Numerical Investigations of Spray Droplet Parameters in a Direct Injection Diesel Engine Using 3-Z Extended Coherent Flame Model

2013 ◽  
Vol 768 ◽  
pp. 226-230 ◽  
Author(s):  
Manimaran Renganathan ◽  
R. Thundil Karuppa Raj
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Time Step ◽  
Spray Droplet ◽  
Fluid Mixture ◽  
Combustion Modeling ◽  
Spray Formation ◽  
Direct Injection Diesel Engine

Diesel engine combustion modeling presents a challenging task as the injection starts with the spray formation and breakup of spray into droplets. The computation involved in predicting the in-cylinder fluid mixture during combustion using eulerian and lagrangian approach is rather a cumbersome task. In this work, 3D-CFD computations are performed to understand the behaviour of spray droplet variables on combustion process and emissions in a direct injection diesel engine. The study involves the computation of turbulent flow-field quantities, modelling various processes such as fuel spray distribution, atomization, collision, evaporation, combustion and pollutant formation using a commercial CFD code. Grid independence and time independent studies are carried out for finding the optimum grid size and time step. The numerical results predicted using CFD code is validated with the experimental data available from the literature. The process of combustion and emission characteristics is investigated numerically with respect to spray characteristics. The work is further extended to study the effect of swirl ratio and injection timing on droplet parameters.

CFD Modelling of the Effects of Injection Timing on the Combustion Process and Emissions in an HSDI Diesel Engine

2012 ◽  
Author(s):  
Raouf Mobasheri ◽  
Zhijun Peng
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Cfd Simulation ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Cfd Modelling ◽  
Combustion Modeling ◽  
Pressure Trace ◽  
Hsdi Diesel Engine

High-Speed Direct Injection (HSDI) diesel engines are increasingly used in automotive applications due to superior fuel economy. An advanced CFD simulation has been carried out to analyze the effect of injection timing on combustion process and emission characteristics in a four valves 2.0L Ford diesel engine. The calculation was performed from intake valve closing (IVC) to exhaust valve opening (EVO) at constant speed of 1600 rpm. Since the work was concentrated on the spray injection, mixture formation and combustion process, only a 60° sector mesh was employed for the calculations. For combustion modeling, an improved version of the Coherent Flame Model (ECFM-3Z) has been applied accompanied with advanced models for emission modeling. The results of simulation were compared against experimental data. Good agreement of calculated and measured in-cylinder pressure trace and pollutant formation trends were observed for all investigated operating points. In addition, the results showed that the current CFD model can be applied as a beneficial tool for analyzing the parameters of the diesel combustion under HSDI operating condition.

scholarly journals Experimental study of multiple pilot injection strategy in an automotive direct injection diesel engine

2018 ◽  
Vol 234 ◽  
pp. 03007
Author(s):  
Plamen Punov ◽  
Tsvetomir Gechev ◽  
Svetoslav Mihalkov ◽  
Pierre Podevin ◽  
Dalibor Barta
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Pilot Injection ◽  
Injection Strategy ◽  
Direct Injection Diesel Engine ◽  
Rate Of Heat Release

The pilot injection strategy is a widely used approach for reducing the noise of the combustion process in direct injection diesel engines. In the last generation of automotive diesel engines up to several pilot injections could occur to better control the rate of heat release (ROHR) in the cylinder as well as the pollutant formation. However, determination of the timing and duration for each pilot injection needs to be precisely optimised. In this paper an experimental study of the pilot injection strategy was conducted on a direct injection diesel engine. Single and double pilot injection strategy was studied. The engine rated power is 100 kW at 4000 rpm while the rated torque is 320 Nm at 2000 rpm. An engine operating point determined by the rotation speed of 1400 rpm and torque of 100 Nm was chosen. The pilot and pre-injection timing was widely varied in order to study the influence on the combustion process as well as on the fuel consumption.

Experimental and Theoretical Optimization of Combustion Chamber and Fuel Distribution for the Low Emission Direct-Injection Diesel Engine

2002 ◽  
Vol 125 (1) ◽  
pp. 351-357 ◽  
Author(s):  
Y. Kidoguchi ◽  
M. Sanda ◽  
K. Miwa
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Direct Injection ◽  
Combustion Process ◽  
Mixture Distribution ◽  
Initial Mixture ◽  
Injection Timing ◽  
Particulate Emissions ◽  
Particulate Emission ◽  
Direct Injection Diesel Engine

Effects of combustion chamber geometry and initial mixture distribution on the combustion process were investigated in a direct-injection diesel engine. In the engine experiment, a high squish combustion chamber with a squish lip could reduce both NOx and particulate emissions with retarded injection timing. According to the results of CFD computation and phenomenological modeling, the high squish combustion chamber with a central pip is effective to keep the combusting mixture under the squish lip until the end of combustion and the combustion region forms rich and highly turbulent atmosphere. This kind of mixture distribution tends to reduce initial burning, resulting in restraint of NOx emission while keeping low particulate emission.

scholarly journals Effects of pilot injection timing and EGR on a modern V6 common rail direct injection diesel engine

2013 ◽  
Vol 50 ◽  
pp. 012008 ◽  
Author(s):  
Nik Rosli Abdullah ◽  
Rizalman Mamat ◽  
Miroslaw L Wyszynski ◽  
Anthanasios Tsolakis ◽  
Hongming Xu
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Common Rail ◽  
Injection Timing ◽  
Pilot Injection ◽  
Direct Injection Diesel Engine

Effect of altitude conditions on combustion and performance of a turbocharged direct-injection diesel engine

2021 ◽  
pp. 095440702110262
Author(s):  
Zhentao Liu ◽  
Jinlong Liu
Keyword(s):  
Diesel Engine ◽  
High Altitude ◽  
Diesel Engines ◽  
Direct Injection ◽  
Pressure Rise ◽  
Ambient Conditions ◽  
Allowable Limit ◽  
Spray Formation ◽  
Direct Injection Diesel Engine ◽  
And Performance

Market globalization necessitates the development of heavy duty diesel engines that can operate at altitudes up to 5000 m without significant performance deterioration. But the current scenario is that existing studies on high altitude effects are still not sufficient or detailed enough to take effective measures. This study applied a single cylinder direct injection diesel engine with simulated boosting pressure to investigate the performance degradation at high altitude, with the aim of adding more knowledge to the literature. Such a research engine was conducted at constant speed and injection strategy but different ambient conditions from sea level to 5000 m in altitude. The results indicated the effects of altitude on engine combustion and performance can be summarized as two aspects. First comes the extended ignition delay at high altitude, which would raise the rate of pressure rise to a point that can exceed the maximum allowable limit and therefore shorten the engine lifespan. The other disadvantage of high-altitude operation is the reduced excess air ratio and gas density inside cylinder. Worsened spray formation and mixture preparation, together with insufficient and late oxidation, would result in reduced engine efficiency, increased emissions, and power loss. The combustion and performance deteriorations were noticeable when the engine was operated above 4000 m in altitude. All these findings support the need for further fundamental investigations of in-cylinder activities of diesel engines working at plateau regions.

On the Premixed Combustion in a Direct-Injection Diesel Engine

1987 ◽  
Vol 109 (2) ◽  
pp. 187-192 ◽  
Author(s):  
A. C. Alkidas
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Engine Speed ◽  
Direct Injection ◽  
Premixed Combustion ◽  
Injection Timing ◽  
Oxides Of Nitrogen ◽  
Nitrogen Emissions ◽  
Direct Injection Diesel Engine ◽  
Diffusion Burning

The factors influencing premixed burning and the importance of premixed burning on the exhaust emissions from a small high-speed direct-injection diesel engine were investigated. The characteristics of premixed and diffusion burning were examined using a single-zone heat-release analysis. The mass of fuel burned in premixed combustion was found to be linearly related to the product of engine speed and ignition-delay time and to be essentially independent of the total amount of fuel injected. Accordingly, the premixed-burned fraction increased with increasing engine speed, with decreasing fuel-air ratio and with retarding injection timing. The hydrocarbon emissions did not correlate well with the premixed-burned fraction. In contrast, the oxides of nitrogen emissions were found to increase with decreasing premixed-burned fraction, indicating that diffusion burning, and not premixed burning, is the primary source of oxides of nitrogen emissions.

Determination of the Start and End of Combustion in a Direct Injection Diesel Engine Using the Apparent Heat Release Rate

2017 ◽  
Author(s):  
Joseph Gerard T. Reyes ◽  
Edwin N. Quiros
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Start Of Combustion

The combustion duration in an internal combustion engine is the period bounded by the engine crank angles known as the start of combustion (SOC) and end of combustion (EOC), respectively. This period is essential in analysis of combustion for the such as the production of exhaust emissions. For compression-ignition engines, such as diesel engines, several approaches were developed in order to approximate the crank angle for the start of combustion. These approaches utilized the curves of measured in-cylinder pressures and determining by inspection the crank angle where the slope is steep following a minimum value, indicating that combustion has begun. These pressure data may also be utilized together with the corresponding cylinder volumes to generate the apparent heat release rate (AHRR), which shows the trend of heat transfer of the gases enclosed in the engine cylinder. The start of combustion is then determined at the point where the value of the AHRR is minimum and followed by a rapid increase in value, whereas the EOC is at the crank angle where the AHRR attains a flat slope prior to the exhaust stroke of the engine. To verify the location of the SOC, injection line pressures and fuel injection timing are also used. This method was applied in an engine test bench using a four-cylinder common-rail direct injection diesel engine with a pressure transducer installed in the first cylinder. Injector line pressures and fuel injector voltage signals per engine cycle were also recorded and plotted. By analyzing the trends of this curves in line with the generated AHRR curves, the SOC may be readily determined.

Low-sooting combustion in a small-bore high-speed direct-injection diesel engine using narrow-angle injectors

2008 ◽  
Vol 222 (10) ◽  
pp. 1927-1937 ◽  
Author(s):  
T-G Fang ◽  
R E Coverdill ◽  
C-F F Lee ◽  
R A White
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Fuel Efficiency ◽  
Operating Conditions ◽  
Injection Timing ◽  
Exhaust Pipe ◽  
Injection Angle ◽  
Direct Injection Diesel Engine ◽  
Combustion Flame

An optically accessible high-speed direct-injection diesel engine was used to study the effects of injection angles on low-sooting combustion. A digital high-speed camera was employed to capture the entire cycle combustion and spray evolution processes under seven operating conditions including post-top-dead centre (TDC) injection and pre-TDC injection strategies. The nitrogen oxide (NO x) emissions were also measured in the exhaust pipe. In-cylinder pressure data and heat release rate calculations were conducted. All the cases show premixed combustion features. For post-TDC injection cases, a large amount of fuel deposition is seen for a narrower-injection-angle tip, i.e. the 70° tip, and ignition is observed near the injector tip in the centre of the bowl, while for a wider-injection-angle tip, namely a 110° tip, ignition occurs near the spray tip in the vicinity of the bowl wall. The combustion flame is near the bowl wall and at the central region of the bowl for the 70° tip. However, the flame is more distributed and centralized for the 110° tip. Longer spray penetration is found for the pre-TDC injection timing cases. Liquid fuel impinges on the bowl wall or on the piston top and a fuel film is formed. Ignition for all the pre-TDC injection cases occur in a distributed way in the piston bowl. Two different combustion modes are observed for the pre-TDC injection cases including a homogeneous bulky combustion flame at earlier crank angles and a heterogeneous film combustion mode with luminous sooting flame at later crank angles. In terms of soot emissions, NO x emissions, and fuel efficiency, results show that the late post-TDC injection strategy gives the best performance.

Sign in / Sign up

Export Citation Format

Share Document