Preparation and Mechanical Properties of Polyurethane Elastomer with Two Soft Segments of HTPB/PTMG

2010 ◽  
Vol 150-151 ◽  
pp. 1689-1692 ◽  
Author(s):  
Hai Tao Tao ◽  
Xi Jun Liu ◽  
Tie Ning Ma
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Molecular Weight ◽  
Treatment Time ◽  
Treatment Temperature ◽  
Chain Extender ◽  
Toluene Diisocyanate ◽  
Molar Ratio ◽  
Mass Ratio ◽  
Polyurethane Elastomers

In this paper, a series of polyurethane elastomers (PUE) were prepared employing casting method using toluene diisocyanate (TDI), hydroxy-terminated butadiene-acrylonitrile copolymer(HTBN) and polytetrahydrofuran glycol (PTMG) as the main raw materials, and using 2,4- and 2,6- dimethylthioaromatic diamine (DMTDA) as a chain extender. The effects of the content of NCO in PUE (NCO%), mass ratio of HTBN/PTMG, molecular weight of PTMG, dosage of chain extender and heat treatment on the mechanical properties of PUE were studied. The results showed that the lower molecular weight of PTMG and the higher heat treatment temperature were both favorable for increasing the mechanical properties of PUE. When the mass ratio of HTBN/PTMG was 35:65, NCO% was 6.0%, molar ratio of NCO/NH2 was 1.20 and heat treatment time was 2h at 115 , the mechanical properties of PUE were best.

Study on Mechanical Properties of Polyurethane Elastomers for Drum Scraper

2011 ◽  
Vol 284-286 ◽  
pp. 2384-2387
Author(s):  
Jin Cui Zhang ◽  
Xi Jun Liu ◽  
Tie Ning Ma
Keyword(s):  
Mechanical Properties ◽  
Chain Extender ◽  
Glycol Ether ◽  
Toluene Diisocyanate ◽  
Chain Extension ◽  
Molar Ratio ◽  
Casting Method ◽  
Polyurethane Elastomers ◽  
Application Requirements

Polyurethane elastomers (PUE) were prepared by casting method using the prepolymer and the chain extender. In here, the prepolymer synthesized by using poly(tetramethylene glycol ether) (PTMG) and toluene diisocyanate (TDI), the chain extender was a mixture of 3,5-dimetylthio toluene diamine (E-300) and triethanolamine. The effects of the NCO concentration in prepolymer, the molar ratio of E-300/triethanolamine, and the chain extension coefficient of NCO/NH2 on the mechanical properties of the prepared PUE were studied. The results showed that the prepared PUE possesses excellent mechanical properties which can meet the drum scraper’s application requirements when the NCO concentration in prepolymer was 5.06% and the molar ratio of composite chain extender was 0.92/0.08.

Research on Microstructure and Mechanical Properties Evolution of Rheocast and Thixocast 319s Aluminum Alloy

2016 ◽  
Vol 850 ◽  
pp. 802-808 ◽  
Author(s):  
Kang Du ◽  
Xiao Kang Liang ◽  
Da Quan Li ◽  
Qiang Zhu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Time ◽  
Eutectic Silicon ◽  
Solution Treatment ◽  
Treatment Temperature ◽  
Solid Alloy ◽  
Obvious Effect ◽  
Higher Temperature ◽  
Semi Solid

In semi-solid rheocast and thixocast industry, T6 heat treatment was one key factor to improve the mechanical properties of the castings. The microstructure evolution was closely influenced by heat treatment temperature and time. In this paper, the morphology change of eutectic silicon in semi-solid alloy during different heat treatment time was firstly observed. The changes of both roundness and aspect show that the silicon particles underwent fragmentation, coarsening and growing up processes during solution treatment. Then, the mechanical properties after stand T6 and T6 with higher temperature were compared. It may be concluded that the higher temperature doesn’t have obvious effect to increase the mechanical strength, but severe negative effect on the elongation. Finally, the incipient melting defect appeared in higher temperature T6 was proved and its relationship with elongation was analysed.

Effect of High Temperature on the Change in Color, Dimensional Stability and Mechanical Properties of Spruce Wood

Holzforschung ◽  
2003 ◽  
Vol 57 (5) ◽  
pp. 539-546 ◽  
Author(s):  
P. Bekhta ◽  
P. Niemz
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
High Temperature ◽  
Dimensional Stability ◽  
Modulus Of Elasticity ◽  
Bending Strength ◽  
Treatment Time ◽  
Color Difference ◽  
Treatment Temperature ◽  
Color Changes

Summary In this study the effect of high temperature on mechanical properties, dimensional stability and color of spruce was investigated. Wood specimens conditioned at different relative humidities (50, 65, 80 and 95%) were subjected to heat treatment at 200°C for 2, 4, 8, 10 and 24 h and at 100, 150 and 200°C for 24 h. Color changes were measured in the Minolta Croma-Meter CR-300 color system. Bending strength and modulus of elasticity were determined according to DIN 52186. The results show that heat treatment mainly resulted in a darkening of wood tissues, improvement of the dimensional stability of wood and reduction of its mechanical properties. The darkening accelerated generally when treatment temperature exceeded approximately 200°C. Most of the darkening occurred within the first 4 h of exposure. For the specimens heated to high temperatures, the average decrease in bending strength was about 44–50%, while modulus of elasticity was reduced by only 4–9%. We found that treatment time and temperature were more important than relative humidity regarding the color responses. Strong correlations between total color difference and both modulus of elasticity and bending strength were found. Thus, the color parameters can be estimated quantitatively and used as a prediction of wood strength.

The Effect of Aging Heat Treatment on the Microstructure and Mechanical Properties of 10Cr20Ni25Mo1.5NbN Austenitic Steel

2016 ◽  
Vol 35 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Zhiyuan Liang ◽  
Wanhua Sha ◽  
Qinxin Zhao ◽  
Chongbin Wang ◽  
Jianyong Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Austenitic Steel ◽  
Treatment Time ◽  
Aging Treatment ◽  
Secondary Phases ◽  
Aging Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
The Impact

AbstractThe effect of aging heat treatment on the microstructure and mechanical properties of 10Cr20Ni25Mo1.5NbN austenitic steel was investigated in this article. The microstructure was characterized by scanning electron microscopy, energy dispersive spectrometry and transmission electron microscopy. Results show that the microstructure of 10Cr20Ni25Mo1.5NbN austenitic is composed of austenite. This steel was strengthened by precipitates of secondary phases that were mainly M23C6 carbides and NbCrN nitrides. As aging treatment time increased, the tensile strength first rose (0–3,000 h) and then fell (3,000–5,000 h) due to the decrease of high density of dislocations. The impact absorbed energy decreased sharply, causing the sulfides to precipitate at the grain boundary. Therefore, the content of sulfur should be strictly controlled in the steelmaking process.

Permanent Mold Casting Practice and Microstructure and Mechanical Properties of Thin-Sectioned ADI Casting

2007 ◽  
Vol 26-28 ◽  
pp. 531-534
Author(s):  
B.M. Moon ◽  
Bong Hwan Kim ◽  
Je Sik Shin ◽  
Sang Mok Lee
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Ductile Cast Iron ◽  
Treatment Temperature ◽  
Chemical Compositions ◽  
Permanent Mold ◽  
Permanent Mold Casting ◽  
Treatment Practice ◽  
Mold Casting ◽  
Si Content

For thin-walled casting development of austempered ductile iron (ADI), permanent mold casting and accompanied heat treatment practice were systematically investigated to suppress and/or remove chill defects of ductile cast iron (DCI) with various thickness of 2 to 9 mm and to ensure mechanical properties of the final ADI casting. Si content was increased up to 3.8% to reduce the chill formation tendency under a high cooling rate. The residual Mg content remarkably affected the nodule count, while the nodule size and spherodization were proven to have weak relationships. Austenitizing process followed by austempering was very sensitive to chemical compositions (Si and Sn) and heat treatment temperature. As a practical application, the steel bar coupler for a structural frame was tried to produce without subsequent machining.

Novel Polyaspartic Ester Polyureas Based on Flexible Polyaspartic Ester

2011 ◽  
Vol 197-198 ◽  
pp. 1294-1298
Author(s):  
Ping Lu ◽  
Wei Bo Huang ◽  
Xue Qiang Ma ◽  
Xu Dong Liu
Keyword(s):  
Mechanical Properties ◽  
Molecular Weight ◽  
Hydrogen Bonding ◽  
Molecular Weight Distribution ◽  
Michael Addition ◽  
Weight Distribution ◽  
Addition Reaction ◽  
Chain Extender ◽  
Michael Addition Reaction ◽  
Ft Ir

New polyaspartic ester (PAE) chain extender named PAE-f was prepared via two steps of Michael addition reactions:(1) Michael addition reaction between 4,4’-methylenebis(2-methyl cyclohexyl amine) (Laromin C260) and excessive dialkyl maleates（DEF）; (2) The Michael addition reaction of the residual dialkyl maleates of step (1) with polyester polyamine Jeffamine D230. The two-steps method proposed could reduce the reaction time in comparison with the current one step Michael addition reaction method, thus satisfying the industrialized production. New PAE based polyureas were synthesized by reacting the PAE-f chain extender with aliphatic polyisocyanates 4,4’-diisocyanato dicyclohexylmethane (H12MDI) / polyester polyamine Jeffamine D2000 prepolymer at room temperature. FT-IR and GPC were employed to characterize the new PAE prepared, and the morphology, molecular weight distribution and mechanical properties of the prepared PAE based polyureas were investigated by means of FT-IR and GPC. The FT-IR results indicated that the hydrogen bonding degree of amidogen groups in hard segments of the prepared polyureas were high, the length of hydrogen bonding were 0.305nm～0.306nm. The GPC experimental results show that the weight average molecular weight of the PAE-f based polyureas were 4.95×104～6.05×104,Mw/Mn were 1.65～1.97, the molecular weight distribution were relatively narrow. The mechanical properties demonstrated that the tensile strength were 14.7～22.5MPa, Elongation at break were 306～511%, Yang’s modulus were 67～127MPa, Shore A hardness were 64～83. The mechanical properties confirmed that the polyureas based on PAE-f were kinds of elastomeric materials with satisfied flexibility, strength, module and hardness.

Characteristics of Lithium Polysilicate Electrolyte Synthesized by Sol-Gel Processing

2007 ◽  
Vol 124-126 ◽  
pp. 1031-1034
Author(s):  
Bong Soo Jin ◽  
Bok Ki Min ◽  
Chil Hoon Doh
Keyword(s):  
Heat Treatment ◽  
Acid Treatment ◽  
Treatment Time ◽  
Sol Gel ◽  
Silicate Solution ◽  
Treatment Temperature ◽  
Lithium Silicate ◽  
Treatment Conditions ◽  
Xrd Patterns ◽  
Si Wafer

To find out suitable Si surface treatment and heat treatment conditions, acid treatment of Si wafer was done for lithium polysilicate electrolyte coating on Si wafer. In case of HCl treatment, the wet angle of a sample is 30o, which is the smallest wet angle of other acid in this experiment. Acid treatment time is 10 min, which is no more change of wet angle. Lithium polysilicate electrolyte was synthesized by hydrolysis and condensation of lithium silicate solution using perchloric acid. Thermal analysis of lithium polysilicate electrolyte shows the weight loss of ~23 % between 400 and 500 , which is due to the decomposition of LiClO4. The XRD patterns of the obtained lithium polysilicate electrolyte also show the decrement of LiClO4 peak at 400 . The optimum heat treatment temperature is below 400 , which is the suitable answer for lithium polysilicate electrolyte.

The Change of Mechanical Properties for Anodic Aluminum Oxide by Heat Treatment

2006 ◽  
Vol 317-318 ◽  
pp. 323-326 ◽  
Author(s):  
D.J. Park ◽  
S.H. Kim ◽  
J.H. Lee ◽  
Seong Hee Lee ◽  
Yong Ho Choa
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mechanical Property ◽  
Oxalic Acid ◽  
Aluminum Oxide ◽  
Crystalline Phase ◽  
Anodic Aluminum Oxide ◽  
Treatment Temperature ◽  
Microstructure Change ◽  
Anodic Aluminum

Anodic aluminum oxide (AAO) was prepared in three types of aqueous solutions with various applied voltage. The mechanical property of AAO prepared in different electrolyte was investigated and hardness was increased on account of the increase of the thickness between pores. The mechanical property and microstructure change of AAO prepared in oxalic acid at 40V was investigated by heat treatment. AAO prepared in oxalic acid at 40V was transformed from amorphous to crystalline phase by heat treatment above 800oC and hardness was increased about 2.6 times with increase of heat treatment temperature.

Low-temperature thermal pretreatment process for recycling inner core of spent lithium iron phosphate batteries

2020 ◽  
pp. 0734242X2095740
Author(s):  
Haijun Bi ◽  
Huabing Zhu ◽  
Lei Zu ◽  
Yong Gao ◽  
Song Gao ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Low Temperature ◽  
Heat Treatment Temperature ◽  
Lithium Iron Phosphate ◽  
Inner Core ◽  
Treatment Time ◽  
Iron Phosphate ◽  
Treatment Temperature ◽  
Heat Treatment Time ◽  
Physicochemical Changes

Spent lithium iron phosphate (LFP) batteries contain abundant strategic lithium resources and are thus considered attractive secondary lithium sources. However, these batteries may contaminate the environment because they contain hazardous materials. In this work, a novel process involving low-temperature heat treatment is used as an alternative pretreatment method for recycling spent LFP batteries. When the temperature reaches 300°C, the dissociation effect of the anode material gradually improves with heat treatment time. At the heat treatment time of 120 minutes, an electrode material can be dissociated. The extension of heat treatment time has a minimal effect on quality loss. The physicochemical changes in thermally treated solid cathode and anode materials are examined through scanning electron microscopy with energy-dispersive X-ray spectroscopy. The heat treatment results in the complete separation of the materials from aluminium foil without contamination. The change in heat treatment temperature has a small effect on the quality of LFP material shedding. When the heat treatment temperature reaches 300°C and the time reaches 120 minutes, heat treatment time increases, and the yield of each particle size is stable and basically unchanged. The method can be scaled up and may reduce environmental pollution due to waste LFP batteries.

Sign in / Sign up

Export Citation Format

Share Document