Development of Low Carbon Bainitic Cr-B Steel with High Strength and Good Toughness

2010 ◽  
Vol 146-147 ◽  
pp. 937-940
Author(s):  
Xiang Dong Huo ◽  
Zhang Guo Lin ◽  
Yu Tao Zhao ◽  
Yu Qian Li
Keyword(s):  
High Strength ◽  
Polygonal Ferrite ◽  
Steel Plates ◽  
Granular Bainite ◽  
High Yield ◽  
Low Carbon ◽  
Experimental Steel ◽  
Large Size ◽  
Final Microstructure ◽  
Lath Bainite

In order to develop low carbon bainitic Cr-B steel, experimental procedures including melting, thermal simulation study and laboratory hot rolling were adopted. The dynamic CCT diagram was established, microstructure and properties of experimental steel were also analyzed. The transformation temperature of experimental steel lies between 650～400°C and final microstructure changes fromquasi-polygonal ferrite, granular bainite to lath bainite as cooling rate increases from 0.2 to 50°C.s-1. The microstructure of steel plates, air cooled or water cooled to 530°C then air cooled, is mainly composed of granular bainite and quasi-polygonal ferrite, and the large size islands in granular bainite are responsible for the low strength and poor toughness. However, steel plate with lath bainite, water cooled to roomtemperature, boasts high yield strength (672MPa) and superior impact toughness (127J at -20°C). Therefore, it is feasible to produce low carbon bainitic Cr-B steel with high strength and good toughness through controlling cooling parameters.

scholarly journals Morphology and Crystallography Analyses of HSLA Steels with Hardenability Enhanced by Tailored C–Ni Collocation

Metals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 32
Author(s):  
Zhipeng Liu ◽  
Yishuang Yu ◽  
Jie Yang ◽  
Zhiquan Wang ◽  
Hui Guo ◽  
...  
Keyword(s):  
Driving Force ◽  
Nickel Content ◽  
High Strength ◽  
Transformation Strain ◽  
Steel Plates ◽  
Granular Bainite ◽  
Variant Selection ◽  
High Hardenability ◽  
Hsla Steels ◽  
Lath Bainite

High hardenability is of great importance to ultra-heavy steel plates and can be achieved by tailoring the composition of steel. In this study, the continuous cooling transformation (CCT) curves of two high-strength low-alloy (HSLA) steels (0.16C-0.92Ni steel and 0.12C-1.86Ni steel) were elucidated to reveal the significance of C–Ni collocation on hardenability from the perspective of morphology and crystallography. At a low cooling rate (0.5 °C/s), the 0.12C-1.86Ni steel showed higher microhardness than 0.16C-0.92Ni steel. The microstructure in 0.16C-0.92Ni steel was mainly granular bainite with block-shaped martensite/austenite islands (M/A islands), while that in 0.12C-1.86Ni steel was typically lath bainite with film-shaped M/A islands, denoting that the 0.12C-1.86Ni steel is of higher hardenability. Moreover, the 0.12C-1.86Ni steel exhibited a higher density of block boundaries, especially V1/V2 boundaries. The higher density of block boundaries resulted from the weakened variant selection due to the larger transformation driving force and more self-accommodation of transformation strain induced by the reduced carbon and increased nickel content.

scholarly journals Continuous Cooling Transformation Diagram, Microstructures, and Properties of the Simulated Coarse-Grain Heat-Affected Zone in a Low-Carbon Bainite E550 Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 939 ◽  
Author(s):  
Yun Zong ◽  
Chun-Ming Liu
Keyword(s):  
Impact Toughness ◽  
Cooling Rate ◽  
Vickers Hardness ◽  
Heat Affected Zone ◽  
Granular Bainite ◽  
Coarse Grain ◽  
Low Carbon ◽  
Transformation Diagram ◽  
Lath Bainite ◽  
Continuous Cooling Transformation Diagram

In order to provide important guidance for controlling and obtaining the optimal microstructures and mechanical properties of a welded joint, the continuous cooling transformation diagram of a new low-carbon Nb-microalloyed bainite E550 steel in a simulated coarse-grain heat-affected zone (CGHAZ) has been constructed by thermal dilatation method in this paper. The welding thermal simulation experiments were conducted on a Gleeble-3800 thermo-mechanical simulator. The corresponding microstructure was observed by a LEICA DM2700M. The Vickers hardness (HV) and the impact toughness at −40 °C were measured according to the ASTM E384 standard and the ASTM E2298 standard, respectively. The experimental results may indicate that the intermediate temperature phase transformation of the whole bainite can occur in a wide range of cooling rates of 2–20 °C/s. In the scope of cooling rates 2–20 °C/s, the microstructure of the heat-affected zone (HAZ) mainly consists of lath bainite and granular bainite. Moreover, the proportion of lath bainite increased and granular bainite decreased as the cooling rate increasing. There is a spot of lath martensite in the microstructure of HAZ when the cooling rate is above 20 °C/s. The Vickers hardness increases gradually with the increasing of the cooling rate, and the maximum hardness is 323 HV10. When the cooling time from 800 °C to 500 °C (t8/5) is 5–15 s, it presents excellent −40 °C impact toughness (273–286 J) of the CGHAZ beyond the base material (163 J).

scholarly journals Morphological and Crystallographic Characteristics of α Structure in a Low-Carbon Iron–Nickel Alloy

Crystals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 468 ◽  
Author(s):  
Gaojun Mao ◽  
Cyril Cayron ◽  
Xiuli Mao ◽  
Rui Cao ◽  
Roland Logé ◽  
...  
Keyword(s):  
Lath Martensite ◽  
Granular Bainite ◽  
Body Centered Cubic ◽  
Low Carbon ◽  
Electron Backscattered Diffraction ◽  
Dislocation Densities ◽  
Lath Bainite ◽  
Crystallographic Characteristics ◽  
Iron Nickel ◽  
Relationship Of

The features of α (body-centered cubic) structures were investigated in a low-carbon multicomponent alloy from morphological and crystallographic perspectives. In addition to apparent features of granular bainite and lamellar martensite, a morphological similarity can be found between lath martensite and lath bainite. Therefore, it is of interest to explore possible discrepancies between lath martensite and lath bainite from a crystallographic perspective. These microstructures were obtained by various cooling rates (i.e., water quenching, 5 °C/s, and 0.05 °C/s) and then were characterized by a combination of scanning electron microscopy and electron backscattered diffraction techniques. It is shown that: (1) Lath martensite (LM) formed in the samples that were water-quenched, and a mixture of LM and lath bainite (LB) and granular bainite (GB) formed in the samples cooled at rates of 5 °C/s and 0.05 °C/s, respectively; (2) A Kurdjumov-Sachs relationship was mostly found in as-quenched martensite, while a Greninger-Troiano relationship represented the orientation relationship of LB and GB; (3) As the cooling rate decreased, the dislocation densities in corresponding microstructures were reduced, while the tendency of variant grouping was enhanced.

On the Microstructure of Plate Steels for API-5L X120 Applications

2012 ◽  
Vol 706-709 ◽  
pp. 17-23 ◽  
Author(s):  
C. Isaac Garcia ◽  
Ming Jian Hua ◽  
X. Liang ◽  
P. Suikannen ◽  
Anthony J. DeArdo
Keyword(s):  
Hsla Steel ◽  
High Strength ◽  
Steel Plates ◽  
Low Carbon ◽  
Austenite Grain Size ◽  
Direct Quenching ◽  
Prior Austenite Grain Size ◽  
Optical Examination ◽  
Very High

The very high strength now achievable in low carbon HSLA steel plates is caused by the formation of bainite or martensite during the post-hot rolling cooling in interrupted direct quenching. Modern electron optical examination, especially FEG-SEM, has allowed the microstructural features such as packet, block and lath dimensions and crystallography to be quantitatively determined. Several recent studies have attempted to relate the strength and toughness to these features, with limited success. However, one observation is clear, these microstructural features scale with the prior-austenite grain size and state of recrystallization. The role of microalloying, beyond grain refinement, remains inconclusive. This paper will discuss these microstructures and suggest possible ways of further refining them.

Microstructure and Mechanical Properties of X80/X100 High Deformability Pipeline Steel

2011 ◽  
Vol 399-401 ◽  
pp. 139-143
Author(s):  
Dian Xiu Xia ◽  
De Liang Meng ◽  
Shou Yong An ◽  
Yong Lin Kang
Keyword(s):  
Pipeline Steel ◽  
Large Strain ◽  
High Strength ◽  
Longitudinal Direction ◽  
Granular Bainite ◽  
Dual Phase ◽  
Cooling Process ◽  
Bainite Structure ◽  
Lath Bainite ◽  
High Deformability

In the present study, X80 and X100 grade high deformability pipeline steels have been processed by using TMCP and followed two-stage cooling process. The microstructures of the X80HD (HD, high deformability) and X100HD steels were both characterized by ferrite-bainite dual phase. The grains sizes of ferrite were mostly less than 5μm and the volume fractions were about 20~25% in X80HD and 10~15% in X100HD steel. The bainite structure in X80HD steel was granular bainite (GB); while in X100HD steel large amounts of lath bainite (LB) were also formed besides GB, and bainite grains were much finer. Ferrite-bainite dual phase microstructure has large strain hardenability that resulting high strength and high deformability combination. Both the steels exhibit high strength/toughness in transverse direction and high deformability in longitudinal direction. The X100HD steel with more volume of LB and less volume of PF has higher strength but lower deformability than that of X80HD steel.

Refinement of Cementite in High Strength Steel Plates by Rapid Heating and Tempering

2007 ◽  
Vol 539-543 ◽  
pp. 4720-4725 ◽  
Author(s):  
A. Nagao ◽  
K. Hayashi ◽  
K. Oi ◽  
S. Mitao ◽  
N. Shikanai
Keyword(s):  
Rapid Heating ◽  
High Strength ◽  
Average Diameter ◽  
Carbon Steels ◽  
Steel Plates ◽  
Heating Process ◽  
Low Carbon ◽  
Precipitation Behavior ◽  
Heating Rates ◽  
Extraction Replica

The precipitation behavior of cementite in low carbon steels at various heating rates from 0.3 to 100 K/s has been studied using a high-frequency induction heating apparatus. The materials used in this study were steel platesfor welded structures: 610 and 780 MPa class steel plates with a mixed microstructure of bainite and martensite.Cementite was observed using a carbon extraction replica method and the hardness and toughness were also examined. When heated at the conventional slow rate of 0.3 K/s, relatively large cementite particles with an average diameter of 72 nm precipitated at the lath boundaries, whereas when heated at a rapid rate over 3.0 K/s, cementite precipitated both within the laths and at the lath boundaries, and the cementite was refined down to an average diameter of 54 nm. With such refinement of the cementite, the toughness was improved. On the other hand, the hardness was irrespective of the heating rate and was dependent on the tempering parameter. TEM observations of the cementite precipitation behavior during the rapid heating process revealed that cementite begins to precipitate at the lath boundaries at about 773 K and within the laths at about 873 K. It is concluded that rapid heating especially from 773 to 873 K contributes to the cementite refinement and consequently the improvement in toughness. The effect of alloying elements such as chromium, molybdenum or silicon on the cementite growth during the rapid heating and tempering treatment is also discussed.

Microstructure and Mechanical Properties of X70 Pipeline Steel with High H2S Resistance

2015 ◽  
Vol 816 ◽  
pp. 755-760 ◽  
Author(s):  
Jing Li ◽  
Xiu Hua Gao ◽  
Yong Lu ◽  
Lin Xiu Du
Keyword(s):  
Mechanical Properties ◽  
Pipeline Steel ◽  
High Strength ◽  
Granular Bainite ◽  
Second Phase ◽  
Precipitation Behavior ◽  
Experimental Steel ◽  
X70 Pipeline Steel ◽  
The Matrix ◽  
Sour Service

Anti-H2S X70 pipeline steel was developed. The microstructure of X70 pipeline steel was studied by the analysis of OM, SEM and TEM. The precipitation behavior was discussed. The comprehensive mechanical properties, HIC and SCC performance were systematically studied. The results indicated that the microstructure of the experimental steel was mainly acicular ferrite and granular bainite. The second phase precipitates dispersedly distributed in the matrix. The experimental steel possessed excellent strength, plasticity, low temperature toughness and low yield ratio. And therefore, the X70 pipeline steel in the study is suitable for sour service with the high strength, excellent toughness and low HIC&SSC susceptibility.

Nucleation Effect of Ca-Oxysulfide Inclusions of Low Carbon Steel in Heat Affected Zone by Welding

2018 ◽  
Vol 941 ◽  
pp. 130-134
Author(s):  
Yusuke Terazawa ◽  
Katsuyuki Ichimiya ◽  
Kazukuni Hase
Keyword(s):  
Carbon Steel ◽  
Heat Affected Zone ◽  
Heat Input ◽  
Fine Particles ◽  
Low Carbon Steel ◽  
Lattice Misfit ◽  
Polygonal Ferrite ◽  
Steel Plates ◽  
Low Carbon ◽  
Nucleation Effect

In order to achieve excellent toughness of heat affected zone (HAZ) of low carbon steel plates by welding, several microstructure control techniques using fine particles have been developed. In particular, Ca-oxysulfide inclusions have been used in a lot of steel plate products, because they are thermally stable even in near the fusion line of weld joint and they have grain refining effect in HAZ. In cases where heat input is large (>100kJ/cm) and microstructure of HAZ mainly consists of polygonal ferrite, it has been clarified that Ca-oxysulfide inclusions act as nucleation sites of polygonal ferrite in HAZ during the cooling process after welding. However, in cases where heat input is medium (≈50kJ/cm) and microstructure of HAZ mainly consists of bainite, nucleation effect of Ca-oxysulfide inclusions and that of mechanism have not been clarified. This study investigated the nucleation effect of Ca-oxysulfide inclusions in medium heat input welding by in-situ laser microscope observation and the lattice misfit between Fe-matrix and Ca-oxysulfide inclusions.

EBSD Study of the Effect of Hot Deformation on Low Carbon Bainitic Structure

2020 ◽  
Vol 993 ◽  
pp. 513-519
Author(s):  
Xin Li Wen
Keyword(s):  
Grain Size ◽  
Thickness Reduction ◽  
Granular Bainite ◽  
Low Carbon ◽  
Remarkable Effect ◽  
Lath Bainite ◽  
Effective Grain Size ◽  
Bainitic Structure ◽  
Ebsd Technique ◽  
The Given

The effect of deformation temperature (DT) and thickness reduction on the bainitic structure was investigated under various test conditions by using hot compression on a Gleeble-1500 thermo-mechanical simulation machine, and electron back scattering diffraction (EBSD) technique. In the case of the bainitic structure consisting of granular bainite (GB), lath bainite (LB) and a little ferrite (AF) under the given deformation conditions, DT and thickness reduction have remarkable effect on the transformation kinetics, starting temperature (B) of bainite fast transformation, and the type of bainitic structure. With the decreasing of DT from 810 °C to 730 °C, the starting temperature of transformation B increase from 585 °C to 595 °C. When the thickness reduction was 0 % and 20 %, the microstructure consists of GB, LB and a little AF, whereas as the thickness reduction increase to 40 %, large grain size of LB and GB disappear, and only AF and M/A remained. With the thickness reduction increases from 0 % to 40 %, the effective grain size decreases from 4 μm to 2 μm, and the fraction of HGB increases from 48 % to 57 %.

CARPENTER CUSTOM 455

Alloy Digest ◽  
1967 ◽  
Vol 16 (4) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stainless Steel ◽  
Precipitation Hardening ◽  
Martensitic Stainless Steel ◽  
Aging Treatment ◽  
High Strength ◽  
Heat Treating ◽  
High Yield ◽  
Low Carbon ◽  
High Yield Strength

Abstract Carpenter Custom 455 is a low-carbon martensitic stainless steel that responds to precipitation-hardening. The single aging treatment produces exceptionally high yield strength with good ductility and toughness. It is suitable for applications requiring high strength and corrosion resistance at temperatures up to 800 F. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-193. Producer or source: Carpenter.

Sign in / Sign up

Export Citation Format

Share Document