scholarly journals Sprouting of Sorghum (Sorghum bicolor [L.] Moench): Effect of Drying Treatment on Protein and Starch Features

Foods ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 407 ◽  
Author(s):  
Mia Marchini ◽  
Alessandra Marti ◽  
Claudia Folli ◽  
Barbara Prandi ◽  
Tommaso Ganino ◽  
...  
Keyword(s):  
Food Production ◽  
Cost Effective ◽  
High Exposure ◽  
Effective Technology ◽  
Drying Treatment ◽  
Higher Temperature ◽  
Lower Temperature ◽  
The One ◽  
Drying Conditions ◽  
Sorghum Bicolor L

The nutritional and physicochemical properties of sorghum proteins and starch make the use of this cereal for food production challenging. Sprouting is a cost-effective technology to improve the nutritional and functional profile of grains. Two drying treatments were used after sorghum sprouting to investigate whether the drying phase could improve the protein and starch functionalities. Results showed that the drying treatment at lower temperature/longer time (40 °C for 12 h) extended the enzymatic activity that started during sprouting compared to the one performed at higher temperature/shorter time (50 °C for 6 h). An increased protein hydrolysis and water- and oil-holding capacity were found in the flour obtained by the former treatment. Higher protein matrix hydrolysis caused high exposure of starch to enzymes, thus increasing its digestibility, while worsening the technological functionality. Overall, modulating drying conditions could represent a further way, in addition to sprouting, to improve sorghum flour’s nutritional profile.

scholarly journals Editor in Chief Commentary: Water - Recognizing the Indigenous Perspective

2012 ◽  
Vol 3 (3) ◽  
Author(s):  
Jerry P. White
Keyword(s):  
Indigenous Peoples ◽  
Environmental Sustainability ◽  
Cost Effective ◽  
Indigenous Communities ◽  
Special Issue ◽  
Safe Water ◽  
Utilization Of Technology ◽  
The Social ◽  
Effective Technology ◽  
The One

Indigenous peoples have, since time immemorial, understood that water is central to the cycles of life. Yet, as many of the articles in this special issue on water in Indigenous communities point out, Indigenous peoples have real problems accessing safe water. Why? Indigenous peoples have always cared for the water and followed practices that, depending on their geography, varied by season to protect and conserve fresh safe water. They have celebrated it as witnessed by the ceremony and language used. Colonial practices have disrupted the care and knowledge passing in Indigenous communities. Cost-effective technology exists to deliver safe water to Indigenous communities. The issue is that utilization of technology and environmental sustainability rest on the social determinants of safe water. From a policy perspective, this means we have to look outside of Western technological solutions and come to listen to the other ‘story’ - the one that emanates from Indigenous Traditional Knowledge.

Improving Doping Efficiency of P+ Implanted Ions in 4H-SiC

2011 ◽  
Vol 679-680 ◽  
pp. 393-396 ◽  
Author(s):  
Roberta Nipoti ◽  
Anindya Nath ◽  
Stefano Cristiani ◽  
Michele Sanmartin ◽  
Mulpuri V. Rao
Keyword(s):  
Heating System ◽  
Annealing Process ◽  
Electrical Activation ◽  
High Annealing ◽  
Microwave Furnace ◽  
Higher Temperature ◽  
Lower Temperature ◽  
The One ◽  
Post Implantation ◽  
Very High

An inductively heated furnace and an ultra-fast microwave heating system have been used for performing post implantation annealing processes of P+ implanted semi-insulating <0001> 4H SiC at 1800-1950°C for 5 min and 2000-2050°C for 30 s, respectively. Very high P+ implantation fluences in the range 71019 81020 cm-3 have been studied. The annealing processes in the inductive furnace and the one at the lower temperature in the microwave furnace show a saturation in the efficiency of the electrical activation of the implanted P+ that is bypassed by the microwave annealing process at the higher temperature. The measured electron mobility values versus electron density are elevated in all the studied samples and for every post implantation annealing process. This has been ascribed to an elevated implanted crystal recovery due to the very high annealing temperatures > 1800°C.

scholarly journals Effect of temperature on population growth of copepod, Euterpina acutifrons

2020 ◽  
Vol 4 (1) ◽  
pp. 57-61
Author(s):  
Sitti Raehanah Muhamad Shaleh
Keyword(s):  
Population Growth ◽  
Total Population ◽  
Effect Of Temperature ◽  
Optimum Temperature ◽  
Dark Cycle ◽  
Higher Temperature ◽  
Lower Temperature ◽  
The One ◽  
Population Counts ◽  
Euterpina Acutifrons

This study was aimed at determining the optimum temperature for culturing the copepod, Euterpina acutifrons. The trial was conducted for 10 days in chambers at temperatures of 25⁰C, 27⁰C, 29⁰C and 31⁰C. Ten adult individuals of the copepod were randomly collected and placed into three replicate experimental flasks for each treatment. Throughout the trial, the salinity, light intensity, and photoperiod were maintained at 30 ±2psu, 100molm-2s-1 and 12:12 light-dark cycle, respectively. The copepods were fed with 80,000cell/ml Isochrysis sp. daily. At the end of the trial, the total numbers of E. acutifrons nauplii, copepodites and adults were determined and counted using Sedgwick-Rafter. The highest population was found at 27⁰C with mean total population of 800±100 individuals from an initial of 10 individuals. This was followed by those reared at 25⁰C and 29⁰C where the population counts were 700±100 individuals and 367±115 individuals, respectively. At the 31⁰C, all the copepod specimens were found dead on day 5th. Statistical analysis showed that the temperature had a significant effect (P<0.05) on the population growth of the copepod. The population of nauplii was higher in lower temperature (25⁰C) set compared to the one at higher temperature (29⁰C). However, the copepodite number was greater at 27⁰C. Growth of the copepod was highest at 27⁰C (0.438K) followed by sets at 25⁰C (0.425K) and 29⁰C (0.361K). Based on the results of this analysis, it is suggested to culture copepod at temperature 25⁰C for nauplii production and 27⁰C for producing more copepodites.

Nucleation of Disorder in Fe3Al Alloys

1967 ◽  
Vol 25 ◽  
pp. 312-313
Author(s):  
P. R. Swann ◽  
W. R. Duff ◽  
R. M. Fisher
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Annealing Temperature ◽  
Antiphase Domain ◽  
Effect Of Temperature ◽  
Domain Structures ◽  
Transmission Electron ◽  
Domain Boundaries ◽  
Higher Temperature ◽  
The One

Recently we have investigated the phase equilibria and antiphase domain structures of Fe-Al alloys containing from 18 to 50 at.% Al by transmission electron microscopy and Mössbauer techniques. This study has revealed that none of the published phase diagrams are correct, although the one proposed by Rimlinger agrees most closely with our results to be published separately. In this paper observations by transmission electron microscopy relating to the nucleation of disorder in Fe-24% Al will be described. Figure 1 shows the structure after heating this alloy to 776.6°C and quenching. The white areas are B2 micro-domains corresponding to regions of disorder which form at the annealing temperature and re-order during the quench. By examining specimens heated in a temperature gradient of 2°C/cm it is possible to determine the effect of temperature on the disordering reaction very precisely. It was found that disorder begins at existing antiphase domain boundaries but that at a slightly higher temperature (1°C) it also occurs by homogeneous nucleation within the domains. A small (∼ .01°C) further increase in temperature caused these micro-domains to completely fill the specimen.

The Formability and Elongation of Aluminum Alloys AA5083 and AA3003 for Micro-Truss Sandwiches Manufacturing

2020 ◽  
Vol 38 (9A) ◽  
pp. 1396-1405
Author(s):  
Arwa F. Tawfeeq ◽  
Matthew R. Barnett
Keyword(s):  
Aluminum Alloy ◽  
Strain Rate ◽  
Cost Effective ◽  
Tensile Tests ◽  
Truss Structures ◽  
High Quality ◽  
Trade Off ◽  
Clad Layer ◽  
Higher Temperature ◽  
Different Shapes

The development in the manufacturing of micro-truss structures has demonstrated the effectiveness of brazing for assembling these sandwiches, which opens new opportunities for cost-effective and high-quality truss manufacturing. An evolving idea in micro-truss manufacturing is the possibility of forming these structures in different shapes with the aid of elevated temperature. This work investigates the formability and elongation of aluminum alloy sheets typically used for micro-truss manufacturing, namely AA5083 and AA3003. Tensile tests were performed at a temperature in the range of 25-500 ○C and strain rate in the range of 2x10-4 -10-2 s-1. The results showed that the clad layer in AA3003 exhibited an insignificant effect on the formability and elongation of AA3003. The formability of the two alloys was improved significantly with values of m as high as 0.4 and 0.13 for AA5083 and AA3003 at 500 °C. While the elongation of both AA5083 and AA3003 was improved at a higher temperature, the elongation of AA5083 was inversely related to strain rate. It was concluded that the higher the temperature is the better the formability and elongation of the two alloys but at the expense of work hardening. This suggests a trade-off situation between formability and strength. 

3D printing in pharmacy

2020 ◽  
pp. 58-60
Author(s):  
Yuliya Prozherina ◽  
Keyword(s):  
3D Printing ◽  
Cost Effective ◽  
Drug Market ◽  
Dosage Forms ◽  
Fixed Dose ◽  
Major Step ◽  
Combination Drugs ◽  
Effective Technology ◽  
Dose Combination ◽  
Research Stage

3D printing of drugs is an innovative and cost-effective technology, which is a major step towards personalized medicine. This technology can be used for the development of controlled-release drugs; fixed-dose combination drugs, as well as for the creation of orodispersible dosage forms. The global 3D drug market is still largely at the research stage, but its rapid growth is expected in the coming decade [1].

MICROSTRUCTURAL EVOLUTION OF Al-Cu-Mg-Ag ALLOY WITH TRACE Zr ADDITION DURING TWO-STEP HOMOGENIZATION

2009 ◽  
Vol 23 (06n07) ◽  
pp. 855-862 ◽  
Author(s):  
FEIYUE MA ◽  
ZHIYI LIU
Keyword(s):  
Melting Point ◽  
Grain Boundaries ◽  
Microstructural Evolution ◽  
Cast Alloy ◽  
Scanning Calorimetry ◽  
Zr Addition ◽  
Homogenization Time ◽  
The Matrix ◽  
Higher Temperature ◽  
Lower Temperature

The microstructural evolution in an Al - Cu - Mg - Ag alloy with trace Zr addition during homogenization treatment was characterized by Differential Scanning Calorimetry (DSC), Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray Spectroscopy (EDS). It was shown that the low-melting-point phase segregating toward grain boundaries is Al 2 Cu , with a melting point of 523.52°C. A two-step homogenization process was employed to optimize the microstructure of the as-cast alloy, during which the alloy was first homogenized at a lower temperature, then at a higher temperature. After homogenized at 420°C for 6 h, Al 3 Zr particles were finely formed in the matrix. After that, when the alloy was homogenized at an elevated temperature for a longer time, i.e., 515°C for 24 h, most of the precipates at the grain boundaries were removed. Furthermore, the dispersive Al 3 Zr precipitates were retained, without coarsening greatly in the final homogenization step. A kinetics model is employed to predict the optimal homogenization time at a given temperature theoretically, and it confirms the result in present study, which is 420°C/6h+515°C/24h.

scholarly journals Research on the Static Recrystallization and Precipitation Behaviors of a V-N Microalloyed Steel

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
Baochun Zhao ◽  
Tan Zhao ◽  
Guiyan Li ◽  
Qiang Lu
Keyword(s):  
Static Recrystallization ◽  
Microalloyed Steel ◽  
Time Interval ◽  
Main Role ◽  
Recrystallization Process ◽  
Compression Tests ◽  
Double Compression ◽  
Higher Temperature ◽  
Lower Temperature ◽  
Temperature Strain

Double compression tests were performed on a Gleeble-3800 thermomechanical simulator to study the softening behaviors of deformed austenite in a V-N microalloyed steel. The static recrystallization volume fractions were calculated by stress offset method, and the kinetic model of static recrystallization was constructed. The effects of temperature, strain, and time interval on the softening behaviors were analyzed, and the interactions between precipitation and recrystallization were discussed. The results show that the softening behaviors of the deformed austenite at lower temperature or higher temperature are markedly different. At the temperature of 850°C or 800°C, pinning effects of the precipitates play the main role, and the recrystallization process is inhibited, which leads to the formation of plateaus in the softening curves. An increase in strain promotes the precipitation and recrystallization processes while reduces the inhibition effect of precipitation on recrystallization as well.

Effects of Sr Addition on Mechanical Properties and Microstructure of Mg-6Al Magnesium Alloy

2011 ◽  
Vol 686 ◽  
pp. 120-124
Author(s):  
Jin Ping Fan ◽  
She Bin Wang ◽  
Bing She Xu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Strengthening Mechanism ◽  
Microstructure And Mechanical Properties ◽  
Higher Temperature ◽  
Lower Temperature

The effects of Sr addition on the mechanical properties and microstructure of Mg-6Al mag- nesium alloy both at 25 °C and at 175 °C were investigated by means of OM, SEM and EDS and XRD. Upon the Sr addition of 2%, the tensile strength was increased by 7.2% to 184.4MPa at 25 °C, while it was increased by 30% to 155.4MPa at 175 °C. The strengthening mechanism of Mg-6Al-xSr at lower temperature (25 °C) was different from that at higher temperature (175°C). The results show that the addition of strontium effectively improved the microstructure and mechanical properties of magnesium alloy.

Sign in / Sign up

Export Citation Format

Share Document