FEM Based Numerical Simulation of Delta Parallel Mechanism

2013 ◽  
Vol 690-693 ◽  
pp. 2978-2981 ◽  
Author(s):  
Jian Zhong Zhang ◽  
Xin Peng Xie ◽  
Chuan Jin Li ◽  
Ying Ying Xin ◽  
Zhao Ming He
Keyword(s):  
Inverse Kinematics ◽  
Degrees Of Freedom ◽  
Inverse Dynamics ◽  
Theoretical Foundation ◽  
Future Research ◽  
Element Analysis ◽  
Pick And Place ◽  
Integral Structure ◽  
Inverse Dynamics Analysis ◽  
Three Degrees Of Freedom

This paper describes a parallel three degrees of freedom delta mechanism used for pick-and-place. It has the advantages of simple integral structure, strong bearing capacityhigh precisionkinematics and dynamics performance. According to this mechanism wide development prospect, the company study on the inverse kinematics inverse dynamics analysis and the static analysis by using ANSYS finite element analysis Software of Delta. These analyses have laid a good theoretical foundation for future research. These researches provide possible for widely used in foodpackingautomated assembly line occasions of small and medium-sized enterprises.

Effects of Dynamic Model Errors in Task-Priority Operational Space Control

Robotica ◽  
2021 ◽  
pp. 1-12
Author(s):  
Paolo Di Lillo ◽  
Gianluca Antonelli ◽  
Ciro Natale
Keyword(s):  
Inverse Kinematics ◽  
Degrees Of Freedom ◽  
Inverse Dynamics ◽  
Null Space ◽  
Control Algorithms ◽  
Model Errors ◽  
Operational Space ◽  
Dynamic Level ◽  
Concurrent Tasks ◽  
Modeling Errors

SUMMARY Control algorithms of many Degrees-of-Freedom (DOFs) systems based on Inverse Kinematics (IK) or Inverse Dynamics (ID) approaches are two well-known topics of research in robotics. The large number of DOFs allows the design of many concurrent tasks arranged in priorities, that can be solved either at kinematic or dynamic level. This paper investigates the effects of modeling errors in operational space control algorithms with respect to uncertainties affecting knowledge of the dynamic parameters. The effects on the null-space projections and the sources of steady-state errors are investigated. Numerical simulations with on-purpose injected errors are used to validate the thoughts.

A Model of the Human Spine: Forward and Inverse Kinematics

1992 ◽  
Author(s):  
Sunil Kumar Agrawal ◽  
Siyan Li ◽  
Glen Desmier
Keyword(s):  
Range Of Motion ◽  
Inverse Kinematics ◽  
Degrees Of Freedom ◽  
Kinematic Model ◽  
Joint Angles ◽  
Human Spine ◽  
Forward And Inverse Kinematics ◽  
Position And Orientation ◽  
Three Degrees Of Freedom ◽  
Adjacent Vertebra

Abstract The human spine is a sophisticated mechanism consisting of 24 vertebrae which are arranged in a series-chain between the pelvis and the skull. By careful articulation of these vertebrae, a human being achieves fine motion of the skull. The spine can be modeled as a series-chain with 24 rigid links, the vertebrae, where each vertebra has three degrees-of-freedom relative to an adjacent vertebra. From the studies in the literature, the vertebral geometry and the range of motion between adjacent vertebrae are well-known. The objectives of this paper are to present a kinematic model of the spine using the available data in the literature and an algorithm to compute the inter vertebral joint angles given the position and orientation of the skull. This algorithm is based on the observation that the backbone can be described analytically by a space curve which is used to find the joint solutions..

Finite Element Analysis of 2-D Structures by New Strain Based Triangular Element

2018 ◽  
Vol 35 (3) ◽  
pp. 305-313 ◽  
Author(s):  
C. Rebiai
Keyword(s):  
Dynamic Analysis ◽  
Degrees Of Freedom ◽  
Numerical Solutions ◽  
Time Integration ◽  
Triangular Element ◽  
Membrane Element ◽  
Lumped Mass ◽  
Element Analysis ◽  
Benchmark Tests ◽  
Three Degrees Of Freedom

ABSTRACTIn this investigation, a new simple triangular strain based membrane element with drilling rotation for 2-D structures analysis is proposed. This new numerical model can be used for linear and dynamic analysis. The triangular element is named SBTE and it has three nodes with three degrees of freedom at each node. The displacements field of this element is based on the assumed functions for the various strains satisfying the compatibility equations. This developed element passed both patch and benchmark tests in the case of bending and shear problems. For the dynamic analysis, lumped mass with implicit/explicit time integration are employed. The obtained numerical results using the developed element converge toward the analytical and numerical solutions in both analyses.

scholarly journals Load–Displacement Characterization in Three Degrees-of-Freedom for General Lamina Emergent Torsion Arrays

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
Nathan A. Pehrson ◽  
Pietro Bilancia ◽  
Spencer Magleby ◽  
Larry Howell
Keyword(s):  
Degrees Of Freedom ◽  
Design Space ◽  
Element Analysis ◽  
Array Design ◽  
Elastic Load ◽  
In Series ◽  
Load Displacement ◽  
Stiffness Characteristics ◽  
Tunable Stiffness ◽  
Three Degrees Of Freedom

Abstract Lamina emergent torsion (LET) joints for use in origami-based applications enables folding of panels. Placing LET joints in series and parallel (formulating LET arrays) opens the design space to provide for tunable stiffness characteristics in other directions while maintaining the ability to fold. Analytical equations characterizing the elastic load–displacement for general serial–parallel formulations of LET arrays for three degrees-of-freedom are presented: rotation about the desired axis, in-plane rotation, and extension/compression. These equations enable the design of LET arrays for a variety of applications, including origami-based mechanisms. These general equations are verified using finite element analysis, and to show variability of the LET array design space, several verification plots over a range of parameters are provided.

scholarly journals Design and analysis of a 3-DOF planar micromanipulation stage with large rotational displacement for micromanipulation system

2017 ◽  
Vol 8 (1) ◽  
pp. 117-126 ◽  
Author(s):  
Bingxiao Ding ◽  
Yangmin Li ◽  
Xiao Xiao ◽  
Yirui Tang ◽  
Bin Li
Keyword(s):  
Nanoimprint Lithography ◽  
Inverse Kinematics ◽  
Degrees Of Freedom ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
Rotational Displacement ◽  
Revolute Joints ◽  
Kinematic Models ◽  
Lever Mechanism ◽  
Three Degrees Of Freedom

Abstract. Flexure-based mechanisms have been widely used for scanning tunneling microscopy, nanoimprint lithography, fast servo tool system and micro/nano manipulation. In this paper, a novel planar micromanipulation stage with large rotational displacement is proposed. The designed monolithic manipulator has three degrees of freedom (DOF), i.e. two translations along the X and Y axes and one rotation around Z axis. In order to get a large workspace, the lever mechanism is adopted to magnify the stroke of the piezoelectric actuators and also the leaf beam flexure is utilized due to its large rotational scope. Different from conventional pre-tightening mechanism, a modified pre-tightening mechanism, which is less harmful to the stacked actuators, is proposed in this paper. Taking the circular flexure hinges and leaf beam flexures hinges as revolute joints, the forward kinematics and inverse kinematics models of this stage are derived. The workspace of the micromanipulator is finally obtained, which is based on the derived kinematic models.

Dynamic Trajectory Planning for a Three Degrees-of-Freedom Cable-Driven Parallel Robot Using Quintic B-Splines

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Sen Qian ◽  
Kunlong Bao ◽  
Bin Zi ◽  
W. D. Zhu
Keyword(s):  
Trajectory Planning ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Planning Method ◽  
End Effector ◽  
B Spline ◽  
B Splines ◽  
Pick And Place ◽  
Two Factors ◽  
Three Degrees Of Freedom

Abstract This paper presents a new trajectory planning method based on the improved quintic B-splines curves for a three degrees-of-freedom (3-DOF) cable-driven parallel robot (CDPR). First, the conditions of positive cables’ tension are expressed in terms of the position and acceleration constraints of the end-effector. Then, an improved B-spline curve is introduced, which is employed for generating a pick-and-place path by interpolating a set of given via-points. Meanwhile, by expressing the position and acceleration of the end-effector in terms of the first and second derivatives of the improved B-spline, the cable tension constraints are described in the form of B-spline parameters. According to the properties of the defined pick-and-place path, the proposed motion profile is dominated by two factors: the time taken for the end-effector to pass through all the via-points and the ratio between the nodes of B-spline. The two factors are determined through multi-objective optimization based on the efficiency coefficient method. Finally, experimental results on a 3-DOF CDPR show that the improved B-spline exhibits overall superior behavior in terms of velocity, acceleration, and cables force compared with the traditional B-spline. The validity of the proposed trajectory planning method is proved through the experiments.

scholarly journals Design and Implementation of a Multi-Function Gripper for Grasping General Objects

2019 ◽  
Vol 9 (24) ◽  
pp. 5266 ◽  
Author(s):  
Long Kang ◽  
Jong-Tae Seo ◽  
Sang-Hwa Kim ◽  
Wan-Ju Kim ◽  
Byung-Ju Yi
Keyword(s):  
Degrees Of Freedom ◽  
Manual Labor ◽  
Cluttered Environments ◽  
Industrial Robotics ◽  
Design And Implementation ◽  
Suction Cup ◽  
Working Environments ◽  
Wide Range ◽  
Pick And Place ◽  
Three Degrees Of Freedom

The development of a reliable pick-and-place system for industrial robotics is facing an urgent demand because many manual-labor works, such as piece-picking in warehouses and fulfillment centers tend toward automation. This paper presents an integrated gripper that combines a linkage-driven underactuated gripper with a suction gripping system for picking up a variety of objects in different working environments. The underactuated gripper consists of two fingers, and each finger has three degrees of freedom that are obtained by stacking one five-bar mechanism over one double parallelogram. Furthermore, each finger is actuated by two motors, both of which can be installed at the base owing to the special architecture of the proposed robotic finger. A suction cup is used to grasp objects in narrow spaces and cluttered environments. The combination of the suction and traditional linkage-driven grippers allows stable and reliable grasping under different working environments. Finally, practical experiments using a wide range of objects and under different grasping scenarios are performed to demonstrate the grasping capability of the integrated gripper.

Kinematic Analysis of a New 3-DOF Translational Parallel Manipulator

2005 ◽  
Author(s):  
Yangmin Li ◽  
Qingsong Xu
Keyword(s):  
Inverse Kinematics ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Screw Theory ◽  
Industrial Applications ◽  
Forward Kinematics ◽  
Physical Constraints ◽  
Mechanical Joints ◽  
Reachable Workspace ◽  
Three Degrees Of Freedom

A novel three-degrees-of-freedom (3-DOF) translational parallel manipulator (TPM) with orthogonally arranged fixed actuators is proposed in this paper. The mobility of the manipulator is analyzed via screw theory. The inverse kinematics, forward kinematics, and velocity analyses are performed and the singularities and isotropic configurations are investigated in details afterwards. Under different cases of physical constraints imposed by mechanical joints, the reachable workspace of the manipulator is geometrically generated and compared. Especially, it is illustrated that the manipulator in principle possesses a fairly regular like workspace with a maximum cuboid defined as the usable workspace inscribed and one isotropic configuration involved. Furthermore, the singularity within the usable workspace is verified, and simulation results show that there exist no any singular configurations within the specified workspace. Therefore, the presented new manipulator has a great potential for high precision industrial applications such as assembly, machining, etc.

scholarly journals Validation of the Inverse Dynamic Analysis of Human Gait Using a Forward Dynamics Approach

2013 ◽  
Author(s):  
Rosa Pàmies-Vilà ◽  
Josep M. Font-Llagunes
Keyword(s):  
Dynamic Analysis ◽  
Degrees Of Freedom ◽  
Inverse Dynamics ◽  
Human Gait ◽  
Intermediate Step ◽  
Inverse Dynamic ◽  
Joint Forces ◽  
Simulated Motion ◽  
Dynamical Consistency ◽  
Inverse Dynamics Analysis

One of the aims of the dynamic analysis of human gait is to know the joint forces and torques that the musculoskeletal system produces during the motion. For this purpose, an 18 segment 3D model with 57 degrees of freedom is implemented. The analysis of a captured motion can be addressed by means of forward or inverse dynamic analyses. In this work, both analyses are computed using multibody dynamics techniques. The forward dynamic analysis is carried out with the aim of simulating the movement of the multibody system using the results of the inverse problem as input data. Since the inverse analysis is solved using a dynamically consistent methodology, the forward dynamic analysis allows us to simulate up to the 90% of the gait cycle without any controller. After that, a proportional derivative (PD) controller is implemented to stabilize the system, which gets to simulate the complete captured motion. Moreover, the dynamic contribution of the controller is really low and the simulated motion is extremely close to the original one. The methodology presented allows us to validate the correctness of the inverse dynamics analysis and it is an intermediate step towards the prediction problem: it requires dynamical consistency too, but the uncertainties involved in the problem are lower than in a predictive approach.

Sign in / Sign up

Export Citation Format

Share Document