Adsorption of Congo Red on AB-8 Macroporous Resin

2012 ◽  
Vol 550-553 ◽  
pp. 2138-2141
Author(s):  
Xin Dong Zhai ◽  
Jie Yan Wu
Keyword(s):  
Waste Water ◽  
Aqueous Solution ◽  
Congo Red ◽  
Freundlich Isotherm ◽  
Macroporous Resin ◽  
Order Model ◽  
Initial Concentration ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Agitation Time

Waste water containing Congo red in industrial production has caused many serious environmental problems worldwide. In this paper, AB-8 macroporous resin was used to remove Congo red from an aqueous solution by adsorption technique under varying conditions of pH, adsorbent dosage, agitation time, temperature and initial concentration. The results show the adsorption kinetics is well described by pseudo-second-order model. It was found that the equilibrium data was better represented by the Freundlich isotherm model.

scholarly journals Adsorption of As(V) from Aqueous Solution on Chitosan-Modified Diatomite

2020 ◽  
Vol 17 (2) ◽  
pp. 429 ◽  
Author(s):  
Qintao Yang ◽  
Liang Gong ◽  
Lili Huang ◽  
Qinglin Xie ◽  
Yijian Zhong ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Removal Efficiency ◽  
Ph Effect ◽  
Freundlich Isotherm ◽  
Xrd Analysis ◽  
Optimal Value ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Adsorption Desorption ◽  
Modified Diatomite

A novel chitosan (CS)-modified diatomite (Dt) was prepared by a simple mixture in the mass ratio to remove As(V) from aqueous solution in this research. The CS-modified Dt adsorbent was characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and X-ray powder diffraction (XRD) analysis. The parameters to influence the adsorption of As(V) ion were studied under such conditions as kinetics, adsorption isotherm, and pH effect. The results revealed that adsorption of As(V) was initially rapid and the equilibrium time was reached after 40 min. The optimal value of the pH was 5.0 for better adsorption. The equilibrium data were well fitted to the Langmuir isotherm compared to the Freundlich isotherm, and exhibited the highest capacity and removal efficiency of 94.3% under an initial As(V) concentration of 5 mg/L. The kinetic data were well described by the pseudo-second-order model. In addition, 0.1 M NaOH has the best desorption efficiency of As(V) adsorbed on CS-modified Dt, and the removal efficiency of As(V) was still higher than 90% when after six adsorption-desorption cycles. These results showed that the CS-modified Dt could be considered as a potential adsorbent for the removal of As(V) in aqueous solution.

Adsorption of Methylene Blue on Modified Bentonite

2013 ◽  
Vol 726-731 ◽  
pp. 2380-2383
Author(s):  
Li Xia Li ◽  
Xin Dong Zhai
Keyword(s):  
Methylene Blue ◽  
Aqueous Solutions ◽  
Adsorption Kinetics ◽  
Freundlich Isotherm ◽  
Batch Process ◽  
Experimental Results ◽  
Order Model ◽  
Modified Bentonite ◽  
Equilibrium Data ◽  
Pseudo Second Order

Modified bentonite was used as adsorbent for the methylene blue adsorption in a batch process. Experimental results show that the adsorption kinetics is well described by pseudo-second-order model and the equilibrium data was better represented by the Freundlich isotherm model. The results revealed that the modified bentonite has the potential to be used as a good adsorbent for the removal of methylene blue from aqueous solutions.

Removal of Pb (II) from Aqueous Solution by Blast-Furnace Slags

2013 ◽  
Vol 726-731 ◽  
pp. 2736-2741
Author(s):  
Ming Da Liu ◽  
Ge Tian ◽  
Liang Jie Zhao ◽  
Yao Sheng Wang ◽  
Lei Guo ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Blast Furnace ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Sorption Process ◽  
Second Order ◽  
Order Model ◽  
Pseudo Second Order ◽  
Solution Kinetic ◽  
Second Order Model

Five blast-furnace slags were used as adsorbents to remove Pb (II) from aqueous solution. Kinetic studies showed that the sorption process was best described by pseudo-second-order model. Among Langmuir, Freundlich and Temkin isotherms, the Freundlich isotherm had a better fit with the simulation of the adsorption of Pb (II).

scholarly journals Use of Ionic Liquid Pretreated and Fermented Sugarcane Bagasse as an Adsorbent for Congo Red Removal

Polymers ◽  
2021 ◽  
Vol 13 (22) ◽  
pp. 3943
Author(s):  
Uroosa Ejaz ◽  
Agha Arslan Wasim ◽  
Muhammad Nasiruddin Khan ◽  
Othman M. Alzahrani ◽  
Samy F. Mahmoud ◽  
...  
Keyword(s):  
Sugarcane Bagasse ◽  
Congo Red ◽  
Industrial Wastewater ◽  
Standard Free Energy ◽  
Freundlich Isotherm ◽  
Cellulase Production ◽  
Order Model ◽  
Toxic Dyes ◽  
Combined Pretreatment ◽  
Pseudo Second Order

A large amount of industrial wastewater containing pollutants including toxic dyes needs to be processed prior to its discharge into the environment. Biological materials such as sugarcane bagasse (SB) have been reported for their role as adsorbents to remove the dyes from water. In this study, the residue SB after fermentation was utilized for the dye removal. A combined pretreatment of NaOH and methyltrioctylammonium chloride was given to SB for lignin removal, and the pretreated SB was utilized for cellulase production from Bacillus aestuarii UE25. The strain produced 118 IU mL−1 of endoglucanse and 70 IU mL−1 of β-glucosidase. Scanning electron microscopy and FTIR spectra showed lignin and cellulose removal in fermented SB. This residue was utilized for the adsorption of an azo dye, congo red (CR). The thermodynamic, isotherm and kinetics studies for the adsorption of CR revealed distinct adsorption features of SB. Untreated SB followed Langmuir isotherm, whereas pretreated SB and fermented SB obeyed the Freundlich isotherm model. The pseudo-second-order model fitted well for the studied adsorbents. The results of thermodynamic studies revealed spontaneous adsorption with negative standard free energy values. Untreated SB showed a 90.36% removal tendency at 303.15 K temperature, whereas the adsorbents comprised of pretreated and fermented SB removed about 98.35% and 97.70%, respectively. The study provided a strategy to utilize SB for cellulase production and its use as an adsorbent for toxic dyes removal.

scholarly journals Adsorption of Se(IV) in aqueous solution by zeolites synthesized from fly ashes with different compositions

2019 ◽  
Vol 9 (4) ◽  
pp. 506-519
Author(s):  
Xiao Zhang ◽  
Xinyuan Li ◽  
Fan Zhang ◽  
Shaohao Peng ◽  
Sadam Hussain Tumrani ◽  
...  
Keyword(s):  
Fly Ash ◽  
Contact Time ◽  
High Capacity ◽  
Freundlich Isotherm ◽  
Fly Ashes ◽  
Order Model ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Equilibrium Data ◽  
Pseudo Second Order

Abstract Low-calcium fly ash (LC-F) and high-calcium fly ash (HC-F) were used to synthesize corresponding zeolites (LC-Z and HC-Z), then for adsorption of Se(IV) in water. The results showed that c zeolites can effectively adsorb Se(IV). The optimal adsorption conditions were set at contact time = 360 min; pH = 2.0; the amount of adsorbent = 5.0 g·L−1; temperature = 25 °C; initial Se(IV) concentration = 10 mg·L−1. The removal efficiency of HC-Z was higher than the LC-Z after it had fully reacted because the specific surface area (SSA) of HC-Z was higher than LC-Z. The adsorption kinetics model of Se(IV) uptake by HC-Z followed the pseudo-second-order model. The Freundlich isotherm model agreed better with the equilibrium data for HC-Z and LC-Z. The maximum Se(IV) adsorption capacity was 4.16 mg/g for the HC-Z and 3.93 mg/g for the LC-Z. For the coexisting anions, barely affected Se(IV) removal, while significant affected it. Regenerated zeolites still had high capacity for Se(IV) removal. In conclusion, zeolites synthesized from fly ashes are a promising material for adsorbing Se(IV) from wastewater, and selenium-loaded zeolite has the potential to be used as a Se fertilizer to release selenium in Se-deficient areas.

Congo Red Dye Removal Using Ca-Al Layered Double Hydroxide: Kinetics and Equilibrium

2019 ◽  
Vol 814 ◽  
pp. 463-468 ◽  
Author(s):  
Hong Tham Nguyen Thi ◽  
Duy Chinh Nguyen ◽  
Thi Thuong Nguyen ◽  
Van Thuan Tran ◽  
Huu Vinh Nguyen ◽  
...  
Keyword(s):  
Layered Double Hydroxide ◽  
Congo Red ◽  
Removal Rate ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Initial Concentration ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Red Dye ◽  
Double Hydroxide

This In this study, the Ca-Al layered double hydroxide was used as a potential adsorbent for the removal of Congo red from aqueous solutions. The effects of Initial concentration and contact time on the adsorption properties of Congo red by Ca-Al LDHs were studied. The removal rate of Conge red reached to 59.416 mg/g under room temperature with 0.2g of adsorbent, initial concentration of 50 ppm, adsorption time of 210 min, shaking speed of 90r/min. The experimental equilibrium data for the removal of Congo red were evaluated by various isotherm models. The pseudo-second-order kinetic models were found to fit the adsorption kinetics, and the equilibrium data were appropriately fitted to Langmuir and Freundlich model adsorption isotherm.

Thermodynamic and kinetic properties of the adsorption of 4-nitrophenol on graphene from aqueous solution

2015 ◽  
Vol 93 (10) ◽  
pp. 1083-1087 ◽  
Author(s):  
Ali Issa Ismail
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Kinetic Properties ◽  
Initial Concentration ◽  
First Order ◽  
Toxic Materials ◽  
Exothermic Process ◽  
Pseudo Second Order ◽  
Pseudo First Order

Graphene is a newly discovered material and is considered to be the new wonder material for many applications. The recent possibility of obtaining pure and fully characterized graphene opens the door to the study of the adsorption of toxic materials on graphene. The adsorption behavior of p-nitrophenol on graphene was studied in aqueous medium. The effect of each of pH, temperature, and dosage was emphasized. The highest calculated adsorption capacity of 4-nitrophenol was found to be 15.5 mg/g, assuming Langmuir fitting starting from 11.1 mg/g initial concentration at 298 K and pH = 6. Fitting the data using the Freundlich isotherm model predicted a favorable adsorption process (n > 1). The rise and saturation areas of the isotherms were fitted as pseudo first-order and pseudo second-order processes, respectively, with relatively good fit (k1 = 0.0023/s, k2 = 0.68 g mg−1 s−1). The thermodynamic properties indicated a spontaneous and exothermic process.

scholarly journals Equilibrium and Kinetic Study of Removal Copper(II) from Aqueous Solution Using Chicken Eggshells: Low Cost Sorbent

Molekul ◽  
2021 ◽  
Vol 16 (1) ◽  
pp. 28
Author(s):  
Mohammad Jihad Madiabu ◽  
Joko Untung ◽  
Imas Solihat ◽  
Andi Muhammad Ichzan
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Sorption Process ◽  
X Ray Diffraction ◽  
Order Model ◽  
X Ray ◽  
Adsorption Condition ◽  
Pseudo Second Order ◽  
Effect Of Copper

The research aims to investigate feasibility eggshells as potential adsorbent to remove copper(II) ions from aqueous solution. Eggshells powder was characterized using X-ray diffraction, scanning electron microscopy, and Fourier transform infrared spectroscopy. Effect of copper(II) initial concentration, adsorbent dosage, and contact time have conducted. The optimum adsorption condition obtained when 0.7 g eggshells applied to 50 mg/L copper(II) solution for 50 minutes. The maximum percentage of copper(II) removal was exceeded more than 85%. Langmuir and Freundlich isotherm model were applied to describe the equilibrium adsorption. Copper(II) kinetics sorption process was fitted to pseudo-second order model with a rate constant equal to 0.516 g/mg.min. The results clearly exhibit that eggshells powder can be effectively used to remove copper(II) ions from aqueous solutions.

scholarly journals The Application of Monkey Cola Pericarp (Cola lepidota) in the Removal of Toluene from Aqueous Medium

2020 ◽  
pp. 53-67
Author(s):  
C. Obi ◽  
N. C. Ngobiri ◽  
L. C. Agbaka ◽  
M. U. Ibezim-Ezeani
Keyword(s):  
Aqueous Medium ◽  
Contact Time ◽  
Second Order ◽  
Phytochemical Screening ◽  
Order Model ◽  
Initial Concentration ◽  
First Order ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Pseudo First Order

The study focused on the investigation of the effectiveness of the pericarp of monkey kola (Cola lepidota) biomass (CLPB) in the removal of toluene from aqueous system. X-Ray Diffraction (XRD), Fourier Transform Infrared (FTIR), Scanning Electron Microscopy (SEM) and phytochemical screening methods were used for characterizing the biosorbent. The effects of contact time, pH, and concentration on biosorption process were studied. The phytochemical screening showed the presence of alkaloids, flavonoids, tannins, carbohydrate, saponins and steroids. Carboxylic, alkene and alcohol groups were found to be the principal functional groups. The highest percentage removal was 99.63% at toluene initial concentration of 40 mg/L and 98.30% at pH 8. The contact time 30 minutes gave better removal efficiency of 99.89%. Among the biosorption isotherm models tested (Langmuir, Freundlich, Dubinin Radushkevich and Temkin, respectively), the Langmuir model equation gave a better fit of the equilibrium data with a correlation coefficient (R2) of 0.99. The equilibrium data was tested with pseudo-first order and pseudo-second order models and pseudo-second order model (R² = 0.99) fitted more than the pseudo-first order model (R² = 0.85). This study has revealed that Cola lepidota is a potential biosorbent for the removal of toluene from aqueous medium under the operating conditions of contact time of 30 minutes, pH of 8 and initial concentration of 40 mg/g.

Use of papaya seeds as a biosorbent of methylene blue from aqueous solution

2013 ◽  
Vol 68 (2) ◽  
pp. 441-447 ◽  
Author(s):  
Diego S. Paz ◽  
Alexandre Baiotto ◽  
Marcio Schwaab ◽  
Marcio A. Mazutti ◽  
Mariana M. Bassaco ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Second Order ◽  
Adsorption Kinetic ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Papaya Seeds ◽  
Second Order Model

In this study papaya seeds were used to remove methylene blue dye from aqueous solution. Papaya seeds were characterized as possessing a macro/mesoporous texture and large pore size. Studies were carried out in batches to evaluate the effect of contact time and pH (2–12) on the removal of dye. It was observed that the adsorption of dye was better in the basic region (pH 12). The equilibrium data were analyzed using Langmuir, Freundlich, Dubinin–Raduschkevich, Tempkin, Jovanovich, Redlich–Peterson, Sips, Toth and Radke–Prausnitz isotherms. The equilibrium data were best described by the Langmuir isotherm with a maximum adsorption capacity of 637.29 mg g–1. Adsorption kinetic data were fitted using the pseudo-first-order and pseudo-second-order model. The adsorption kinetic is very fast and was best described by the pseudo-second-order model.

Sign in / Sign up

Export Citation Format

Share Document