Analysis of the Mechanical Properties of Rice Husk Reinforced Polyethylene Composites Using Experiments with Mixtures

2013 ◽  
Vol 747 ◽  
pp. 395-398 ◽  
Author(s):  
Ahmad Bilal ◽  
Richard Lin ◽  
Krishnan Jayaraman
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Rice Husk ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Charpy Impact ◽  
Thermoplastic Composites ◽  
Design Expert ◽  
Wood Fibres ◽  
Charpy Impact Strength

In recent years, the use of agro-wastes, such as rice husk (RH), in the manufacture of thermoplastic composites to replace wood fibres has emerged as a promising field of interest. Linear medium density polyethylene (LMDPE) and ground rice husk (GRH) were used to manufacture composites. The D-optimal design routine in Design Expert software was used to select ten different blends with different percentages of RH, MDPE and compatibiliser, maleated polyethylene (MAPE) along with four replicate blends. RH was varied between 15 to 50 wt%, MAPE between 1 to 6 wt% and MDPE between 44 to 84 wt%. The effects of RH, MDPE and MAPE content on the mechanical properties of the manufactured composites were examined. The results show that tensile and flexural properties of the composites were improved, whereas, Charpy impact strength was decreased with increasing RH loading. The effect of MAPE on tensile strength and Charpy impact strength was significant, but its effect was negligible on tensile modulus, flexural strength and flexural modulus of the composites.

scholarly journals Improving Mechanical Properties of PLA/Starch Blends Using Masterbatch Containing Vegetable Oil Based Active Ingredients

Polymers ◽  
2021 ◽  
Vol 13 (17) ◽  
pp. 2981
Author(s):  
Bianka Nagy ◽  
Norbert Miskolczi ◽  
Zoltán Eller
Keyword(s):  
Impact Strength ◽  
Vegetable Oil ◽  
Rapeseed Oil ◽  
Flexural Modulus ◽  
Charpy Impact ◽  
Sem Images ◽  
Elongation At Break ◽  
Starch Concentration ◽  
Starch Blends ◽  
Charpy Impact Strength

The aim of this research was to increase the compatibility between PLA and starch with vegetable oil-based additives. Based on tensile results, it can be stated, that Charpy impact strength could be improved for 70/30 and 60/40 blends in both unconditioned and conditioned cases, regardless of vegetable oil, while no advantageous change in impact strength was obtained with PLA-g-MA. Considering sample with the highest starch concentration (50%), the flexural modulus was improved by using sunflower oil-based additive, Charpy impact strength and elongation at break was increased using rapeseed oil-based additive in both conditioned and unconditioned cases. SEM images confirmed the improvement of compatibility between components.

Effects of the Size of Wood Flour on Mechanical Properties of Wood-Plastic Composites

2011 ◽  
Vol 393-395 ◽  
pp. 76-79 ◽  
Author(s):  
Hai Bing Huang ◽  
Hu Hu Du ◽  
Wei Hong Wang ◽  
Hai Gang Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Wood Flour ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Inorganic Filler ◽  
Full Potential ◽  
Wood Plastic Composites ◽  
Plastic Composites

In this article, wood-plastic composites(WPCs) were manufactured with wood flour(80～120mesh、40～80mesh、20～40mesh、10～20mesh) combing with high density polyethylene(HDPE). Effects of the size of wood flour on mechanical properies and density of composites were investigated. Results showed that particle size of wood flour had an important effect on properitiesof WPCs. Change of mesh number had a outstanding effect on flexural modulus, tensile modulus and impact strength, howere, little effect on flexural strength and tensile strength. When mesh number of wood flour changed from 80～120mesh to 10～20mesh,flexural modulus and tensile modulus were respectively enhanced by 42.4% and 28.4%, respectively, and impact strength was decreased by 35.5%.Size of wood flour basically had no effect on density of composite within 10～120mesh. The use of wood flour or fiber as fillers and reinforcements in thermoplastics has been gaining acceptance in commodity plastics applications in the past few years. WPCs are currently experiencing a dramatic increase in use. Most of them are used to produce window/door profiles,decking,railing,ang siding. Wood thermoplastic composites are manufactured by dispering wood fiber or wood flour(WF) into molten plastics to form composite materials by processing techniques such as extrusion,themoforming, and compression or injection molding[1]. WPCs have such advantages[2]：(1)With wood as filler can improve heat resistance and strength of plastic, and wood has a low cost, comparing with inorganic filler, wood has a low density. Wood as strengthen material has a great potential in improving tensile strength and flexural modulus[3]；(2) For composite of same volume, composites with wood as filler have a little abrasion for equipment and can be regenerated；(3)They have a low water absorption and low hygroscopic property, They are not in need of protective waterproof paint, at the same time, composite can be dyed and painted for them own needs；(4)They are superior to wood in resistantnce to crack、leaf mold and termite aspects, composites are the same biodegradation as wood；(5)They can be processed or connected like wood；（6）They can be processed into a lots of complicated shape product by means of extrusion or molding and so on, meanwhile, they have high-efficiency raw material conversion and itself recycle utilization[4]. While there are many sucesses to report in WPCs, there are still some issues that need to be addressed before this technology will reach its full potential. This technology involves two different types of materials: one hygroscopic(biomass) and one hydrophobic(plastic), so there are issues of phase separation and compatibilization[5]. In this paper, Effects of the size of wood powder on mechanical properties of WPCs were studied.

Effect of various additives on mechanical properties of rice husk polypropylene (RHPP) composites

2012 ◽  
Vol 32 (3) ◽  
Author(s):  
Vinay Kumar ◽  
Manohar Singh Saini ◽  
Bikram Kishore Kanungo ◽  
Shishir Sinha
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Rice Husk ◽  
Zirconium Oxide ◽  
Thermoplastic Composites ◽  
Polypropylene Composite ◽  
Polypropylene Composites

Abstract Abundantly available rice husk can be used with polypropylene for the development of thermoplastic composites. The present study deals with mechanical properties such as hardness and impact strength of rice husk polypropylene composites with the addition of talc, mica, CaCO3, wollastonite, and zirconium oxide. Maleic anhydride polypropylene was used as compatibilizer. Improvement in the hardness and impact strength of the composites was observed by the use of these additives. Possible applications of rice husk polypropylene composite are in building and automobile sectors.

Mechanical properties of jute fiber reinforced polypropylene composite: Effect of chemical treatment by benzenediazonium salt in alkaline medium

BioResources ◽  
2010 ◽  
Vol 5 (3) ◽  
pp. 1618-1625
Author(s):  
M. Alamgir Kabir ◽  
M. Monimul Huque ◽  
M. Rabiul Islam ◽  
Andrzej K. Bledzki
Keyword(s):  
Mechanical Properties ◽  
Alkaline Medium ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Charpy Impact ◽  
Alkaline Media ◽  
Jute Fiber ◽  
Composite Effect ◽  
Elongation At Break ◽  
Pp Composites

Raw jute fiber was treated with o-hydroxybenzenediazonium salt (o-HBDS) in alkaline media. Raw and modified jute fiber were used to prepare composites by mixing with polypropylene (PP) plastic in different weight fractions (20, 25, 30, and 35%) of jute fiber. The mechanical properties except elongation at break of o-HBDS-treated (in alkaline medium) jute fiber-PP composite were higher than those of PP alone, raw jute fiber-PP composites, and alkali-treated jute fiber-PP composites. The elongation at break of treated jute-PP composite decreased to a large extent as compared to that of PP. The increase of tensile strength, tensile modulus, flexural strength, flexural modulus, and Charpy impact strength were found to be exceptionally high (in some cases ~200%) as compared to those of literature values.

Compatibility Effect of Reactive Copolymers on the Morphology, Rheology, and Mechanical Properties of Recycled Poly(ethylene terephthalate)/Polypropylene Blends

2014 ◽  
Vol 893 ◽  
pp. 254-258 ◽  
Author(s):  
Xin Tu Lin ◽  
Qing Rong Qian ◽  
Li Ren Xiao ◽  
Qiao Ling Huang ◽  
Li Zeng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Glycidyl Methacrylate ◽  
Ethylene Terephthalate ◽  
Charpy Impact ◽  
Poly Ethylene Terephthalate ◽  
Poly Ethylene ◽  
Polypropylene Blends ◽  
Pp Blends ◽  
Charpy Impact Strength

Glycidyl methacrylate (GMA) grafted ethyleneoctene multi-block copolymer (OBC) in the presence of the styrene (St) monomer (OBC-g-(GMA-co-St)) was prepared and then used as a compatibilizer for recycled Poly (ethylene terephthalate)/Polypropylene (R-PET/PP) blends. The morphological, rheological and mechanical properties of the blends were investigated. The results show that the compatibilization between R-PET and PP blends is improved by the introduction of OBC-g-(GMA-co-St). The SEM results show that all R-PET/PP blends exhibit a matrix-dispersed droplet type morphology, and the addition of OBC-g-(GMA-co-St) results in a finer morphology and better adhension between the phases. In addition, the storage moduli (G'), loss moduli (G") and the Charpy impact strength of the blends increase with increasing OBC-g-(GMA-co-St) content, while the the flexural strength decreases slightly.

Effect of inorganic pigments on the properties of coextruded polypropylene-based composites

2016 ◽  
Vol 31 (1) ◽  
pp. 23-33 ◽  
Author(s):  
Svetlana Butylina ◽  
Ossi Martikka ◽  
Timo Kärki
Keyword(s):  
Tensile Strength ◽  
Iron Oxide ◽  
Impact Strength ◽  
Water Immersion ◽  
Tensile Modulus ◽  
Charpy Impact ◽  
Immersion Test ◽  
Accelerated Weathering ◽  
Inorganic Pigments ◽  
Charpy Impact Strength

In this article, the effect of the incorporation of three inorganic pigments on the properties of coextruded polypropylene-based composites was studied. Three different pigments were incorporated in the shell layer of the composites: iron oxide, titanium dioxide (TiO2) and zinc oxide (ZnO). The tensile properties and Charpy impact strength of the composites were tested. A water immersion test was conducted. The morphology of the fractured surfaces of composites was characterised by scanning electron microscopy. The durability of the composites was assessed by testing colour characteristics and tensile strength after 500 hours of accelerated weathering. The results revealed that the TiO2-containing composite had the highest tensile modulus and Charpy impact strength, while the ZnO-containing composite had the lowest tensile strength and Charpy impact strength. Iron oxide was found to have no effect on either the physical or mechanical properties of the composite. The porosity of composites influences their water absorption and thickness swelling. The TiO2-containing composite exhibited better colour stability.

scholarly journals Mechanical Properties of Abaca Fiber Reinforced Urea Formaldehyde Composites

2015 ◽  
Vol 12 (1) ◽  
pp. 54-59 ◽  
Author(s):  
Abhishek Suvarna ◽  
Akash Katagi ◽  
Jackson Pasanna ◽  
Sunil Kumar ◽  
Basavaraju Bennehalli ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Urea Formaldehyde ◽  
Charpy Impact ◽  
Fiber Reinforced ◽  
Compression Moulding ◽  
Charpy Impact Strength

The present investigation focuses on the fabrication and mechanical characterization of alkali treated natural abaca fiber reinforced urea formaldehyde composites. The composites were prepared by means of compression moulding, and then the effects of fiber loading on mechanical properties such as tensile strength, flexural strength and impact strength were investigated. The composite with 40 wt% abaca fibers gave excellent tensile strength and flexural strength showing that it has the most superior bonding and adhesion of all the composites. In particular, the highest value, 10.02 kJ/m2 of charpy impact strength is observed in the composite with 50 wt% abaca fiber. This work revealed the potential of using abaca fibers in fiberboard.

Mechanical properties of unidirectional aligned bagasse fibers/vinyl ester composite

2016 ◽  
Vol 36 (2) ◽  
pp. 157-163 ◽  
Author(s):  
Ayyanar Athijayamani ◽  
Balasubramaniam Stalin ◽  
Susaiyappan Sidhardhan ◽  
Azeez Batcha Alavudeen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Vinyl Ester ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Short Beam ◽  
Beam Shear ◽  
The Matrix ◽  
The Impact

Abstract The present study describes the preparation of aligned unidirectional bagasse fiber-reinforced vinyl ester (BFRVE) composites and their mechanical properties such as tensile, flexural, shear and impact strength. Composites were prepared by a hand lay-up technique developed in our laboratory with the help of a hot press. Mechanical properties were obtained for different fiber contents by varying the number of layers. The obtained tensile property values were compared with the theoretical results. The results show that the tensile strength increased linearly up to 44 wt% and then dropped. However, the tensile modulus increased linearly from 17 wt% to 60 wt%. In the case of flexural properties, the flexural strength increased up to 53 wt% and started to decrease. However, the flexural modulus also increased linearly up to 60 wt%. The impact strength values were higher than the matrix materials for all the specimens. The short beam shear strength values were also increased up to 53 wt% and then dropped. The modified Bowyer and Bader (MBB) model followed by the Hirsch model shows a very good agreement with experimental results in both tensile strength and modulus.

Experimental studies on mechanical properties and toughening mechanisms of PA6/zeolite nanocomposites

2021 ◽  
pp. 095440622110057
Author(s):  
Rasool Mohsenzadeh
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Experimental Studies ◽  
Tensile Modulus ◽  
Twin Screw ◽  
Sem Micrograph ◽  
Crack Pinning ◽  
The Many

In recent years, polymer/inorganic nanocomposite have attracted the attention of researchers because of the many superior properties. Incorporation of nano-zeolite as a spherical nano-particle, into the PA6 matrix, can improve the stiffness-toughness properties simultaneously. PA6/zeolite nanocomposites standard mechanical testing specimens, containing different fractions (2.5, 5 and 7.5 wt.%) of nanosized zeolite particles were produced by utilizing a twin screw extruder and injection molding. The mechanical properties were characterized and the morphology was studied using scanning electron microscopy (SEM). The SEM micrograph showed that nano-zeolite were uniformly distributed in the PA6 matrix. The incorporation of nano-zeolite into PA6, increased the tensile strength, tensile modulus, flexural strength, flexural modulus and impact strength. Moreover, nano-zeolite stiffen and toughen PA6 simultaneously, and optimal properties were achieved at 5 wt.% of PA6/zeolite in flexural strength and impact strength. A number of strengthening mechanisms including crack pinning and crack deflection were detected for nanocomposite gear samples.

Impact of Natural and Synthetic Nanofibres Presence in Polymeric Composites on Mechanical Properties

2014 ◽  
Vol 1613 ◽  
pp. 133-139 ◽  
Author(s):  
Martin Seidl ◽  
Jiří Bobek ◽  
Jiří Habr ◽  
Petr Lenfeld ◽  
Luboš Běhálek
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Coupling Agent ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Polymeric Composites ◽  
Polymeric Nanocomposites ◽  
Cellulose Fibres ◽  
Three Phase ◽  
Natural And Synthetic

ABSTRACTThis study deals with evaluation of mechanical properties (tensile, flexural and impact strength), that verified reinforcing potential of nanofibres in polymeric composites and their applicability in dependence on the filler content of nanofibres of natural and synthetic origin. Considering the hydrophilic nature of natural nanofibres and hydrophobic polypropylene matrix was applied chemical modification that ensures effective interlock of nanofibres with the matrix, namely maleic anhydride grafted polypropylene and ionic modifier. Polymeric nanocomposites were prepared by twin screw extrusion that made possible mixing of all three components together. After cooling in water bath the composites were cut on pellets and dried for further injection moulding. The specimens were made of two- or three-phase component systems that included PP matrix, coupling agent in the volume of 4 wt.% and reinforcing nanofillers in the volume of 2, 4 and 6 wt.%. The presence of nanoparticles and coupling agents had not unambiguous impact on analysed mechanical properties. Coupling agent presence was dominant for impact strength, however, flexural and tensile properties were influenced mainly by the nanofiller type and origin. The dispersed phase and compatibilizer improved flexural modulus but tensile modulus of pure PP were not achieved by three-phase composite, not even with the highest analysed nanoparticle load. Cellulose fibres proved as more proper than the synthetic ones not only for their biodegradability and renewability but for their better toughness as well.

Sign in / Sign up

Export Citation Format

Share Document