Drying of Rubber Sheet Using Impingement of Multiple Hot Air Jets

2013 ◽  
Vol 844 ◽  
pp. 502-506 ◽  
Author(s):  
Chayut Nuntadusit ◽  
Makatar Waehahyee
Keyword(s):  
Heat Transfer ◽  
Moisture Content ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Drying Rate ◽  
Rubber Sheet ◽  
Air Jets ◽  
Hot Air ◽  
Rubber Surface ◽  
Jet Velocity

In the process for producing ribbed smoked rubber sheet, the rubber sheet drying is the most time and energy consumption process. This research study the possibility in develop new drying system using array of hot air jets impinging directly on rubber sheet in order to reduce time for drying rubber in smoked room and increase productivity of rubber sheets. In the study, the array of jets from jet plate with drilled jet holes in staggered arrangement impinged on the both side of rubber sheet. The effects of jet velocity (Vj=10, 16, 23 m/s), jet temperature (Tj=50, 60, 70°C) and the distance from jet outlet to rubber surface (L=4D, 6D, 8D which D is diameter of jet hole) on drying rate were investigated by measuring weight of rubber sheet change with time. The heat transfer rate on impinged surface was also measured by attaching a heat flux sensor on impinged wall. The results showed that the convective heat transfer coefficient increased when the jet velocity was increased and when the distance from jet was decreased particularly in jet directly impinged region. It was found that the enhancement in heat transfer rate from jets cannot increase the rubber drying rate for all cases because the drying rate depend on rubber property. The process of rubber sheet drying can be divided in 2 periods; in the first drying period, the drying rate decreases with decreased moisture content. The drying rate depended on the initial moisture content and the condition of external effect such as jet velocity, jet temperature and distance from jet outlet to rubber surface. In second drying period, the moisture content is below 20% dry basis. In this period, the drying rate is almost constant near zero. It was also found that the drying for case of L=6D was higher than case of L=4D and 8D. The optimum condition for rubber sheet drying without defects on rubber property after drying was L=6D and Tj=70°C.

Drying Model, Shrinkage and Energy Consumption Evaluation of Air Dried Sheet Rubber Drying System for Small Enterprise

2012 ◽  
Vol 622-623 ◽  
pp. 1135-1139 ◽  
Author(s):  
A. Ekphon ◽  
T. Ninchuewong ◽  
S. Tirawanichakul ◽  
Y. Tirawanichakul
Keyword(s):  
Experimental Data ◽  
Energy Consumption ◽  
Moisture Content ◽  
Specific Energy ◽  
Experimental Results ◽  
Drying Rate ◽  
Rubber Sheet ◽  
Drying Temperature ◽  
Hot Air ◽  
Air Convection

The main objective of this research was to study drying kinetics of air dried sheet (ADS) rubber using hot air and simulated drying kinetics by empirical model compared to experimental results. The 10-15 fresh rubber sheet with initial moisture content ranging of 23-40% dry-basis was dried by temperature of 40-70°C and air flow rate of 0.7 m/s. The fresh rubber sheet samples were dried until the desired final moisture content reached to 0.15% dry-basis. The experimental results showed that the drying rate of ADS rubber dried with hot air convection was faster than conventional natural air convection and drying rate was related to drying temperature. The experimental data was statistical non-linear regression analyzed by using 10 conventional empirical models. The coefficient of determination (R2) and root mean square error (RMSE) values were used as the criteria for selecting the best equation to describe the experimental data The results showed that the calculated results of Verma et al.’ model had a good relation to the experimental results. For specific energy evaluation, the results showed that at high drying temperature specific energy consumption of ADS rubber was relatively low compared to drying with low temperature. Finally, the determination of physical quality showed that.

Ferro-nanofluid squeeze film lubrication with heat transfer

2021 ◽  
pp. 135065012110276
Author(s):  
Manimegalai Kavarthalai ◽  
Vimala Ponnuswamy
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Contact Time ◽  
Transfer Rate ◽  
Fluid Layer ◽  
Darcy Law ◽  
Squeeze Film ◽  
Mean Temperature ◽  
Special Cases ◽  
The Impact

A theoretical study of a squeezing ferro-nanofluid flow including thermal effects is carried out with application to bearings and articular cartilages. A representational geometry of the thin layer of a ferro-nanofluid squeezed between a flat rigid disk and a thin porous bed is considered. The flow behaviours and heat transfer in the fluid and porous regions are investigated. The mathematical problem is formulated based on the Neuringer–Rosensweig model for ferro-nanofluids in the fluid region including an external magnetic field, Darcy law for the porous region and Beavers–Joseph slip condition at the fluid–porous interface. The expressions for velocity, fluid film thickness, contact time, fluid flux, streamlines, pathlines, mean temperature and heat transfer rate in the fluid and porous regions are obtained by using a perturbation method. An asymptotic solution for the fluid layer thickness is also presented. The problem is also solved by a numerical method and the results by asymptotic analysis, perturbation and numerical methods are obtained assuming a constant force squeezing state and are compared. It is shown that the results obtained by all the methods agree well with each other. The effects of various parameters such as Darcy number, Beavers–Joseph constant and magnetization parameter on the flow behaviours, contact time, mean temperature and heat transfer rate are investigated. The novel results showing the impact of using ferro-nanofluids in the two applications under consideration are presented. The results under special cases are further compared with the existing results in the literature and are found to agree well.

scholarly journals Significance of Shape Factor in Heat Transfer Performance of Molybdenum-Disulfide Nanofluid in Multiple Flow Situations; A Comparative Fractional Study

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3711
Author(s):  
Asifa ◽  
Talha Anwar ◽  
Poom Kumam ◽  
Zahir Shah ◽  
Kanokwan Sitthithakerngkiet
Keyword(s):  
Heat Transfer ◽  
Skin Friction ◽  
Molybdenum Disulfide ◽  
Heat Transfer Rate ◽  
Shape Factor ◽  
Transfer Rate ◽  
Maximum Heat ◽  
Left Wall ◽  
Maximum Heat Transfer ◽  
Mos2 Nanoparticles

In this modern era, nanofluids are considered one of the advanced kinds of heat transferring fluids due to their enhanced thermal features. The present study is conducted to investigate that how the suspension of molybdenum-disulfide (MoS2) nanoparticles boosts the thermal performance of a Casson-type fluid. Sodium alginate (NaAlg) based nanofluid is contained inside a vertical channel of width d and it exhibits a flow due to the movement of the left wall. The walls are nested in a permeable medium, and a uniform magnetic field and radiation flux are also involved in determining flow patterns and thermal behavior of the nanofluid. Depending on velocity boundary conditions, the flow phenomenon is examined for three different situations. To evaluate the influence of shape factor, MoS2 nanoparticles of blade, cylinder, platelet, and brick shapes are considered. The mathematical modeling is performed in the form of non-integer order operators, and a double fractional analysis is carried out by separately solving Caputo-Fabrizio and Atangana-Baleanu operators based fractional models. The system of coupled PDEs is converted to ODEs by operating the Laplace transformation, and Zakian’s algorithm is applied to approximate the Laplace inversion numerically. The solutions of flow and energy equations are presented in terms of graphical illustrations and tables to discuss important physical aspects of the observed problem. Moreover, a detailed inspection on shear stress and Nusselt number is carried out to get a deep insight into skin friction and heat transfer mechanisms. It is analyzed that the suspension of MoS2 nanoparticles leads to ameliorating the heat transfer rate up to 9.5%. To serve the purpose of achieving maximum heat transfer rate and reduced skin friction, the Atangana-Baleanu operator based fractional model is more effective. Furthermore, it is perceived that velocity and energy functions of the nanofluid exhibit significant variations because of the different shapes of nanoparticles.

scholarly journals Assessment of TiO2 Nanoconcentration and Twin Impingement Jet of Heat Transfer Enhancement—A Statistical Approach Using Response Surface Methodology

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 595
Author(s):  
Mahir Faris Abdullah ◽  
Rozli Zulkifli ◽  
Hazim Moria ◽  
Asmaa Soheil Najm ◽  
Zambri Harun ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Tio2 Nanoparticle ◽  
Experimental Results ◽  
Improvement Rate ◽  
Design Expert ◽  
Impingement Jet

Impinging jets are considered to be a well-known technique that offers high local heat transfer rates. No correlation could be established in the literature between the significant parameters and the Nusselt number, and investigation of the interactions between the correlated factors has not been conducted before. An experimental analysis based on the twin impingement jet mechanism was achieved to study the heat transfer rate pertaining to the surface plate. In the current paper, four influential parameters were studied: the spacing between nozzles, velocity, concentration of Nano solution coating and nozzle-plate distance, which are considered to be effective parameters for the thermal conductivity and the heat transfer coefficient of TiO2 nanoparticle, an X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis were done, which highlighted the structure and showed that the nanosolution coated the surface homogenously. Moreover, a comparison was done for the experimental results with that of the predicted responses generated by the Design Expert software, Version 7 User’s Guide, USA. A response surface methodology (RSM) was employed to improve a mathematical model by accounting for a D-optimal design. In addition, the analysis of variance (ANOVA) was employed for testing the significance of the models. The maximum Nu of 91.47, where H = S = 1 cm; Reynolds number of 17,000, and TiO2 nanoparticle concentration of 0.5% M. The highest improvement rate in Nusselt was about 26%, achieved with TiO2 Nanoparticle, when S = 3 cm, H = 6 cm and TiO2 nanoparticle = 0.5 M. Furthermore, based on the statistical analysis, the expected values were found to be in satisfactory agreement with that of the empirical data, which was conducted by accounting for the proposed models’ excellent predictability. Multivariate approaches are very useful for researchers, as well as for applications in industrial processes, as they lead to increased efficiency and reduced costs, so the presented results of this work could encourage the overall uses of multivariate methods in these fields. Hypotheses: A comparison was done for the predicted responses generated by the Design Expert software with the experimental results and then studied to verify the following hypotheses: ► Preparation of three concentrations of TiO2 nanosolution was done and studied. ► The heat transfer rate could be increased by surface coating with TiO2 nanoparticle. ► The heat transfer could be improved by the impingement jet technique with suitable adjustments.

scholarly journals Heat Transmission Reinforcers Induced by MHD Hybrid Nanoparticles for Water/Water-EG Flowing over a Cylinder

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 623
Author(s):  
Firas A. Alwawi ◽  
Mohammed Z. Swalmeh ◽  
Amjad S. Qazaq ◽  
Ruwaidiah Idris
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Liquid Velocity ◽  
Flow Characteristics ◽  
Hybrid Nanoparticles ◽  
Critical Parameters ◽  
Heat Transmission ◽  
Constant Wall Temperature

The assumptions that form our focus in this study are water or water-ethylene glycol flowing around a horizontal cylinder, containing hybrid nanoparticles, affected by a magnetic force, and under a constant wall temperature, in addition to considering free convection. The Tiwari–Das model is employed to highlight the influence of the nanoparticles volume fraction on the flow characteristics. A numerical approximate technique called the Keller box method is implemented to obtain a solution to the physical model. The effects of some critical parameters related to heat transmission are also graphically examined and analyzed. The increase in the nanoparticle volume fraction increases the heat transfer rate and liquid velocity; the strength of the magnetic field has an adverse effect on liquid velocity, heat transfer, and skin friction. We find that cobalt nanoparticles provide more efficient support for the heat transfer rate of aluminum oxide than aluminum nanoparticles.

Sign in / Sign up

Export Citation Format

Share Document