Experimental Investigation of Utilizing Industrial Waste and Byproduct Materials in Controlled Low Strength Materials (CLSM)

2013 ◽  
Vol 639-640 ◽  
pp. 299-303 ◽  
Author(s):  
Hao Wu ◽  
Jian Yin ◽  
Shu Bai
Keyword(s):  
Fly Ash ◽  
Laboratory Experiments ◽  
Bottom Ash ◽  
High Water ◽  
Paper Sludge ◽  
Fine Aggregate ◽  
Fibrous Materials ◽  
Test Results ◽  
Natural Sand ◽  
Strength Tests

Laboratory experiments were conducted in this study to investigate the suitability and applicability of incorporating fly ash, bottom ash and paper sludge with various contents into CLSM mixtures. Fly ash was used as a substitute for Portland cement, bottom ash was added by partially replacing fine aggregate, while paper sludge was treated as a fibrous admixture. Physical and mechanically properties of the CLSM mixtures were examined through flowability, compressive strength, and splitting tensile strength tests. The test results indicated that both fly ash and bottom ash can be potentially used as basic materials for CLSM mixtures with desirable performances, and by limiting the amount of cement used in the mixture, the ultimate strength of CLSM could be easily controlled available for excavation. The strength of the CLSM mixtures were reduced to some extent by incorporating high content of fly ash, while they were significantly increased with high content of natural sand replaced by bottom ash. Due to the high water absorption of the paper sludge, the mixture with paper sludge added exhibited relatively low flowability, and it showed no benefits on enhancing compressive and splitting tensile strengths as common fibrous materials.

Strength Enhancement of Bottom Ash-Based Concretes Using Metakaolin

2011 ◽  
Vol 695 ◽  
pp. 287-290
Author(s):  
J. M. Zhao ◽  
Z. X. Yang ◽  
Kyu Hong Hwang ◽  
M. C. Kim
Keyword(s):  
Compressive Strength ◽  
Fresh Concrete ◽  
Setting Time ◽  
Bottom Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Replacement Ratio ◽  
Natural Sand ◽  
Strength Enhancement ◽  
Compressive Strength Of Concrete

To replace bottom ash for natural sand completely, the mix proportions of bottom ash in concrete was adjusted according to tab density and replacement ratio of Metakaolin/Cement were established. And then testing for slump, setting time, and compressive strength was conducted. According to test results, the compressive strength of concrete using the bottom ash was lower than that of concrete using natural sand (BAO concrete). But by adjusting the amount of bottom ash in concrete according tab density so that the fine aggregate proportions change 44% to 38%, the compressive strength of concrete using the bottom ash could even be higher than BAO concrete. And the chloric content of concrete using the bottom ash increased as the replacement ratio of bottom ash increased, but it is satisfied with the chloric content of fresh concrete 0.30 kg/m2 below (concrete standard specification regulation value).

scholarly journals Effect of Fly Ash on Mortar Mixes with Quarry Dust as Fine Aggregate

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Baboo Rai ◽  
Sanjay Kumar ◽  
Kumar Satish
Keyword(s):  
Experimental Investigation ◽  
Compressive Strength ◽  
Fly Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Excellent Performance ◽  
Natural Sand ◽  
Transverse Strength ◽  
Combined Use ◽  
Quarry Dust

This paper presents the results of an experimental investigation carried out to evaluate the compressive strength and transverse strength of 1 : 3 mortar mixes in which natural sand was replaced with 20%, 50%, and 100% quarry dust by weight which were further modified by partially replacing cement with four percentages (15%, 20%, 25%, and 30%) of low calcium fly ash. The compressive strength was determined at 3, 7, 28, and 50 days of age while transverse strength was determined at 28 and 50 days age. Test results revealed that the combined use of quarry rock dust and fly ash exhibited excellent performance due to efficient microfilling ability and pozzolanic activity.

Strength Enhancement of Bottom Ash-Based Polymer Concretes

2011 ◽  
Vol 488-489 ◽  
pp. 278-281
Author(s):  
J. M. Zhao ◽  
Z. X. Yang ◽  
Kyu Hong Hwang ◽  
J.K. Lee ◽  
M. C. Kim ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Bottom Ash ◽  
Resin Cement ◽  
Fine Aggregate ◽  
Test Results ◽  
Natural Sand ◽  
Polymeric Resin ◽  
Compressive Strength Of Concrete ◽  
Increased Strength

To replace bottom ash for natural sand completely, the mix proportions of bottom ash in concrete was adjusted according to tab density and replacement ratio of polymeric resin/Potland cement(PC) were established. And then testing for slump, setting time, and compressive strength was conducted. According to test results, the compressive strength of concrete using the bottom ash was lower than that of concrete using natural sand (BA0 concrete). But by adjusting the amount of bottom ash in concrete according tab density so that the fine aggregate proportions change 44% to 38%, the compressive strength of concrete using the bottom ash could even be higher than BA0 concrete. And as the polymeric resin content of bottom ash concrete increased, strength would be increased drastically, but proper dispersant should be cooperated with polymeric resin cement with fine bottom ash powders.

scholarly journals Reactivity of Ground Coal Bottom Ash to Be Used in Portland Cement

J ◽  
2021 ◽  
Vol 4 (3) ◽  
pp. 223-232
Author(s):  
Esperanza Menéndez ◽  
Cristina Argiz ◽  
Miguel Ángel Sanjuán
Keyword(s):  
Fly Ash ◽  
Coal Fly Ash ◽  
Bottom Ash ◽  
Blended Cement ◽  
Coal Ash ◽  
Pozzolanic Reaction ◽  
Natural Sand ◽  
Coal Bottom Ash ◽  
Novel Material ◽  
Pozzolanic Properties

Ground coal bottom ash is considered a novel material when used in common cement production as a blended cement. This new application must be evaluated by means of the study of its pozzolanic properties. Coal bottom ash, in some countries, is being used as a replacement for natural sand, but in some others, it is disposed of in a landfill, leading thus to environmental problems. The pozzolanic properties of ground coal bottom ash and coal fly ash cements were investigated in order to assess their pozzolanic performance. Proportions of coal fly ash and ground coal bottom ash in the mixes were 100:0, 90:10, 80:20, 50:50, 0:100. Next, multicomponent cements were formulated using 10%, 25% or 35% of ashes. In general, the pozzolanic performance of the ground coal bottom ash is quite similar to that of the coal fly ash. As expected, the pozzolanic reaction of both of them proceeds slowly at early ages, but the reaction rate increases over time. Ground coal bottom ash is a promising novel material with pozzolanic properties which are comparable to that of coal fly ashes. Then, coal bottom ash subjected to an adequate mechanical grinding is suitable to be used to produce common coal-ash cements.

scholarly journals The Use of Sheet Glass Powder as Fine Aggregate Replacement in Concrete

2010 ◽  
Vol 4 (1) ◽  
pp. 65-71 ◽  
Author(s):  
M. Mageswari ◽  
Dr. B. Vidivelli
Keyword(s):  
Sheet Glass ◽  
Glass Powder ◽  
Fine Aggregate ◽  
Test Results ◽  
Natural Sand ◽  
Aggregate Concrete ◽  
Fine Aggregates ◽  
Interesting Possibility ◽  
Compact State ◽  
Conservation Of Natural Resources

Sheet glass powder (SGP) used in concrete making leads to greener environment. In shops, near by Chidambaram many sheet glass cuttings go to waste, which are not recycled at present and usually delivered to landfills for disposal. Using SGP in concrete is an interesting possibility for economy on waste disposal sites and conservation of natural resources. This paper examines the possibility of using SGP as a replacement in fine aggregate for a new concrete. Natural sand was partially replaced (10%, 20%, 30%, 40% and 50%) with SGP. Compressive strength, Tensile strength (cubes and cylinders) and Flexural strength up to 180 days of age were compared with those of concrete made with natural fine aggregates. Fineness modulus, specific gravity, moisture content, water absorption, bulk density, %voids, % porosity (loose and compact) state for sand (S) and SDA were also studied. The test results indicate that it is possible to manufacture concrete containing Sheet glass powder (SGP) with characteristics similar to those of natural sand aggregate concrete provided that the percentage of SGP as fine aggregate is limited to 10-20%, respectively.

scholarly journals Strength Tests and Numerical Simulations of Loess Modified by Desulfurization Ash and Fly Ash

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 512
Author(s):  
Zhi Cheng ◽  
Xinrong Cheng ◽  
Yuchao Xie ◽  
Zhe Ma ◽  
Yuhao Liu
Keyword(s):  
Shear Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Utilization Rate ◽  
Direct Shear ◽  
Test Results ◽  
Mass Ratio ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Actual Test

Desulfurization ash and fly ash are solid wastes discharged from boilers of power plants. Their utilization rate is low, especially desulfurization ash, most of which is stored. In order to realize their resource utilization, they are used to modify loess in this paper. Nine group compaction tests and 32 group direct shear tests are done in order to explore the influence law of desulfurization ash and fly ash on the strength of the loess. Meanwhile, FLAC3D software is used to numerically simulate the direct shear test, and the simulation results and the test results are compared and analyzed. The results show that, with the increase of desulfurization ash’s amount, the shear strength of the modified loess increases first and then decreases. The loess modified by the fly ash has the same law with that of the desulfurization ash. The best mass ratio of modified loess is 80:20. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 12.74% higher than that of the pure loess on average and the shear strength of loess modified by fly ash is 3.59% higher than that of the pure loess on average. The effect of the desulfurization ash on modifying the loess is better than that of the fly ash. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 9.15% higher than that of the fly ash on average. Comparing the results of the simulation calculation with the actual test results, the increase rate of the shear stress of the FLAC3D simulation is larger than that of the actual test, and the simulated shear strength is about 8.21% higher than the test shear strength.

Study on the Influence of Mix Design Parameters on the Properties of Self-Compacting Concrete

2013 ◽  
Vol 857 ◽  
pp. 10-19
Author(s):  
Ji Liang Wang ◽  
Xiang Qian Wen ◽  
Jun Hong Shan ◽  
Ying Liu
Keyword(s):  
Fly Ash ◽  
Volume Content ◽  
Coarse Aggregate ◽  
Mineral Admixture ◽  
Design Parameters ◽  
Fine Aggregate ◽  
Test Results ◽  
Self Compacting Concrete ◽  
Volume Stability ◽  
Dry Shrinkage

the influence of mixing amount of mineral admixture, volume content of fine and coarse aggregate have been systematical studied on the workability, mechanical properties and volume stability of self-compacting concrete. Test results showed that with the fly ash content increased, the workability of self-compacting concrete improved significantly, early compressive strength decreased, but increase rate of later strength improved remarkably, and the mixing amount of fly ash inhibited significantly the dry shrinkage of self-compacting concrete; with the volume content of coarse aggregate increased, the workability of self-compacting concrete decreased significantly, but the volume stability of self-compacting concrete improved obviously, thus the optimum volume content of coarse aggregate of self-compacting concrete was range from 0.30 to 0.34; when the volume content of fine aggregate varied at the range of 0.40~0.50, there may be little effects on the workability of self-compacting concrete, but the increase self-compacting concretes volume content could reduce obviously the dry shrinkage of self-compacting concrete. Moreover, the variation in the volume content of coarse and fine aggregate should have slight influence on the early strength of self-compacting concrete, and the influence of the volume content variety on the later strength of self-compacting concrete could be neglected eventually.

Properties of Unfired Building Bricks Prepared from Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 754-755 ◽  
pp. 468-472 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Hardened Properties

This work investigates the possibility of using fly ash (FA) and Vietnam residual rice husk ash (RHA) in producing unfired building bricks with applying densified mixture design algorithm (DMDA) method. In this research, little amount of cement was added into the mixtures as binder substitution. Unground rice husk ash (URHA), an agricultural by-product, was used as partial fine aggregate replacement (10% and 30%) in the mixtures. The solid bricks of 220×105×60 mm in size were prepared in this study. The hardened properties of the bricks were investigated including compressive strength, flexural strength and water absorption according to corresponding Vietnamese standards. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens obtained good mechanical properties, which were well conformed to Vietnamese standard. Compressive strength and flexural strength of the bricks were respectively in range of 13.81–22.06 MPa and 2.25–3.47 MPa. It was definitely proved many potential applications of FA and RHA in the production of unfired building bricks.

Assessment of Pb-slag, MSWI bottom ash and boiler and fly ash for using as a fine aggregate in cement mortar

2008 ◽  
Vol 154 (1-3) ◽  
pp. 766-777 ◽  
Author(s):  
Nabajyoti Saikia ◽  
Geert Cornelis ◽  
Gilles Mertens ◽  
Jan Elsen ◽  
Koenraad Van Balen ◽  
...  
Keyword(s):  
Fly Ash ◽  
Cement Mortar ◽  
Bottom Ash ◽  
Fine Aggregate ◽  
Mswi Bottom Ash

scholarly journals Mechanical and Durability Properties of Concrete Made with Used Foundry Sand as Fine Aggregate

2015 ◽  
Vol 2015 ◽  
pp. 1-11 ◽  
Author(s):  
G. Ganesh Prabhu ◽  
Jin Wook Bang ◽  
Byung Jae Lee ◽  
Jung Hwan Hyun ◽  
Yun Yong Kim
Keyword(s):  
Substitution Rate ◽  
International Standards ◽  
Fine Aggregate ◽  
Test Results ◽  
Natural Sand ◽  
Foundry Sand ◽  
Durability Properties ◽  
Concrete Mixtures ◽  
Concrete Production ◽  
Strength And Durability

In recent years, the construction industry has been faced with a decline in the availability of natural sand due to the growth of the industry. On the other hand, the metal casting industries are being forced to find ways to safely dispose of waste foundry sand (FS). With the aim of resolving both of these issues, an investigation was carried out on the reuse of waste FS as an alternative material to natural sand in concrete production, satisfied with relevant international standards. The physical and chemical properties of the FS were addressed. The influence of FS on the behaviour of concrete was evaluated through strength and durability properties. The test results revealed that compared to the concrete mixtures with a substitution rate of 30%, the control mixture had a strength value that was only 6.3% higher, and this enhancement is not particularly high. In a similar manner, the durability properties of the concrete mixtures containing FS up to 30% were relatively close to those of control mixture. From the test results, it is suggested that FS with a substitution rate of up to 30% can be effectively used in concrete production without affecting the strength and durability properties of the concrete.

Sign in / Sign up

Export Citation Format

Share Document