Effects of Retained Austenite Stability on Mechanical Properties of High Strength TRIP Steel

2012 ◽  
Vol 602-604 ◽  
pp. 287-293
Author(s):  
Zhi Feng Li ◽  
Ren Yu Fu ◽  
Qing Shan Li
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
High Strength ◽  
Tensile Tests ◽  
Transformation Kinetics ◽  
Austenite Stability ◽  
Kinetics Of ◽  
Strength And Ductility

Mechanical stability of retained austenite and its effect on mechanical properties of high strength TRIP steel were studied by means of OM, SEM, TEM, XRD, and mechanical testing after various heat treatments. Results revealed that the film-type retained austenite located between bainite laths with high carbon content showed gradual martensitic transformation with strain, demonstrating a good TRIP effect. Samples annealed at 800°C and held at 420°C showed an optimum value of strength and ductility product up to 18381.2MPa%. Transformation kinetics of the retained austenite were evaluated through tensile tests and fitted by the function y=0.86-0.86×exp(-Ax). The fitting results were good.

scholarly journals EFFECT OF C-Mn PARTITIONING ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TRIP STEEL

2021 ◽  
Vol 55 (2) ◽  
pp. 269-275
Author(s):  
Cainian Jing ◽  
Qiteng Lei ◽  
Tao Lin ◽  
Daomin Ye ◽  
Cong Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Lath Martensite ◽  
Tensile Tests ◽  
Microstructure And Mechanical Properties

In this paper, the TRIP590 steel was used for C-Mn partitioning. The influence of C-Mn partitioning on the microstructure and mechanical properties of the steel was studied. SEM, EPMA, XRD and tensile tests were used to characterize the microstructure of the tested steel, calculate the content of retained austenite, and analyze the enrichment of C atoms and Mn atoms and mechanical properties. The results show that there was a lot of lath martensite and scattered ferrite in the microstructures of the Q&P steel and C-Mn partitioning steel. After C-Mn partitioning, the content of ferrite was increased. The enrichment of C and Mn in the C-Mn partitioning steel was relatively apparent, and the concentration of the atoms in the center of martensite was significantly higher than at the boundary between martensite and ferrite. Mn-rich areas were also C-rich areas. Compared with the Q&P steel, the C-Mn partitioning steel had a larger amount of retained austenite, higher elongation and PSE.

scholarly journals Addressing Retained Austenite Stability in Advanced High Strength Steels

2013 ◽  
Vol 738-739 ◽  
pp. 212-216 ◽  
Author(s):  
Elena V. Pereloma ◽  
Azdiar A. Gazder ◽  
Ilana B. Timokhina
Keyword(s):  
Retained Austenite ◽  
Mechanical Stability ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Parameters ◽  
Advanced High Strength Steels ◽  
Austenite Stability ◽  
Retained Austenite Stability ◽  
Size And Morphology

Advances in the development of new high strength steels have resulted in microstructures containing significant volume fractions of retained austenite. The transformation of retained austenite to martensite upon straining contributes towards improving the ductility. However, in order to gain from the above beneficial effect, the volume fraction, size, morphology and distribution of the retained austenite need to be controlled. In this regard, it is well known that carbon concentration in the retained austenite is responsible for its chemical stability, whereas its size and morphology determines its mechanical stability. Thus, to achieve the required mechanical properties, control of the processing parameters affecting the microstructure development is essential.

scholarly journals Overcoming Strength-Ductility Trade-Off at Cryogenic Temperature of Low Carbon Low Alloy Steel via Controlling Retained Austenite Stability

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 157
Author(s):  
Xuelin Wang ◽  
Zhenjia Xie ◽  
Chengjia Shang ◽  
Gang Han
Keyword(s):  
Retained Austenite ◽  
Mechanical Stability ◽  
Testing Temperature ◽  
Low Carbon ◽  
Transformation Induced Plasticity ◽  
Strain Behavior ◽  
Austenite Stability ◽  
Work Hardening Rate ◽  
Multiphase Steel ◽  
Strength And Ductility

Stress–strain behavior of a low carbon low alloy multiphase steel with ferrite, tempered bainite, and retained austenite was studied at different cryogenic temperatures. Results indicated that both strength and ductility were enhanced with decreasing tensile testing temperature. The enhancement of both strength and ductility was attributed to the decreased mechanical stability of retained austenite with decreasing temperature, resulting in sufficient transformation induced plasticity (TRIP) effect for increasing work hardening rate.

Effect of Annealing Temperature on Austenite Stability of a δ-TRIP Steel

2019 ◽  
Vol 818 ◽  
pp. 82-86
Author(s):  
Xin Xu ◽  
Ren Dong Liu ◽  
Bao Yu Xu ◽  
Hong Liang Yi ◽  
Guo Dong Wang
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Austenite Stability ◽  
Poor Stability ◽  
Better Than

In this work, a novel type of δ-TRIP steel was designed, and the content and stability of retained austenite in δ-TRIP specimens under different annealing processes were detected and studied, respectively. The volume fraction of austenite was determined by X-ray diffraction (XRD). The microstructure and mechanical properties were analyzed systematically. The results show that a complex microstructure composed of three phases (ferrite, bainite and retained austenite) was obtained in the δ-TRIP steel. With the increasing of annealing temperature, both retained austenite and bainite content in the specimen increased, while the carbon content in retained austenite decreased, leading to a poor stability for retained austenite. Both tensile and yield strength improved with the increasing of annealing temperature, while the elongation reduced. The feature of retained austenite led to an excellent combination of ductility and strength, which was better than traditional TRIP steel.

scholarly journals Excellent mechanical properties of taenite in meteoric iron

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shohei Ueki ◽  
Yoji Mine ◽  
Kazuki Takashima
Keyword(s):  
Mechanical Properties ◽  
Nitrogen Solubility ◽  
High Strength ◽  
Tensile Tests ◽  
Metallographic Analysis ◽  
Advanced High Strength Steel ◽  
Analysis Techniques ◽  
Solid Solution Strengthening ◽  
Solution Strengthening ◽  
Strength And Ductility

AbstractMeteoric iron is the metal that humans first obtained and used in the earliest stage of metal culture. Advances in metallographic analysis techniques have revealed that meteoric iron largely comprises kamacite, taenite, and cohenite, which correspond to ferrite, austenite, and cementite in artificial steel, respectively. Although the mechanical properties of meteoric irons were measured previously to understand their origin and history, the genuine mechanical properties of meteoric iron remain unknown because of its complex microstructure and the pre-existing cracks in cohenite. Using micro-tensile tests to analyse the single-crystalline constituents of the Canyon Diablo meteorite, herein, we show that the taenite matrix exhibits excellent balance between yield strength and ductility superior to that of the kamacite matrix. We found that taenite is rich in nitrogen despite containing a large amount of nickel, which decreases the nitrogen solubility, suggesting that solid-solution strengthening via nitrogen is highly effective for the Fe–Ni system. Our findings not only provide insights for developing advanced high-strength steel but also help understand the mysterious relationship between nitrogen and nickel contents in steel. Like ancient peoples believed that meteoric iron was a gift from the heavens, the findings herein imply that this thought continues even now.

Effect of Al on the Microstructure and Mechanical Properties of Hot-Rolled Medium-Mn Steel

2018 ◽  
Vol 941 ◽  
pp. 292-298 ◽  
Author(s):  
Ding Ting Han ◽  
Yun Bo Xu ◽  
Ying Zou ◽  
Zhi Ping Hu ◽  
Shu Qing Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Trip Steel ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
Volume Fraction ◽  
Microstructure And Mechanical Properties ◽  
Medium Mn Steel ◽  
Hot Rolled ◽  
Mn Steel

The present investigation was made to study the effect of Al on the microstructure and mechanical properties of hot-rolled medium-Mn TRIP steel (abbreviated as Al-TRIP). As a contrast, a Si-added medium-Mn TRIP steel (abbreviated as Si-TRIP) was also studied. Addition Al in medium-Mn steel can raise Ac3 temperature, which will restrain austenite transformation and expand the two-phase region, promoting Mn and C elements enriched in austenite. In-depth microstructure and mechanical properties analysis were carried out for the hot-rolled Al-TRIP and Si-TRIP steels in this study. The microstructure was characterized by scanning electron microscope (SEM) and electron probe microanalyzer (EPMA). Volume fraction of retained austenite was measured by D/max2400 X-ray diffractometer (XRD). A dual-phase microstructure consisting of ultra-fine grained intercritical ferrite (IF) and lath-like retained austenite (RA) with high mechanical stability was obtained after annealing at 630°C for 2h for Al-TRIP steel. As prolonging the intercritical annealing time, the stability of RA decreased primarily due to the increase of grain size. The tensile test results indicated that the Al-TRIP steel possessed a better combination of tensile strength and elongation compared to Si-TRIP steel. Excellent mechanical properties with yield strength of 790MPa, tensile strength of 1050MPa, total elongation of 35% and UTS×TEL of 39GPa·% was obtained for the Al-TRIP steel.

scholarly journals Temperature Effects on Tensile Deformation Behavior of a Medium Manganese TRIP Steel and a Quenched and Partitioned Steel

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 375
Author(s):  
Whitney A. Poling ◽  
Emmanuel De Moor ◽  
John G. Speer ◽  
Kip O. Findley
Keyword(s):  
Trip Steel ◽  
Retained Austenite ◽  
Tensile Deformation ◽  
Flow Behavior ◽  
Uniform Elongation ◽  
High Strength Steels ◽  
Tensile Tests ◽  
Effect Of Temperature ◽  
Austenite Stability ◽  
Increasing Temperature

Third-generation advanced high-strength steels (AHSS) containing metastable retained austenite are being developed for the structural components of vehicles to reduce vehicle weight and improve crash performance. The goal of this work was to compare the effect of temperature on austenite stability and tensile mechanical properties of two steels, a quenched and partitioned (Q&P) steel with a martensite and retained austenite microstructure, and a medium manganese transformation-induced plasticity (TRIP) steel with a ferrite and retained austenite microstructure. Quasi-static tensile tests were performed at temperatures between −10 and 85 °C for the Q&P steel (0.28C-2.56Mn-1.56Si in wt.%), and between −10 and 115 °C for the medium manganese TRIP steel (0.14C-7.14Mn-0.23Si in wt.%). X-ray diffraction measurements as a function of strain were performed from interrupted tensile tests at all test temperatures. For the medium manganese TRIP steel, austenite stability increased significantly, serrated flow behavior changed, and tensile strength and elongation changed significantly with increasing temperature. For the Q&P steel, flow stress was mostly insensitive to temperature, uniform elongation decreased with increasing temperature, and austenite stability increased with increasing temperature. The Olson–Cohen model for the austenite-to-martensite transformation as a function of strain showed good agreement for the medium manganese TRIP steel data and fit most of the Q&P steel data above 1% strain.

Study on the Mechanical Stability of Retained Austenite in Cold-Rolled Medium-Mn Steel

2014 ◽  
Vol 936 ◽  
pp. 1283-1289
Author(s):  
Jun Hu ◽  
Wen Quan Cao ◽  
Jie Shi ◽  
Han Dong
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
Volume Fraction ◽  
Residual Austenite ◽  
Tensile Tests ◽  
Medium Mn Steel ◽  
Cold Rolled ◽  
Mn Steel ◽  
High Mechanical Stability

The mechanical stability of the retained austenite in the cold-rolled medium-Mn steel was studied. Tensile tests were carried out to measure the mechanical properties of the annealed steel. Scanning electron microscopy was applied to characterize the microstructure evolution during the tensile process; X-ray diffraction analysis was used to determine the residual austenite content in the deformed steel. It was found that the volume fraction of retained austenite gradually decreases with strain .The value of the stability coefficient of retained austenite k was small in the test steel, which indicated high mechanical stability of retained austenite. Due to TRIP effect, the high mechanical stability of the retained austenite strongly delays the onset of necking, which resulted in good comprehensive mechanical properties with ultrahigh strength and plasticity.

scholarly journals Mechanical Properties of a Bainitic Steel Producible by Hot Rolling

2017 ◽  
Vol 62 (4) ◽  
pp. 2331-2338 ◽  
Author(s):  
R. Rana ◽  
S. Chen ◽  
A. Haldar ◽  
S. Das
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Hot Rolling ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
High Strength ◽  
Salt Bath ◽  
Lower Amount ◽  
Subzero Temperature ◽  
C 30

AbstractA carbide-free bainitic microstructure is suitable for achieving a combination of ultra high strength and high ductility. In this work, a steel containing nominally 0.34C-2Mn-1.5Si-1Cr (wt.%) was produced via industrial hot rolling and laboratory heat treatments. The austenitization (900°C, 30 min.) and austempering (300-400°C, 3 h) treatments were done in salt bath furnaces. The austempering treatments were designed to approximately simulate the coiling step, following hot rolling and run-out-table cooling, when the bainitic transformation would take place and certain amount of austenite would be stabilized due to suppression of carbide precipitation. The microstructures and various mechanical properties (tensile properties, bendability, flangeability, and room and subzero temperature impact toughness) relevant for applications were characterized. It was found that the mechanical properties were highly dependent on the stability of the retained austenite, presence of martensite in the microstructure and the size of the microstructural constituents. The highest amount of retained austenite (~ 27 wt.%) was obtained in the sample austempered at 375°C but due to lower austenite stability and coarser overall microstructure, the sample exhibited lower tensile ductility, bendability, flangeability and impact toughness. The sample austempered at 400°C also showed poor properties due to the presence of initial martensite and coarse microstructure. The best combination of mechanical properties was achieved for the samples austempered at 325-350°C with a lower amount of retained austenite but with the highest mechanical stability.

scholarly journals Quasi-Situ Characterization of Retained Austenite Orientation in Quenching and Partitioning Steel via Uniaxial Tensile Tests

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4609
Author(s):  
Pengfei Gao ◽  
Jie Liu ◽  
Weijian Chen ◽  
Feng Li ◽  
Jingyu Pang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
Volume Fraction ◽  
Electron Backscatter Diffraction ◽  
Early Stage ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Quenching And Partitioning ◽  
Austenite Grains

As a representative of the third generation of advanced high strength steel, the quenching and partitioning steel has excellent potential in automobile manufacturing. The characterization and analysis of the mechanical properties and microstructure of the quenching and partitioning steel during deformation is an effective way to explore the microstructure evolution and transformation-induced plasticity effects of complex phase steels. The relationship between the microstructure morphology and mechanical properties of a 1180 MPa-grade quenching and partitioning steel was investigated through interrupted uniaxial tensile tests plus quasi-situ electron backscatter diffraction measurements. A mixture of ferrite, martensite, and retained austenite was observed in the microstructure. It was found that the volume fraction of global retained austenite decreased linearly with the increase of displacement (0 mm–1.05 mm). The evolution of the retained austenite with typical crystal direction ranges with deformation was characterized. Results show that the orientation (111) and (311) account for the highest proportion of retained austenite grains in the undeformed sample and the mechanical stability of the (311) retained austenite grains is the best. Moreover, the retained austenite grains rotated significantly in the early stage of the specimen deformation process (around yielding), and the work hardening of the specimen was weak at this stage, simultaneously.

Sign in / Sign up

Export Citation Format

Share Document