injection-Production Technique

2013 ◽  
Vol 341-342 ◽  
pp. 534-539
Author(s):  
Guo Xing Zheng
Keyword(s):  
Produced Water ◽  
Water Injection ◽  
Uniform Flow ◽  
Water Mixture ◽  
Production Technique ◽  
Water Separator ◽  
Single Well ◽  
Oil Water ◽  
Gravity Sedimentation ◽  
Water Cut

When the oilfield enters the hing water cut stage, the mining faces the problem that the oil-gas gathering system energy consumption reduction needs to decrease produced water and water injection. This paper proposes a novel multi-cup uniform flow gravity sedimentation single well injection-production technique. The downhole oil-water separator separates oil from water. The separated water is directly reinjected into the injection layer. Higher oil content of oil-water mixture is lifted up to the ground. The water injection and oil production in the production wellbore are simultaneous. This paper also designs a crown-like sedimentation cup structure. The experiment shows that the optimum structure of crown oil-water separator is cylindrical with 30 inclination, 12 edges and one partition baord on the tip at the bottom of corrugated shape. Produced liquid contains water 95 percent; efficiency can be increased more than three times by using multi-cup uniform flow gravity sedimentation separator.

Two Distinct Types of Microfilaments in the Cytoplasm of Human Adenohypophysial Cells

1973 ◽  
Vol 31 ◽  
pp. 668-669
Author(s):  
E. Horvath ◽  
K. Kovacs ◽  
I. E. Stratmann ◽  
C. Ezrin
Keyword(s):  
Pituitary Tumors ◽  
Average Diameter ◽  
Anterior Lobe ◽  
Uranyl Acetate ◽  
Type I ◽  
Breast Cancer Patients ◽  
Human Pituitary ◽  
Severe Diabetes ◽  
Pituitary Glands ◽  
Membrane Bound

Surgically removed human pituitary glands as well as pituitary tumors fixed in glutaraldehyde, postfixed in osmium tetroxide, embedded in epon resin, stained with uranyl acetate and lead citrate have been investigated by electron microscopy in order to correlate ultrastructure with functional activity. In the course of this study two distinct types of microfilaments have been identified in the cytoplasm of adenohypophysiocytes.Type I microfilaments (Fig. 1) were found in the cytoplasm of anterior lobe cells of five female subjects with disseminated mammary cancer and two patients with severe diabetes mellitus. The breast cancer patients were treated pre-operatively for various periods of time with different doses of oxysteroids. The microfilaments had an average diameter of JO A, formed parallel bundles, were scattered irregularly in the cytoplasm and were frequently located in the perikaryon. They were not membrane-bound and failed to show any periodicity.

Imaging of platinum-shadowed macromolecular complexes in dark field

1984 ◽  
Vol 42 ◽  
pp. 146-147
Author(s):  
D.W. Andrews ◽  
F.P. Ottensmeyer
Keyword(s):  
Thin Film ◽  
Three Dimensional ◽  
Average Diameter ◽  
Dark Field ◽  
Bright Field ◽  
Field Mode ◽  
Macromolecular Complexes ◽  
Average Mass ◽  
Topological Features ◽  
Projection Images

Shadowing with heavy metals has been used for many years to enhance the topological features of biological macromolecular complexes. The three dimensional features present in directionaly shadowed specimens often simplifies interpretation of projection images provided by other techniques. One difficulty with the method is the relatively large amount of metal used to achieve sufficient contrast in bright field images. Thick shadow films are undesirable because they decrease resolution due to an increased tendency for microcrystalline aggregates to form, because decoration artefacts become more severe and increased cap thickness makes estimation of dimensions more uncertain.The large increase in contrast provided by the dark field mode of imaging allows the use of shadow replicas with a much lower average mass thickness. To form the images in Fig. 1, latex spheres of 0.087 μ average diameter were unidirectionally shadowed with platinum carbon (Pt-C) and a thin film of carbon was indirectly evaporated on the specimen as a support.

Digital image processing methods applied to the study of annealing time on semiconductor-metal eutectic composites

1988 ◽  
Vol 46 ◽  
pp. 848-849
Author(s):  
J. Hefter
Keyword(s):  
Image Processing ◽  
Digital Image Processing ◽  
Digital Image ◽  
Electronic Device ◽  
Processing System ◽  
Average Diameter ◽  
Eutectic Solidification ◽  
Metal Silicide ◽  
The Matrix ◽  
Microscopic Studies

Semiconductor-metal composites, formed by the eutectic solidification of silicon and a metal silicide have been under investigation for some time for a number of electronic device applications. This composite system is comprised of a silicon matrix containing extended metal-silicide rod-shaped structures aligned in parallel throughout the material. The average diameter of such a rod in a typical system is about 1 μm. Thus, characterization of the rod morphology by electron microscope methods is necessitated.The types of morphometric information that may be obtained from such microscopic studies coupled with image processing are (i) the area fraction of rods in the matrix, (ii) the average rod diameter, (iii) an average circularity (roundness), and (iv) the number density (Nd;rods/cm2). To acquire electron images of these materials, a digital image processing system (Tracor Northern 5500/5600) attached to a JEOL JXA-840 analytical SEM has been used.

A magnetic super lattice

1987 ◽  
Vol 45 ◽  
pp. 360-361 ◽  
Author(s):  
M.D. Bentzon ◽  
J. v. Wonterghem ◽  
A. Thölén
Keyword(s):  
Thermal Decomposition ◽  
Oleic Acid ◽  
Magnetic Fluid ◽  
Magnetic Particles ◽  
Carbon Film ◽  
Thick Layer ◽  
Amorphous Iron ◽  
Super Lattice ◽  
Carrier Liquid ◽  
Median Diameter

We report on the oxidation of a magnetic fluid. The oxidation results in magnetic super lattice crystals. The “atoms” are hematite (α-Fe2O3) particles with a diameter ø = 6.9 nm and they are covered with a 1-2 nm thick layer of surfactant molecules.Magnetic fluids are homogeneous suspensions of small magnetic particles in a carrier liquid. To prevent agglomeration, the particles are coated with surfactant molecules. The magnetic fluid studied in this work was produced by thermal decomposition of Fe(CO)5 in Declin (carrier liquid) in the presence of oleic acid (surfactant). The magnetic particles consist of an amorphous iron-carbon alloy. For TEM investigation a droplet of the fluid was added to benzine and a carbon film on a copper net was immersed. When exposed to air the sample starts burning. The oxidation and electron irradiation transform the magnetic particles into hematite (α-Fe2O3) particles with a median diameter ø = 6.9 nm.

Potential of recovering elements from produced water at oil and gas fields, British Columbia, Canada

CIM Journal ◽  
2018 ◽  
Vol 9 (4) ◽  
pp. 195-214
Author(s):  
G. J. Simandl ◽  
C. Akam ◽  
M. Yakimoski ◽  
D. Richardson ◽  
A. Teucher ◽  
...  
Keyword(s):  
British Columbia ◽  
Oil And Gas ◽  
Produced Water ◽  
Oil And Gas Fields ◽  
Gas Fields

Morphometric characteristics of competent proximal valves of the great saphenous vein and superficial femoral vein in vivo according to ultrasound angioscanning data

2019 ◽  
Vol 18 (3) ◽  
pp. 16-22
Author(s):  
E. K. Gavrilov ◽  
H. L. Bolotokov ◽  
E. A. Babinets
Keyword(s):  
Saphenous Vein ◽  
Great Saphenous Vein ◽  
Femoral Vein ◽  
Lower Boundary ◽  
Average Diameter ◽  
Lower Limbs ◽  
Functional Test ◽  
Natural Form ◽  
Superficial Femoral Vein ◽  
Venous Diameter

Introduction. It seems relevant to study the ultrasound anatomy and physiology of the proximal valve segments of the superficial femoral vein (SFV) and the great saphenous vein (GSV) to develop effective reconstructive surgical interventions on venous valves in chronic vein diseases.The aim of the survey was to study the ultrasound anatomy of the venous wall, the size and shape of the proximal SFV and GSV valves are normal at rest and during the functional test Valsalva.Material and methods. Proximal valve SFV studies were performed in 144 lower limbs in 115 people (mean age 51.1 ± 14.4 years, 60 women and 55 men), proximal GSV valves studies - in 82 lower limbs in 67 persons (average age 45, 1 ± 13.3 years, 33 women, 34 men). A longitudinal and transverse ultrasound scanning of the femoral vein bifurcation and safenofemoral junction areas were performed, the structures of the proximal SFV and GSV valves were visualized, the valve shape was measured and the diameter of the veins was measured at the level valves at the base of the valves (inlet diameter), at the point of maximum ectasia (diameter of ectasia), at the upper border of the valve (diameter of the outlet), as well as measuring the length of the valve a (length to ectasia, the total length of the valve). The degree of ectasia over the valve was judged by calculating the relative venous diameter change (RVDC).Results. the average diameter of the SFV at the level of the lower boundary of its first valve was 10.01 ± 1.44 mm. The average diameter of the SFV at the level of the maximum ectasia of its first valve was 13,1±2 mm. The average value of the index of RVDC for SFV was 31%±10,4%. An increase in the diameter of the vein in the zone of supravalvular ectasia up to 20% corresponded to the spindle-shaped valve, more than 20% - to the clavate form, which was noted in the majority of the examined. The change in the relative venous diameter of the SFV on the Valsalva test was 38,2%±12,4%. The average diameter of the GSV at the base of the first valves was 6,07±1,25 mm. The average diameter of the GSV at the level of the maximum ectasia of the osteal valve was 9,44±1,69 mm. The average RVDC for GSV was 58%±24%.Conclusion. the natural form of proximal SFV and GSV valves is clavate with presence of the significant supravalvular ectasia, which was noted in the majority of the subjects alone and in all during the performance of the Valsalva functional test.

Sign in / Sign up

Export Citation Format

Share Document