Novel Biobased Materials from Tung Oil-Based Monomer and Tung Oil-Modified Unsaturated Polyester

2012 ◽  
Vol 581-582 ◽  
pp. 121-124
Author(s):  
Cheng Guo Liu ◽  
Yong Hong Zhou ◽  
Li Hong Hu
Keyword(s):  
Thermal Stability ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Polymer Matrix ◽  
Unsaturated Polyester ◽  
Mechanical And Thermal Properties ◽  
Tung Oil ◽  
Biobased Materials

Two kinds of novel biobased materials were obtained by copolymerization of tung oil -based monomer (TOPERMA) or tung oil-modified unsaturated polyester (UPE-TO) with styrene. Mechanical and thermal properties of the two TO-based biopolymers were presented and compared. It was shown that the UPE-TO polymer matrix showed better toughness than the pure unsaturated polyester (UPE) matrix, while the TOPERMA polymer matrix had better thermal stability than the UPE-TO and the pure UPE matrixes by thermogravimetric analysis (TGA). These tung oil-based polymers show promise as an alternative to replace petroleum-based materials.

Dispersion, mechanical and thermal properties of nano graphite platelets reinforced flouroelastomer composites

e-Polymers ◽  
2008 ◽  
Vol 8 (1) ◽  
Author(s):  
Deng Xu ◽  
V. Sridhar ◽  
Thanh Tu Pham ◽  
Jin Kuk Kim
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Fracture Surface ◽  
Exfoliated Graphite ◽  
Mechanical And Thermal Properties ◽  
Reinforcing Fillers ◽  
Processing Of Composites

AbstractThe potential of exfoliated graphite nano platelets (xGnP™) as reinforcing fillers in flouroelastomer has been investigated. The dispersion of the nano graphite platelets in the polymer matrix has been investigated by WAXD, SEM, TEM, EPMA and AFM. WAXD studies indicated that the processing of composites did not change the inter-gallery distance (d-spacing) of the graphite platelets. The effect of increasing nano graphite loadings on mechanical properties like tensile strength, modulus and tear resistance has been studied. Formation of weld lines on the fracture surface of the composite has been observed by SEM. The thermal stability was determined using thermogravimetric analysis. The composites showed higher thermal stability in comparison with nonreinforced polymer.

scholarly journals Bio-based rigid polyurethane foam prepared from apricot stone shell-based polyol for thermal insulation application – Part 2: Morphological, mechanical, and thermal properties

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 6080-6094
Author(s):  
Muhammed Said Fidan ◽  
Murat Ertaş
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Polyurethane Foam ◽  
Flame Retardants ◽  
Compressive Modulus ◽  
Cell Diameter ◽  
Mechanical And Thermal Properties ◽  
Rigid Polyurethane Foam

The procedure for the liquefaction of apricot stone shells was reported in Part 1. Part 2 of this work determines the morphological, mechanical, and thermal properties of the bio-based rigid polyurethane foam composites (RPUFc). In this study, the thermal conductivity, compressive strength, compressive modulus, thermogravimetric analysis, flammability tests (horizontal burning and limited oxygen index (LOI)) in the flame retardants), and scanning electron microscope (SEM) (cell diameter in the SEM) tests of the RPUFc were performed and compared with control samples. The results showed the thermal conductivity (0.0342 to 0.0362 mW/mK), compressive strength (10.5 to 14.9 kPa), compressive modulus (179.9 to 180.3 kPa), decomposition and residue in the thermogravimetric analysis (230 to 491 °C, 15.31 to 21.61%), UL-94 and LOI in the flame retardants (539.5 to 591.1 mm/min, 17.8 to 18.5%), and cell diameter in the SEM (50.6 to 347.5 μm) of RPUFc attained from liquefied biomass. The results were similar to those of foams obtained from industrial RPUFs, and demonstrated that bio-based RPUFc obtained from liquefied apricot stone shells could be used as a reinforcement filler in the preparation of RPUFs, specifically in construction and insulation materials. Moreover, liquefied apricot stone shell products have potential to be fabricated into rigid polyurethane foam composites.

scholarly journals Examining the Influence of Re–Used Nanofiller—Pyrolyzed Montmorillonite, on the Thermal Properties of Polypropylene–Based Engineering Nanocomposites

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2636
Author(s):  
Tomasz M. Majka ◽  
Oskar Bartyzel ◽  
Konstantinos N. Raftopoulos ◽  
Joanna Pagacz ◽  
Krzysztof Pielichowski
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Control Sample ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Stabilization Effect ◽  
Polypropylene Melt ◽  
Better Than

Pyrolysis of the polypropylene/montmorillonite (PP/OMMT) nanocomposites allows for recovery of the filler that can be then re–used to produce PP/pyrolyzed MMT (PMMT) nanostructured composites. In this work, we discuss the thermal properties of PP/PMMT composites investigated by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). It has been found that effect of PMMT (5 wt. % and 10 wt. %) on matrix thermal stability occurs at temperatures above 300 °C. Addition of 5 wt. % and 10 wt. % of PMMT into polypropylene system gave good stabilization effect, as confirmed by the overall stabilization effect (OSE) values, which increased by 4% and 7%, respectively, compared to the control sample (PP). Interestingly, the presence of 1 wt. % and 3 wt. % of pyrolyzed clay stabilizes the system better than the same concentrations of organoclay added into polypropylene melt. DSC data revealed that pyrolyzed clay has still the same tendency as organoclay to enhance formation of the α and β crystalline PP phases only. The pyrolyzed MMT causes an improvement of the modulus in the glassy as well as rubbery regions, as confirmed by DMA results.

Morphology, Mechanical and Thermal Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites

2019 ◽  
Vol 972 ◽  
pp. 172-177
Author(s):  
Sirirat Wacharawichanant ◽  
Patteera Opasakornwong ◽  
Ratchadakorn Poohoi ◽  
Manop Phankokkruad
Keyword(s):  
Thermal Stability ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Tensile Stress ◽  
Cellulose Fibers ◽  
Phase Morphology ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Ethylene Copolymer ◽  
Thermal Stability Of

This work studied the effects of various types of cellulose fibers on the morphology, mechanical and thermal properties of poly(lactic acid) (PLA)/propylene-ethylene copolymer (PEC) (90/10 w/w) blends. The PLA/PEC blends before and after adding cellulose fibers were prepared by melt blending method in the internal mixer and molded by compression method. The morphological analysis observed that the presence of cellulose in PLA did not change the phase morphology of PLA, and PLA/cellulose composite surfaces were observed the cellulose fibers inserted in PLA matrix and fiber pull-out. The phase morphology of PLA/PEC blends was changed from brittle fracture to ductile fracture behavior and showed the phase separation between PLA and PEC phases. The presence of celluloses did not improve the compatibility between PLA and PEC phases. The tensile stress and strain curves found that the tensile stress of PLA was the highest value. The addition of all celluloses increased Young’s modulus of PLA. The PEC presence increased the tensile strain of PLA over two times when compared with neat PLA and PLA was toughened by PEC. The incorporation of cellulose fibers in PLA/PEC blends could improve Young’s modulus, tensile strength, and stress at break of the blends. The thermal stability showed that the degradation temperatures of all types of cellulose were less than the degradation temperatures of PLA. Thus, the incorporation of cellulose in PLA could not enhance the thermal stability of PLA composites and PLA/PEC composites. The degradation temperature of PEC was the highest value, but it could not improve the thermal stability of PLA. The incorporation of cellulose fibers had no effect on the melting temperature of the PLA blend and composites.

Mechanical and thermal properties of polyoxymethylene-matrix composites filled with multi-walled carbon nanotubes-coated milled glass fiber

2019 ◽  
Vol 54 (15) ◽  
pp. 1961-1976
Author(s):  
Xu Xiangmin ◽  
Hongxiang Zhang ◽  
Tong Beibei ◽  
Li Binjie ◽  
Yudong Zhang
Keyword(s):  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Thermal Properties ◽  
Electron Microscope ◽  
Glass Fiber ◽  
Crystallization Temperature ◽  
High Performance ◽  
Multiwall Carbon Nanotubes ◽  
Fiber Surface ◽  
Mechanical And Thermal Properties

The advanced multifunctional filler has become one of the main challenges in developing high-performance polymer composites. In this study, the acid-treated multiwall carbon nanotubes (MWCNTs) were adhered to the surface of milled glass fiber under the combined effect of 3-aminopropyltriethyloxy silane and tetraethyl orthosilicate to fabricate a hierarchical fiber (MWCNTs-MGF). The morphologies of the hierarchical fibers were characterized using field-emission scanning electron microscope and transmission electron microscope, which showed evidence of a coating layer of MWCNTs on each fiber surface. The MWCNTs-MGF was employed as a multifunctional filler to prepare polyoxymethylene-based composites using a twin-screw extruder by melt blending. The obtained composites exhibited improved mechanical and thermal properties. The composite tensile strength and notched impact strength and Young's modulus increased by 10%, 32%, and 32%, respectively, as the MWCNTs-MGF content varies from 0 to 10 wt.%. Meanwhile, the reinforcing and toughing mechanisms of MWCNTs-MGF were also elaborated by analyzing the interfacial adhesion and fracture morphologies of the composites. Moreover, the study on thermal stability and crystallization behavior indicated that the polyoxymethylene/MWCNTs-MGF composites had higher thermal stability, crystallization temperature, and crystallinity as compared to the polymer matrix. The improvement of thermal stability originates from the unique surface structure of MWCNTs-MGF, while the increase in crystallization temperature and crystallinity is due to the strong heterogeneous nucleation ability of the hierarchical fibers.

Effect of oil palm ash on the mechanical and thermal properties of unsaturated polyester composites

e-Polymers ◽  
2016 ◽  
Vol 16 (4) ◽  
pp. 323-329 ◽  
Author(s):  
J. Sahari ◽  
M.A. Maleque
Keyword(s):  
Thermal Properties ◽  
Oil Palm ◽  
Tensile Testing ◽  
Unsaturated Polyester ◽  
Morphological Characterization ◽  
Mechanical And Thermal Properties ◽  
Casting Method ◽  
Oil Palm Ash ◽  
Polyester Composites

AbstractThis research was carried out to evaluate the effect of oil palm ash (OPA) on the mechanical and thermal properties of biocomposites. Different compositions of OPA (i.e. 0, 10, 20 and 30 vol%) were introduced to unsaturated polyester (UPE) by using simple casting method with methyl ethyl ketone peroxide (MEKP) as a hardener. The specimens were prepared based on ASTM D5083 standards for tensile testing. From the results, it was found that the mechanical properties of UPE/OPA composites were improved in modulus with increasing the OPA content. The physical properties of UPE/OPA were also investigated where the density of biocomposites decrease with increasing OPA while the water absorption of UPE/OPA increase with increasing OPA. The thermal and morphological characterization of the UPE/OPA composites have been done using TGA, DSC and SEM.

Sign in / Sign up

Export Citation Format

Share Document