Finite Element Analysis of Dynamic Responses of Plain Concrete Pavements Under Strong Impact Loading

2013 ◽  
Vol 838-841 ◽  
pp. 23-29
Author(s):  
Xiao He Zhou ◽  
Da Wei Ma ◽  
Gui Gao Le
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Failure Mode ◽  
Impact Loading ◽  
Shear Failure ◽  
Plain Concrete ◽  
Dynamic Responses ◽  
Crack Model ◽  
Strong Impact ◽  
Concrete Pavements

Plain concrete pavements under heavy impact loading will induce flexure, crack and direct shear failure. To obtain dynamic response and failure mode of plain concrete pavement under heavy impact loading, the concrete brittle crack model is adopted and finite element model of plain concrete pavements is established; the dynamic response and failure mode under heavy impact loading in different loading points and different loading times are studied; the production, stretching and extension of cracking are researched; which is a powerful reference for practical engineering application.

Foundation Modeling for Jointed Concrete Pavements

2000 ◽  
Vol 1730 (1) ◽  
pp. 34-42 ◽  
Author(s):  
William G. Davids
Keyword(s):  
Finite Element ◽  
Temperature Gradient ◽  
Load Transfer ◽  
Plain Concrete ◽  
Positive Temperature ◽  
Concrete Pavements ◽  
Finite Element Program ◽  
Joint Load ◽  
Foundation Type ◽  
Dense Liquid

Issues related to the finite element modeling of base and subgrade materials under jointed plain concrete pavements are examined. The threedimensional finite element program EverFE, developed in conjunction with the Washington State Department of Transportation, was employed for the analyses. The relevant modeling capabilities of EverFE are detailed, including the ability to model multiple foundation layers, the incorporation of loss of contact between slab and base, and the efficient iterative solution strategies that make large three-dimensional finite element analyses possible on desktop computers. The results of parametric studies examining the effects of foundation type (layered elastic and dense liquid) and properties on the response of jointed plain concrete pavements subjected to axle and thermal loads are presented. Special attention is paid to the interactions between joint load transfer effectiveness and foundation type, and joint load transfer is shown to change significantly with different foundation models and properties. A consideration of simultaneous thermal and axle loadings indicates that the effect of foundation type and properties on critical slab stresses caused by edge loading and a positive temperature gradient is relatively small. However, the slab response is quite sensitive to foundation type for a combined negative temperature gradient and corner loading. On the basis of these results, use of an equivalent dense liquid foundation modulus in mechanistic rigid pavement analysis or design is not recommended when stiff base layers are present.

Dynamic Response and Shear Demand of Reinforced Concrete Beams Subjected to Impact Loading

2019 ◽  
Vol 19 (08) ◽  
pp. 1950091 ◽  
Author(s):  
Wuchao Zhao ◽  
Jiang Qian
Keyword(s):  
Dynamic Response ◽  
Impact Loading ◽  
Parametric Study ◽  
Shear Failure ◽  
Impact Force ◽  
Rc Beams ◽  
Local Response ◽  
Shear Demand ◽  
The Impact ◽  
Peak Impact Force

Reinforced concrete (RC) beams under the impact loading are typically prone to suffer shear failure in the local response phase. In order to enhance the understanding of the mechanical behavior of the RC beams, their dynamic response and shear demand are numerically investigated in this paper. A 3D finite-element model is developed and validated against the experimental data available in the literature. Taking advantage of the above calibrated numerical model, an intensive parametric study is performed to identify the effect of different factors including the impact velocity, impact mass and beam span-to-depth ratio on the impact response of the RC beams. It is found that, due to the inertial effect, a linear relationship exists between the maximum reverse support force and the peak impact force, while negative bending moments also appear in the shear span. In addition, the local response of the RC beams can be divided into a first impact stage and a separation stage. A shear plug is likely to be formed near the impact point at the first impact stage and a shear failure may be triggered near the support by large support forces. Based on the simulation results, simplified methods are proposed for predicting the shear demand for the two failure modes, whereas physical models are also established to illustrate the resistance mechanism of the RC beams at the peak impact force. By comparing with the results of the parametric study, it is concluded that the shear demand of the RC beams under the impact loading can be predicted by the proposed empirical formulas with reasonable accuracy.

scholarly journals A 3D Direct Vehicle-Pavement Coupling Dynamic Model and Its Application on Analysis of Asphalt Pavement Dynamic Response

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Peng Cao ◽  
Changjun Zhou ◽  
Decheng Feng ◽  
Youxuan Zhao ◽  
Baoshan Huang
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Dynamic Model ◽  
Static Analysis ◽  
Moving Load ◽  
Dynamic Responses ◽  
Pavement Surface ◽  
Coupling Dynamic ◽  
Pavement Structure ◽  
Coupling Dynamic Model

Currently dynamic response of the pavement structure is widely studied in pavement engineering. A 3D direct vehicle-pavement coupling dynamic model was developed to describe the pavement dynamic responses in this paper. The moving vehicle was simplified as spring-dashpot components, and the pavement structure was simulated using three-dimension finite element model. Based on Newton iteration and central difference integration algorithm, the static and dynamic coupling reactions between the pavement structure and vehicle were considered using finite element platform ABAQUS. The numerical results fit analytic results very well in static analysis and fit experiment results in dynamic analysis well too. The simulated results indicate that the dynamic pavement surface deflection is much higher than the situation in static analysis, due to the overlapping effect. This phenomenon enhances when vehicle speed increases. A discontinuous zone of shear stress was observed on the base surface between the location under moving load and the location the moving load just passed. It was also found that the vertical fluctuation exists on the vehicle even if there is no roughness on the pavement surface. In general, the developed 3-D direct vehicle-pavement coupling dynamic model was validated to be effective on evaluating pavement dynamic responses.

Dynamic Response and Failure Mode Analysis on Light-Weight Steel Columns under Blast Loads

2012 ◽  
Vol 166-169 ◽  
pp. 1489-1497 ◽  
Author(s):  
Shi Yan ◽  
Lei Liu ◽  
Peng Li ◽  
Zhi Qiang Xin ◽  
Bao Xin Qi
Keyword(s):  
Dynamic Response ◽  
Failure Mode ◽  
Failure Modes ◽  
Shear Failure ◽  
Mode Analysis ◽  
Material Strength ◽  
Light Weight ◽  
Blast Loads ◽  
Element Analysis ◽  
Steel Columns

The dynamic response and failure mode of light-weight steel columns under blast loads were studied in this paper by using nonlinear finite element analysis (FEA) software ANSYS/ LS-DYNA, aiming to develop the degree and modes of the excessive plastic deformation during failures of the columns under diverse parameters. The damaged columns with initial blast-induced deformation may evidently influence vertical stability of light-weight steel frame structures. During the numerical simulation, the element of three dimensional solid SOLID164 was used, and the strain rate effect on material strength was included in the material model with Plastic-Kinematic (MAT-03). The main parameters included in the analysis were boundary conditions, scaled distances of explosions, and the vertical compressive load ratios applied on tops of the columns. The results showed that the column with both two fixed ends was the most beneficial to resist blast shock wave, the horizontal displacement at the middle span of the columns were obviously decreasing as increasing of the scaled distances of the explosion, and the axial compression ratio only significantly influenced the column with a sliding end. The failure modes of the developed columns may be summarized as bending failure, direct shear failure, and bending shear combination failure.

Research on Load Transfer Efficiency of GFRP Dowel in Jointed Plain Concrete Pavement

2012 ◽  
Vol 178-181 ◽  
pp. 1152-1155 ◽  
Author(s):  
Luo Ke Li ◽  
Yun Liang Li ◽  
Yi Qiu Tan ◽  
Zhong Jun Xue
Keyword(s):  
Finite Element ◽  
Load Transfer ◽  
Concrete Slab ◽  
Three Dimensional ◽  
Plain Concrete ◽  
Element Model ◽  
Transfer Efficiency ◽  
Engineering Practice ◽  
Concrete Pavements ◽  
Load Transfer Efficiency

In a jointed plain concrete pavements, the dowel bar system are used to provide lateral load transfer across transverse joint. Corrosion of commonly used steel dowel in engineering practice reduces their service life and costs considerable maintenance and repair spending for concrete pavements. The objective of this study focus primarily on the performance of none eroded GFRP dowel on LTE( load transfer efficiency) with the help of a three-dimensional finite-element model. The amount of LTE can be obtained directly from comparing the maximum deflection of the concrete slab and the level tensile stress under the concrete slab. According to the finite element results, the larger-diameter GFRP dowel are found to perform the best in this study.

scholarly journals Effectiveness of Dowels in Concrete Pavement

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1669 ◽  
Author(s):  
Jiri Grosek ◽  
Andrea Zuzulova ◽  
Ilja Brezina
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Load Transfer ◽  
Plain Concrete ◽  
Concrete Pavement ◽  
Successful Outcome ◽  
Concrete Pavements ◽  
The Finite Element Method ◽  
Improve Performance ◽  
Direct Measurements

Dowels are located in transverse joints of Jointed Plain Concrete Pavements (JPCP) and they are used to provide load transfer between individual slabs, reduce faulting and improve performance. Dowels and the concrete itself are under the highest stress in the vicinity of joints; thus, in terms of pavement design, the joints are the weakest points of the whole structure. This study dealt with the drawbacks of JPCP with dowels. The evaluation was based on direct measurements on real airport and motorway pavements and highlights insufficient efficiency of load transfer and its possible causes. The authors present a successful outcome with validation by using the finite element method where high tensile stress values of the surrounding concrete were found.

scholarly journals Dynamic Responses of a Twin-Tunnel Subjected to Moving Loads in a Saturated Half-Space

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Hong-lei Sun ◽  
An-hua Chen ◽  
Li Shi ◽  
Xue-yu Geng ◽  
Yu Wang
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Saturated Porous Medium ◽  
Moving Load ◽  
Surrounding Medium ◽  
Element Model ◽  
Dynamic Responses ◽  
3D Finite Element ◽  
Twin Tunnel ◽  
Tunnel Model

With the fast development of rail transit, the environmental vibration problems caused by subways have received increasing attention. A 3D finite element model was built in this study to investigate the ground vibrations induced by the moving load operating in the parallel twin tunnels. Compared to the model consisting of a single tunnel that was commonly adopted in the past studies, a pair of tunnels is considered and the surrounding medium of the tunnels is taken as a saturated porous medium. The governing equations of the 3D finite element method modeling of the saturated poroelastic soil have been derived according to Biot’s theory. Computed results showed that the dynamic response of the twin-tunnel model is greater than that of the single tunnel model. And the spacing between two tunnels, tunnel buried depth, and load moving speed are the essential parameters to determine the dynamic response of the tunnel and soil.

scholarly journals Experiment and Numerical Simulation of the Dynamic Response of Bridges under Vibratory Compaction of Bridge Deck Asphalt Pavement

2019 ◽  
Vol 2019 ◽  
pp. 1-16 ◽  
Author(s):  
An-Ping Peng ◽  
Han-Cheng Dan ◽  
Dong Yang
Keyword(s):  
Finite Element ◽  
Dynamic Response ◽  
Field Experiments ◽  
Bridge Deck ◽  
Asphalt Pavement ◽  
Dynamic Responses ◽  
Structural Safety ◽  
Cross Sectional ◽  
Bridge Structures ◽  
Vibratory Compaction

Vibratory compaction of bridge deck pavement impacts the structural integrity of bridges to certain degrees. In this study, we analyzed the dynamic response of different types of concrete-beam bridges (continuous beam and simply supported beam) with different cross-sectional designs (T-beam and hollow-slab beam) under vibratory compaction of bridge deck asphalt pavement. The dynamic response patterns of the dynamic deformation and acceleration of bridges under pavement compaction were obtained by performing a series of field experiments and a three-dimensional finite element simulation. Based on the finite element model, the dynamic responses of bridge structures with different spans and cross-sectional designs under different working conditions of vibratory compaction were analyzed. The use of different vibration parameters for different bridge structures was proposed to safeguard their structural safety and reliability.

Sign in / Sign up

Export Citation Format

Share Document