scholarly journals Mechanical Properties of a Bainitic Steel Producible by Hot Rolling

2017 ◽  
Vol 62 (4) ◽  
pp. 2331-2338 ◽  
Author(s):  
R. Rana ◽  
S. Chen ◽  
A. Haldar ◽  
S. Das
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Hot Rolling ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
High Strength ◽  
Salt Bath ◽  
Lower Amount ◽  
Subzero Temperature ◽  
C 30

AbstractA carbide-free bainitic microstructure is suitable for achieving a combination of ultra high strength and high ductility. In this work, a steel containing nominally 0.34C-2Mn-1.5Si-1Cr (wt.%) was produced via industrial hot rolling and laboratory heat treatments. The austenitization (900°C, 30 min.) and austempering (300-400°C, 3 h) treatments were done in salt bath furnaces. The austempering treatments were designed to approximately simulate the coiling step, following hot rolling and run-out-table cooling, when the bainitic transformation would take place and certain amount of austenite would be stabilized due to suppression of carbide precipitation. The microstructures and various mechanical properties (tensile properties, bendability, flangeability, and room and subzero temperature impact toughness) relevant for applications were characterized. It was found that the mechanical properties were highly dependent on the stability of the retained austenite, presence of martensite in the microstructure and the size of the microstructural constituents. The highest amount of retained austenite (~ 27 wt.%) was obtained in the sample austempered at 375°C but due to lower austenite stability and coarser overall microstructure, the sample exhibited lower tensile ductility, bendability, flangeability and impact toughness. The sample austempered at 400°C also showed poor properties due to the presence of initial martensite and coarse microstructure. The best combination of mechanical properties was achieved for the samples austempered at 325-350°C with a lower amount of retained austenite but with the highest mechanical stability.

Effects of Retained Austenite Stability on Mechanical Properties of High Strength TRIP Steel

2012 ◽  
Vol 602-604 ◽  
pp. 287-293
Author(s):  
Zhi Feng Li ◽  
Ren Yu Fu ◽  
Qing Shan Li
Keyword(s):  
Mechanical Properties ◽  
Trip Steel ◽  
Retained Austenite ◽  
Mechanical Stability ◽  
High Strength ◽  
Tensile Tests ◽  
Transformation Kinetics ◽  
Austenite Stability ◽  
Kinetics Of ◽  
Strength And Ductility

Mechanical stability of retained austenite and its effect on mechanical properties of high strength TRIP steel were studied by means of OM, SEM, TEM, XRD, and mechanical testing after various heat treatments. Results revealed that the film-type retained austenite located between bainite laths with high carbon content showed gradual martensitic transformation with strain, demonstrating a good TRIP effect. Samples annealed at 800°C and held at 420°C showed an optimum value of strength and ductility product up to 18381.2MPa%. Transformation kinetics of the retained austenite were evaluated through tensile tests and fitted by the function y=0.86-0.86×exp(-Ax). The fitting results were good.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

2010 ◽  
Vol 654-656 ◽  
pp. 82-85 ◽  
Author(s):  
Shu Zhou ◽  
Ying Wang ◽  
Nai Lu Chen ◽  
Yong Hua Rong ◽  
Jian Feng Gu
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Significant Fraction ◽  
Rolled Plate ◽  
Quenching And Partitioning ◽  
Good Ductility ◽  
Hot Rolled ◽  
Rolled Plates

The quenching-partitioning-tempering (Q-P-T) process, based on the quenching and partitioning (Q&P) treatment, has been proposed for producing high strength steels containing significant fraction of film-like retained austenite and controlled amount of fine martensite laths. In this study, a set of Q-P-T processes for C-Mn-Si-Ni-Nb hot rolled plates are designed and realized. The steels with Q-P-T processes present a combination of high strength and relatively good ductility. The origin of such mechanical properties is revealed by microstructure characterization.

Microstructure and Tensile Properties of TRIP-Aided Steel Sheet Subjected to Hot-Rolling and Austempering

2021 ◽  
Vol 1016 ◽  
pp. 732-737
Author(s):  
Junya Kobayashi ◽  
Hiroto Sawayama ◽  
Naoya Kakefuda ◽  
Goroh Itoh ◽  
Shigeru Kuraoto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Hot Rolling ◽  
Manufacturing Process ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Isothermal Holding ◽  
High Strength ◽  
Isothermal Transformation ◽  
Transformation Process ◽  
Steel Sheets

Various high strength steel sheets for weight reduction and safety improvement of vehicles have been developed. TRIP-aided steel with transformation induced plasticity of the retained austenite has high strength and ductility. Conventional TRIP-aided steels are subjected to austempering process after austenitizing. Generally, elongation and formability of TRIP-aided steel are improved by finely dispersed retained austenite in BCC phase matrix. The finely dispersed retained austenite and grain refinement of TRIP-aided steel can be achieved by hot rolling with heat treatment. Therefore, the improvement of mechanical properties of TRIP-aided steel is expected from the manufacturing process with hot rolling and then isothermal transformation process. In this study, thermomechanical heat treatment is performed by combining hot rolling and isothermal holding as the manufacturing process of TRIP-aided steel sheets. The complex phase matrix is obtained by hot rolling and then isothermal holding. Although the hardness of the hot rolled and isothermal held TRIP-aided steel is decreased, the volume fraction of retained austenite is increased.

scholarly journals Effect of enhanced weld cooling on the mechanical properties of a structural steel with a yield strength of 700 MPa

2020 ◽  
Vol 2 (11) ◽  
Author(s):  
Juhani Laitila ◽  
Lassi Keränen ◽  
Jari Larkiola
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Fatigue Strength ◽  
Impact Toughness ◽  
Yield Strength ◽  
Uniform Elongation ◽  
High Strength ◽  
Low Alloy Steel ◽  
External Cooling ◽  
Welding Processes

AbstractIn this study, we present the effect of enhanced cooling on the mechanical properties of a high-strength low-alloy steel (having a yield strength of 700 MPa) following a single-pass weld process. The properties evaluated in this study include uniform elongation, impact toughness, yield, tensile and fatigue strengths alongside the cooling time of the weld. With the steel used in this study, the enhanced cooling resulted in a weld joint characterized with excellent cross-weld uniform elongation, yield and fatigue strength. The intensified cooling reduced the time it takes for the weld to reach 100 °C by around 190 s. Not only the fusion line of the weld was less pronounced, but also the grain size of the CGHAZ was greatly refined as a result of the enhanced cooling. The results indicate that combining external cooling to the welding processes can be beneficial for the studied high-strength steel.

scholarly journals Effect of Retained Austenite and Non-Metallic Inclusions on the Mechanical Properties of Resistance Spot Welding Nuggets of Low-Alloy TRIP Steels

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1064 ◽  
Author(s):  
Víctor H. Vargas Cortés ◽  
Gerardo Altamirano Guerrero ◽  
Ignacio Mejía Granados ◽  
Víctor H. Baltazar Hernández ◽  
Cuauhtémoc Maldonado Zepeda
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Retained Austenite ◽  
High Strength ◽  
Microstructural Characterization ◽  
Spot Welds ◽  
Trip Steels ◽  
Resistance Spot ◽  
Lap Shear ◽  
Metallic Inclusions

The combination of high strength and formability of transformation induced plasticity (TRIP) steels is interesting for the automotive industry. However, the poor weldability limits its industrial application. This paper shows the results of six low-alloy TRIP steels with different chemical composition which were studied in order to correlate retained austenite (RA) and non-metallic inclusions (NMI) with their resistance spot welded zones to their joints’ final mechanical properties. RA volume fractions were quantified by X-ray microdiffraction (µSXRD) while the magnetic saturation technique was used to quantify NMI contents. Microstructural characterization and NMI of the base metals and spot welds were assessed using scanning electron microscopy (SEM). Weld nuggets macrostructures were identified using optical microscopy (OM). The lap-shear tensile test was used to determine the final mechanical properties of the welded joints. It was found that NMI content in the fusion zone (FZ) was higher than those in the base metal and heat affected zone (HAZ). Whereas, traces of RA were found in the HAZ of highly alloyed TRIP steels. Lap-shear tensile test results showed that mechanical properties of spot welds were affected by NMI contents, but in a major way by the decomposition of RA in the FZ and HAZ.

Effect of Retained Austenite Stability on Mechanical Properties of Bainitic Rail Steel

2014 ◽  
Vol 1004-1005 ◽  
pp. 198-202 ◽  
Author(s):  
Kai Kai Wang ◽  
Zhun Li Tan ◽  
Gu Hui Gao ◽  
Xiao Lu Gui ◽  
Bing Zhe Bai
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Rail Steel ◽  
High Impact ◽  
Good Thermal Stability ◽  
Austenite Stability ◽  
Retained Austenite Stability ◽  
Close Relationship ◽  
The Stability

Retained austenite has an important effect on strength and toughness of 20Mn2SiCrMo bainitic rail steel. In this work, the stability of retained austenite and mechanical properties have been studied. The results show that impact toughness of experimental steel has close relationship with the stability of retained austenite. When tempered at lower than 350°C, retained austenite owns good thermal stability, corresponding to relatively high impact toughness.

scholarly journals The Effect of Tempering on the Microstructure and Mechanical Properties of a Novel 0.4C Press-Hardening Steel

2019 ◽  
Vol 9 (20) ◽  
pp. 4231
Author(s):  
Oskari Haiko ◽  
Antti Kaijalainen ◽  
Sakari Pallaspuro ◽  
Jaakko Hannula ◽  
David Porter ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Temperature ◽  
Impact Toughness ◽  
Retained Austenite ◽  
Hot Strip Mill ◽  
Tempering Temperature ◽  
Press Hardening ◽  
Dislocation Densities ◽  
The Impact

In this paper, the effects of different tempering temperatures on a recently developed ultrahigh-strength steel with 0.4 wt.% carbon content were studied. The steel is designed to be used in press-hardening for different wear applications, which require high surface hardness (650 HV/58 HRC). Hot-rolled steel sheet from a hot strip mill was austenitized, water quenched and subjected to 2-h tempering at different temperatures ranging from 150 °C to 400 °C. Mechanical properties, microstructure, dislocation densities, and fracture surfaces of the steels were characterized. Tensile strength greater than 2200 MPa and hardness above 650 HV/58 HRC were measured for the as-quenched variant. Tempering decreased the tensile strength and hardness, but yield strength increased with low-temperature tempering (150 °C and 200 °C). Charpy-V impact toughness improved with low-temperature tempering, but tempered martensite embrittlement at 300 °C and 400 °C decreased the impact toughness at −40 °C. Dislocation densities as estimated using X-ray diffraction showed a linear decrease with increasing tempering temperature. Retained austenite was present in the water quenched and low-temperature tempered samples, but no retained austenite was found in samples subjected to tempering at 300 °C or higher. The substantial changes in the microstructure of the steels caused by the tempering are discussed.

Sign in / Sign up

Export Citation Format

Share Document