scholarly journals Study on Pore Structure and Sulfur Fixation Characteristics of Alkali Industrial Waste

2011 ◽  
Vol 194-196 ◽  
pp. 716-721 ◽  
Author(s):  
Gai Ju Zhao ◽  
Feng Jiao Yin ◽  
Jie Li ◽  
Xuan You Li
Keyword(s):  
Pore Structure ◽  
Significant Contribution ◽  
Mercury Porosimetry ◽  
Structure Characteristics ◽  
Initial Stage ◽  
Effective Aperture ◽  
Higher Temperature ◽  
Lower Temperature ◽  
Sulfur Fixation ◽  
Calcium Utilization

Pore structure of experiment alkali waste were investigated by Mercury Porosimetry, the influence of pore structure characteristics on their sulfur fixation performance were discussed, it can be found that little pores make a significant contribution to calcium utilization in the initial stage of reaction and at lower temperature, while bigger pores take effect in the later stage and at higher temperature, the range of effective aperture are different at different temperature, which respectively are from 0.005μm to 0.02μm at temperature from 1123K to 1223K and from 0.2μm to 0.3μm at temperature from 1223K to 1323K, the more pore in range of effective aperture, the better the sulfur fixation performance.

Evaluation Shale Pore Size Spectrum Using Mercury Porosimetry and Nitrogen Adsorption Experiment: A Case Study from the Longtan Formation Shale, Southeastern Hunan, China

2014 ◽  
Vol 962-965 ◽  
pp. 34-40
Author(s):  
Ning Yang ◽  
Shu Heng Tang ◽  
Song Hang Zhang ◽  
Jun Jie Yi
Keyword(s):  
Pore Structure ◽  
Parallel Plate ◽  
Mercury Porosimetry ◽  
Nitrogen Adsorption ◽  
Size Spectrum ◽  
Adsorption Experiment ◽  
Structure Characteristics ◽  
Gas Shales ◽  
Strong Ability

Gas shales have a complex pore structure. Using mercury porosimetry and nitrogen adsorption experiment on shale of Longtan Formation in southeastern of Hunan, the pore structure characteristics were contrast analyzed, influencing factors and its impact on reservoir-forming were discussed. Longtan Formation shale is composed of nanopores, include the cylinder pores with two ends open and parallel-plate pores with four sides open. The efficiency of mercury ejection ranges 31.45%~63.82%, 51.94% on average, pores uniformity is well. The size of nanopores is 5~30nm, taking up 94.74% of the total volume and 98.08% of specific surface area. Brittle minerals content is high, as an important parameter influencing pore development. The nanopores have a strong ability to absorb gas, methane molecule exist in a structured way.

scholarly journals Sprouting of Sorghum (Sorghum bicolor [L.] Moench): Effect of Drying Treatment on Protein and Starch Features

Foods ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 407 ◽  
Author(s):  
Mia Marchini ◽  
Alessandra Marti ◽  
Claudia Folli ◽  
Barbara Prandi ◽  
Tommaso Ganino ◽  
...  
Keyword(s):  
Food Production ◽  
Cost Effective ◽  
High Exposure ◽  
Effective Technology ◽  
Drying Treatment ◽  
Higher Temperature ◽  
Lower Temperature ◽  
The One ◽  
Drying Conditions ◽  
Sorghum Bicolor L

The nutritional and physicochemical properties of sorghum proteins and starch make the use of this cereal for food production challenging. Sprouting is a cost-effective technology to improve the nutritional and functional profile of grains. Two drying treatments were used after sorghum sprouting to investigate whether the drying phase could improve the protein and starch functionalities. Results showed that the drying treatment at lower temperature/longer time (40 °C for 12 h) extended the enzymatic activity that started during sprouting compared to the one performed at higher temperature/shorter time (50 °C for 6 h). An increased protein hydrolysis and water- and oil-holding capacity were found in the flour obtained by the former treatment. Higher protein matrix hydrolysis caused high exposure of starch to enzymes, thus increasing its digestibility, while worsening the technological functionality. Overall, modulating drying conditions could represent a further way, in addition to sprouting, to improve sorghum flour’s nutritional profile.

Development of pore structure characteristics of a weathered crust elution-deposited rare earth ore during leaching with different valence cations

2021 ◽  
Vol 201 ◽  
pp. 105579
Author(s):  
Lingbo Zhou ◽  
Xiaojun Wang ◽  
Chengguang Huang ◽  
Hao Wang ◽  
Huachang Ye ◽  
...  
Keyword(s):  
Rare Earth ◽  
Pore Structure ◽  
Structure Characteristics ◽  
Weathered Crust

MICROSTRUCTURAL EVOLUTION OF Al-Cu-Mg-Ag ALLOY WITH TRACE Zr ADDITION DURING TWO-STEP HOMOGENIZATION

2009 ◽  
Vol 23 (06n07) ◽  
pp. 855-862 ◽  
Author(s):  
FEIYUE MA ◽  
ZHIYI LIU
Keyword(s):  
Melting Point ◽  
Grain Boundaries ◽  
Microstructural Evolution ◽  
Cast Alloy ◽  
Scanning Calorimetry ◽  
Zr Addition ◽  
Homogenization Time ◽  
The Matrix ◽  
Higher Temperature ◽  
Lower Temperature

The microstructural evolution in an Al - Cu - Mg - Ag alloy with trace Zr addition during homogenization treatment was characterized by Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray Spectroscopy (EDS). It was shown that the low-melting-point phase segregating toward grain boundaries is Al 2 Cu , with a melting point of 523.52°C. A two-step homogenization process was employed to optimize the microstructure of the as-cast alloy, during which the alloy was first homogenized at a lower temperature, then at a higher temperature. After homogenized at 420°C for 6 h, Al 3 Zr particles were finely formed in the matrix. After that, when the alloy was homogenized at an elevated temperature for a longer time, i.e., 515°C for 24 h, most of the precipates at the grain boundaries were removed. Furthermore, the dispersive Al 3 Zr precipitates were retained, without coarsening greatly in the final homogenization step. A kinetics model is employed to predict the optimal homogenization time at a given temperature theoretically, and it confirms the result in present study, which is 420°C/6h+515°C/24h.

Research on the Wire Drawing Die Pass Parameter Calculation Based on the Least Square Algorithm

2012 ◽  
Vol 591-593 ◽  
pp. 850-853
Author(s):  
Huai Xing Wen ◽  
Yong Tao Yang
Keyword(s):  
Pore Structure ◽  
Least Squares ◽  
Least Squares Method ◽  
Piecewise Linear ◽  
Wire Drawing ◽  
Least Square ◽  
Structure Characteristics ◽  
Drawing Die ◽  
The Wire ◽  
Drawing Dies

Drawing Dies meter A / D acquisition module will be collected from the mold hole contour data to draw a curve in Matlab. According to the mold pore structure characteristics of the curve, the initial cut-off point of each part of contour is determined and iteratived optimization to find the best cut-off point, use the least squares method for fitting piecewise linear and fitting optimization to find the function of the various parts of the curve function, finally calculate the pass parameters of drawing mode. Parameters obtained compare with the standard mold, both of errors are relatively small that prove the correctness of the algorithm. Also a complete algorithm flow of pass parameters is designed, it can fast and accurately measure the wire drawing die hole parameters.

scholarly journals Research on the Static Recrystallization and Precipitation Behaviors of a V-N Microalloyed Steel

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Baochun Zhao ◽  
Tan Zhao ◽  
Guiyan Li ◽  
Qiang Lu
Keyword(s):  
Static Recrystallization ◽  
Microalloyed Steel ◽  
Time Interval ◽  
Main Role ◽  
Recrystallization Process ◽  
Compression Tests ◽  
Double Compression ◽  
Higher Temperature ◽  
Lower Temperature ◽  
Temperature Strain

Double compression tests were performed on a Gleeble-3800 thermomechanical simulator to study the softening behaviors of deformed austenite in a V-N microalloyed steel. The static recrystallization volume fractions were calculated by stress offset method, and the kinetic model of static recrystallization was constructed. The effects of temperature, strain, and time interval on the softening behaviors were analyzed, and the interactions between precipitation and recrystallization were discussed. The results show that the softening behaviors of the deformed austenite at lower temperature or higher temperature are markedly different. At the temperature of 850°C or 800°C, pinning effects of the precipitates play the main role, and the recrystallization process is inhibited, which leads to the formation of plateaus in the softening curves. An increase in strain promotes the precipitation and recrystallization processes while reduces the inhibition effect of precipitation on recrystallization as well.

Effects of Sr Addition on Mechanical Properties and Microstructure of Mg-6Al Magnesium Alloy

2011 ◽  
Vol 686 ◽  
pp. 120-124
Author(s):  
Jin Ping Fan ◽  
She Bin Wang ◽  
Bing She Xu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Strengthening Mechanism ◽  
Microstructure And Mechanical Properties ◽  
Higher Temperature ◽  
Lower Temperature

The effects of Sr addition on the mechanical properties and microstructure of Mg-6Al mag- nesium alloy both at 25 °C and at 175 °C were investigated by means of OM, SEM and EDS and XRD. Upon the Sr addition of 2%, the tensile strength was increased by 7.2% to 184.4MPa at 25 °C, while it was increased by 30% to 155.4MPa at 175 °C. The strengthening mechanism of Mg-6Al-xSr at lower temperature (25 °C) was different from that at higher temperature (175°C). The results show that the addition of strontium effectively improved the microstructure and mechanical properties of magnesium alloy.

Effect of walnut shell ash on pore structure characteristics during Zhundong coal sintering

2021 ◽  
Vol 221 ◽  
pp. 106923
Author(s):  
Hao Zhou ◽  
Jiawei Luo ◽  
Zhaowen Wang ◽  
Mengting Ji ◽  
Mingrui Zhang
Keyword(s):  
Pore Structure ◽  
Walnut Shell ◽  
Structure Characteristics ◽  
Zhundong Coal
Sign in / Sign up

Export Citation Format

Share Document