Theorical Analysis of Leakage in High Pressure Pipe Using Acoustic Emission Method

2012 ◽  
Vol 445 ◽  
pp. 917-922 ◽  
Author(s):  
Saman Davoodi ◽  
Amir Mostafapour
Keyword(s):  
High Pressure ◽  
Acoustic Emission ◽  
Degrees Of Freedom ◽  
Oil And Gas ◽  
Pipe Wall ◽  
Leak Detection ◽  
Stress Waves ◽  
Motion Equation ◽  
Non Linear ◽  
Acoustic Emission Test

Leak detection is one of the most important problems in the oil and gas pipelines. Where it can lead to financial losses, severe human and environmental impacts. Acoustic emission test is a new technique for leak detection. Leakage in high pressure pipes creates stress waves resulting from localized loss of energy. Stress waves are transmitted through the pipe wall which will be recorded by using acoustic sensor or accelerometer installed on the pipe wall. Knowledge of how the pipe wall vibrates by acoustic emission resulting from leakage is a key parameter for leak detection and location. In this paper, modeling of pipe vibration caused by acoustic emission generated by escaping of fluid has been done. Donnells non linear theory for cylindrical shell is used to deriving of motion equation and simply supported boundary condition is considered. By using Galerkin method, the motion equation has been solved and a system of non linear equations with 6 degrees of freedom is obtained. To solve these equations, ODE tool of MATLAB software and Rung-Kuta numerical method is used and pipe wall radial displacement is obtained. For verification of this theory, acoustic emission test with continues leak source has been done. Vibration of wall pipe was recorded by using acoustic emission sensors. For better analysis, Fast Fourier Transform (FFT) was taken from theoretical and experimental results. By comparing the results, it is found that the range of frequencies which carried the most amount of energy is same which expresses the affectivity of the model.

Pipeline Leak Detection System for Oil and Gas Flowlines

1997 ◽  
Vol 119 (1) ◽  
pp. 105-109 ◽  
Author(s):  
J. M. Rajtar ◽  
R. Muthiah
Keyword(s):  
Acoustic Emission ◽  
Oil And Gas ◽  
Production Systems ◽  
Detection System ◽  
Leak Detection ◽  
Production Costs ◽  
Closed Field ◽  
Two Phase ◽  
Expected Performance ◽  
Potential Applications

Petroleum fluids in production systems are frequently transported by surface steel pipelines of low diameter working at low pressures and under a two-phase flow regime. These pipelines operate without permanent, continuous supervision for leaks. The leaked volume is usually high before the leak is noticed and stopped. High leak volumes pollute the environment and increase production costs. This paper describes the expected performance of the acoustic emission leak detection system for low pressure flowlines in oil and gas gathering installations. The developed system detects acoustic emission signals generated by leaks. Specific features of the system are discussed. The system was tested in a closed field scale two-phase flowloop. Example results of tests are reported. The paper is completed with conclusions and discussion of potential applications of the system.

scholarly journals Pressure-induced Jahn-Teller Switch in the Homoleptic Hybrid Perovskite [(CH3)2NH2]Cu(HCOO)3: Orbital Reordering by Unconventional Degrees of Freedom

2021 ◽  
Author(s):  
Rebecca Scatena ◽  
Michał Andrzejewski ◽  
Roger D Johnson ◽  
Piero Macchi
Keyword(s):  
Phase Transition ◽  
High Pressure ◽  
Coordination Polymer ◽  
Degrees Of Freedom ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hybrid Perovskite ◽  
Jahn Teller

Through in-situ, high-pressure x-ray diffraction experiments we have shown that the homoleptic perovskite-like coordination polymer [(CH3)2NH2]Cu(HCOO)3 undergoes a pressure-induced orbital reordering phase transition above 5.20 GPa. This transition is distinct...

In-situ high-pressure study of the ordered phase of ethyl propionate

2007 ◽  
Vol 63 (1) ◽  
pp. 111-117 ◽  
Author(s):  
Roman Gajda ◽  
Andrzej Katrusiak
Keyword(s):  
High Pressure ◽  
Degrees Of Freedom ◽  
Molecular Volume ◽  
Ethyl Propionate ◽  
Intermolecular Contacts ◽  
High Pressure Study ◽  
Pressure Phase ◽  
Three Degrees Of Freedom ◽  
Volume Difference

Ethyl propionate, C5H10O2 (m.p. 199 K), has been in-situ pressure-frozen and its structure determined at 1.34, 1.98 and 2.45 GPa. The crystal structure of the new high-pressure phase (denoted β) is different from phase α obtained by lowering the temperature. The freezing pressure of ethyl propionate at 296 K is 1.03 GPa. The molecule assumes an extended chain s-trans–trans–trans conformation, only slightly distorted from planarity. The closest intermolecular contacts in both phases are formed between carbonyl O and methyl H atoms; however, the ethyl-group H atoms in phase β form no contacts shorter than 2.58 Å. A considerable molecular volume difference of 24.2 Å3 between phases α and β can be rationalized in terms of degrees of freedom of molecules arranged into closely packed structures: the three degrees of freedom allowed for rearrangements of molecules confined to planar sheets in phase α, but are not sufficient for obtaining a densely packed pattern.

scholarly journals Monitoring geological storage of CO2: a new approach

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Manzar Fawad ◽  
Nazmul Haque Mondol
Keyword(s):  
Oil And Gas ◽  
Synthetic Data ◽  
Leak Detection ◽  
Hydrocarbon Exploration ◽  
Water Flooding ◽  
Storage Site ◽  
Gas Reservoirs ◽  
New Approach ◽  
Coal Beds ◽  
Spatial Coverage

AbstractGeological CO2 storage can be employed to reduce greenhouse gas emissions to the atmosphere. Depleted oil and gas reservoirs, deep saline aquifers, and coal beds are considered to be viable subsurface CO2 storage options. Remote monitoring is essential for observing CO2 plume migration and potential leak detection during and after injection. Leak detection is probably the main risk, though overall monitoring for the plume boundaries and verification of stored volumes are also necessary. There are many effective remote CO2 monitoring techniques with various benefits and limitations. We suggest a new approach using a combination of repeated seismic and electromagnetic surveys to delineate CO2 plume and estimate the gas saturation in a saline reservoir during the lifetime of a storage site. This study deals with the CO2 plume delineation and saturation estimation using a combination of seismic and electromagnetic or controlled-source electromagnetic (EM/CSEM) synthetic data. We assumed two scenarios over a period of 40 years; Case 1 was modeled assuming both seismic and EM repeated surveys were acquired, whereas, in Case 2, repeated EM surveys were taken with only before injection (baseline) 3D seismic data available. Our results show that monitoring the CO2 plume in terms of extent and saturation is possible both by (i) using a repeated seismic and electromagnetic, and (ii) using a baseline seismic in combination with repeated electromagnetic data. Due to the nature of the seismic and EM techniques, spatial coverage from the reservoir's base to the surface makes it possible to detect the CO2 plume’s lateral and vertical migration. However, the CSEM low resolution and depth uncertainties are some limitations that need consideration. These results also have implications for monitoring oil production—especially with water flooding, hydrocarbon exploration, and freshwater aquifer identification.

An XYZ Parallel Kinematic Flexure Mechanism With Geometrically Decoupled Degrees of Freedom

2011 ◽  
Author(s):  
Shorya Awtar ◽  
John Ustick ◽  
Shiladitya Sen
Keyword(s):  
Degrees Of Freedom ◽  
Element Analysis ◽  
Motion Direction ◽  
Form Analysis ◽  
Flexure Mechanism ◽  
Non Linear ◽  
Decoupled Motion ◽  
Motion Range ◽  
Parallel Kinematic ◽  
Cross Axis

We present the constraint-based design of a novel parallel kinematic flexure mechanism that provides highly decoupled motions along the three translational directions (X, Y, and Z) and high stiffness along the three rotational directions (θx, θy, and θz). The geometric decoupling ensures large motion range along each translational direction and enables integration with large-stroke ground-mounted linear actuators or generators, depending on the application. The proposed design, which is based on a systematic arrangement of multiple rigid stages and parallelogram flexure modules, is analyzed via non-linear finite element analysis. A proof-of-concept prototype of the flexure mechanism is fabricated to validate its large range and decoupled motion capability. The analyses as well as the hardware demonstrate an XYZ motion range of 10 mm × 10 mm × 10 mm. Over this motion range, the non-linear FEA predicts a cross-axis error of less than 3%, parasitic rotations less than 2 mrad, less than 4% lost motion, actuator isolation less than 1.5%, and no perceptible motion direction stiffness variation. Ongoing work includes non-linear closed-form analysis and experimental measurement of these error motion and stiffness characteristics.

On the Reproducibility of Transducer Coupling for Acoustic Emission Testing

2006 ◽  
Vol 13-14 ◽  
pp. 117-124 ◽  
Author(s):  
James J. Hensman ◽  
C.V. Cristodaro ◽  
Gareth Pierce ◽  
Keith Worden
Keyword(s):  
Acoustic Emission ◽  
Test Results ◽  
Coupling Condition ◽  
Waveform Data ◽  
Three Point Bending ◽  
Emission Testing ◽  
Acoustic Emission Testing ◽  
Acoustic Emission Test ◽  
Point Bend ◽  
Ultrasonic Propagation

An acoustic emission test was simulated using a three point bend specimen and an artificial AE source. Waveform data was recorded as the sample was cyclically loaded in three point bending, and the cross correlation coefficient of the waveforms was used to measure the repeatability of the test. Results were twofold: the stress state of a specimen affects the ultrasonic propagation therein; and the coupling condition of a transducer may not remain constant during a test.

A Two-Dimensional Linear Assumed Strain Triangular Element for Finite Deformation Analysis

2005 ◽  
Vol 73 (6) ◽  
pp. 970-976 ◽  
Author(s):  
Fernando G. Flores
Keyword(s):  
Finite Deformation ◽  
Degrees Of Freedom ◽  
Yield Function ◽  
Triangular Element ◽  
Deformation Analysis ◽  
Elastic Model ◽  
Stress Strain ◽  
Metric Tensor ◽  
Assumed Strain ◽  
Non Linear

An assumed strain approach for a linear triangular element able to handle finite deformation problems is presented in this paper. The element is based on a total Lagrangian formulation and its geometry is defined by three nodes with only translational degrees of freedom. The strains are computed from the metric tensor, which is interpolated linearly from the values obtained at the mid-side points of the element. The evaluation of the gradient at each side of the triangle is made resorting to the geometry of the adjacent elements, leading to a four element patch. The approach is then nonconforming, nevertheless the element passes the patch test. To deal with plasticity at finite deformations a logarithmic stress-strain pair is used where an additive decomposition of elastic and plastic strains is adopted. A hyper-elastic model for the elastic linear stress-strain relation and an isotropic quadratic yield function (Mises) for the plastic part are considered. The element has been implemented in two finite element codes: an implicit static/dynamic program for moderately non-linear problems and an explicit dynamic code for problems with strong nonlinearities. Several examples are shown to assess the behavior of the present element in linear plane stress states and non-linear plane strain states as well as in axi-symmetric problems.

Sign in / Sign up

Export Citation Format

Share Document