Synthesis and Electrical Conductivity Measurement of Polyaniline / Vermiculite Nanocomposites

2010 ◽  
Vol 96 ◽  
pp. 221-226
Author(s):  
Hong Juan Sun ◽  
Ying Liu ◽  
Tong Jiang Peng ◽  
Hai Feng Liu ◽  
Jin Mei Sun
Keyword(s):  
Electrical Conductivity ◽  
Interlayer Space ◽  
In Situ Polymerization ◽  
Conductivity Measurement ◽  
Ammonium Bromide ◽  
X Ray Diffraction ◽  
Electrical Conductivity Measurement ◽  
X Ray ◽  
Dimethyl Ammonium

A series of polyaniline/vermiculite nanocomposites was synthesized. The interlayer space of vermiculite was initially increased by the insertion of dioctadecyl dimethyl ammonium bromide, and then the aniline monomers were inserted into the interlayer space of vermiculite replacing dioctadecyl dimethyl ammonium cations. The polyaniline/vermiculite nanocomposites materials were prepared via in situ polymerization of the aniline monomers in the interlayer space of vermiculite. The as-synthesized polyaniline/vermiculite nanocomposite materials were characterized by X-ray diffraction analysis, infrared spectroscopy, and electrical conductivity measurement. The results indicated that the vermiculite was peeled off into the polyaniline. The introduction of vermiculite nanosheets showed a beneficial effect on the electrical conductivity of polyaniline.

Synthesis and Characterization of the PANI/ITO Conducting Nanocomposites

2010 ◽  
Vol 663-665 ◽  
pp. 542-545 ◽  
Author(s):  
Bing Jie Zhu ◽  
Xin Wei Wang ◽  
Mei Fang Zhu ◽  
Qing Hong Zhang ◽  
Yao Gang Li ◽  
...  
Keyword(s):  
Doping Concentration ◽  
In Situ Polymerization ◽  
Synthesis And Characterization ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
X Ray ◽  
Maximum Conductivity ◽  
Scanning Electron

The PANI/ITO conducting nanocomposites have been synthesized by in-situ polymerization. The obtained nanocomposites were characterized by X-ray diffraction pattern, scanning electron microscopy and Fourier transform infrared. Electrical conductivity measurements on the samples pressed into pellets showed that the maximum conductivity attained 2.0 ± 0.05 S/cm for PANI/ITO nanocomposites, at ITO doping concentration of 10 wt%. The results of the present work may provide a simple, rapid and efficient approach for preparing PANI/ITO nanocomposites.

Dehydration and decomposition of pyrophyllite at high pressures: electrical conductivity and X-ray diffraction studies to 5 GPa

1997 ◽  
Vol 34 (6) ◽  
pp. 875-882 ◽  
Author(s):  
Tara L. Hicks ◽  
Richard A. Secco
Keyword(s):  
Electrical Conductivity ◽  
South African ◽  
Pressure Dependence ◽  
High Pressures ◽  
Ionic Conduction ◽  
Temperature Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Dependence Of Conductivity

The dehydration and decomposition of South African pyrophyllite were studied in the pressure range 2.5–5.0 GPa and in the temperature (T) range 295–1473 K using both in situ electrical conductivity measurements and X-ray diffraction studies on the recovered samples. Activation energies for conduction (Qc) vary in the range 0.02–0.07 eV for T ≤ 500 K where the dominant conduction mode is electronic, and Qc is in the range 1.10–1.28 eV for T ≥ 500 K where ionic conduction dominates. Abrupt changes in the isobaric temperature dependence of conductivity mark the onset of dehydration and subsequent decomposition into kyanite plus quartz–coesite. At 2.5 GPa, South African pyrophyllite forms the dehydroxylate phase at 760 K with a pressure dependence of ~30 K/GPa and complete decomposition follows at 1080 K with a pressure dependence of ~41 K/GPa. The resulting pressure–temperature phase diagram is in very good agreement with many previous studies at 1 atm (101.325 kPa).

Morphology of Polyethylene/Montmorillonite Nanocomposites Prepared by In Situ Polymerization

2013 ◽  
Vol 457-458 ◽  
pp. 244-247
Author(s):  
Min Li ◽  
Li Guang Xiao ◽  
Hong Kai Zhao
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reflection Peak ◽  
Basal Reflection ◽  
Scanning Electron

Polyethylene/montmorillonite (PE/MMT) nanocomposites were prepared by in situ polymerization. The morphology of MMT/MgCl2/TiCl4 catalyst and PE/MMT nanocomposites was investigated by scanning electron microscopy (SEM). It can be seen that MMT/MgCl2/TiCl4 catalyst remained the original MMT sheet structures and many holes were found in MMT and the morphology of PE/MMT nanocomposites is part of the sheet in the form of existence, as most of the petal structure. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were carried out to characterize all the samples. XRD results reveal that the original basal reflection peak of PEI1 and PEI2 disappears completely and that of PEI3 become very weak. MMT/MgCl2/TiCl4 catalyst was finely dispersed in the PE matrix. Instead of being individually dispersed, most layers were found in thin stacks comprising several swollen layers.

MECHANICAL PROPERTIES OF A POLYURETHANE/MONTMORILLONITE NANOCOMPOSITE FEATURING ORGANOMODIFICATION SYNTHESIZED VIA IN SITU POLYMERIZATION

2015 ◽  
Vol 88 (1) ◽  
pp. 138-146 ◽  
Author(s):  
Rouhollah Bagheri ◽  
Reza Darvishi
Keyword(s):  
Mechanical Properties ◽  
In Situ Polymerization ◽  
Xrd Analysis ◽  
Silicate Layer ◽  
X Ray Diffraction ◽  
X Ray ◽  
End Groups ◽  
Layer Sample ◽  
Silicate Layers

ABSTRACT In this study, polyurethane (PU)/organomodified montmorillonite (cloisite®30B) is synthesized via in situ polymerization by reaction of an ether-based prepolymer with the isocyanate end groups and adiamine chain extender (4, 4-methylene-bis(2-chloroaniline)) in the presence of different amounts of nanoparticles dispersed in the prepolymer matrix by an ultrasonic mixer for 1 h. The synthesized polymers are cast on a pretreated carbon steel sheet and cured at 120 °C in an oven. The PU and its composites have been characterized by using Fourier transform infrared spectroscopy, X-ray diffraction (XRD), and mechanical testing. The XRD analysis of the cured samples containing 1 to 3 wt% cloisite30B showed intercalation segments in the silicate layers and exfoliation for 0.5 wt% nanoparticles. The highest mechanical properties were obtained using the cured exfoliated silicate layer sample. A twofold increase in the ultimate tensile strength and a 2.3 times increase in the adhesion strength were found for 0.5 wt% organoclay/PU as compared with that of pure PU. In addition, the exfoliated structure sample exhibited a 16% reduction in abrasion compared with that of pure PU.

In Situ Polymerization and Characterization of Poly(ε-caprolactone)/Layered Double Hydroxide Nanocomposites

2012 ◽  
Vol 557-559 ◽  
pp. 371-374
Author(s):  
Lian Liu ◽  
Teng Yu ◽  
Pei Wang ◽  
Guang Shuo Wang
Keyword(s):  
Layered Double Hydroxide ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Visible ◽  
Absorbance Peak ◽  
Double Hydroxide

Nanocomposites of poly(ε-caprolactone) (PCL) and layered double hydroxide (LDH) were prepared by in situ polymerization at low LDHs loadings in this work. The resultants were characterized by FTIR spectroscopy, X-ray diffraction (XRD), differential scanning calorimeter (DSC) and UV-visible spectroscopy (UV-vis). FTIR showed that the PCL/LDHs nanocomposites were prepared successfully by in situ polymerization and XRD spectra showed that the crystal structure did not change greatly in the presence of LDHS. DSC results confirmed that LDHs could act as nucleating agents. UV-vis spectra showed that LDHs had stronger absorbance peak than LDH. Moreover, the PCL/LDHs nanocomposites had strong anti-ultraviolet effect by introduction of LDHs into polymer matrix.

IN SITU SYNTHESIS, CHARACTERIZATION AND FREQUENCY DEPENDENT AC CONDUCTIVITY OF POLYANILINE/CoFe2O4 NANOCOMPOSITES

2011 ◽  
Vol 01 (03) ◽  
pp. 357-362 ◽  
Author(s):  
G. D. PRASANNA ◽  
H. S. JAYANNA
Keyword(s):  
Ac Conductivity ◽  
Room Temperature ◽  
In Situ Polymerization ◽  
In Situ Synthesis ◽  
Electron Micrograph ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Scanning Electron Micrograph ◽  
X Ray

The polyaniline (PANI)/ CoFe2O4 nanocomposites were prepared by an In Situ polymerization of aniline in an aqueous solution. The composites were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectrum,thermogravimetric analysis (TGA) and scanning electron micrograph (SEM). The AC conductivity and dielectric properties of these composites were investigated in the frequency range 1 kHz–10 MHz at room temperature. The AC conductivity was found to be constant up to 1 MHz and thereafter it increases steeply and it was observed maximum for the PANI with 60 wt% of CoFe2O4 nanocomposite. At lower frequencies the values of dielectric constant is maximum for pure CoFe2O4 nanoparticles.

scholarly journals The In Situ Polymerization and Characterization of PA6/LiCl Composites

2013 ◽  
Vol 2013 ◽  
pp. 1-4 ◽  
Author(s):  
Dandan Sun ◽  
Jiang Li ◽  
Qinghua Pan ◽  
Chaowei Hao ◽  
Guoqiao Lai
Keyword(s):  
Sodium Hydroxide ◽  
Anionic Polymerization ◽  
In Situ Polymerization ◽  
Degree Of Crystallinity ◽  
Inorganic Salts ◽  
X Ray Diffraction ◽  
X Ray ◽  
Phase Proportion

PA6/LiCl composites were synthesized by in situ anionic polymerization based on the interaction between the inorganic salts and PA6. Sodium hydroxide as initiator and N-acetylcaprolactam as activator were used in the preparation of PA6/LiCl composites with variety of LiCl content. X-ray diffraction (XRD) and differential scanning calorimeter (DSC) testing results showed that both of degree of crystallinity and melting temperature of the composites were decreased under the influence of LiCl. And theγcrystal phase proportion increased with increasing the LiCl content to appropriate amount.

Preparation and Characteristic of PSMA/EG Composite Materials

2010 ◽  
Vol 163-167 ◽  
pp. 1951-1954
Author(s):  
Gui Xiang Hou ◽  
Hai Ning Na ◽  
Xiao Ming Sang
Keyword(s):  
High Temperature Oxidation ◽  
In Situ Polymerization ◽  
Expanded Graphite ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Temperature Oxidation ◽  
X Ray ◽  
Graphite Nanosheets ◽  
Composite Granules

Graphite nanosheets prepared through high-temperature oxidation via powdering the expanded graphite. After soaking the expanded graphite with styrene(S) and maleic anhydride(MA) monomers, the polymer (Poly(S-co-MA))/expanded graphite(EG) (PSMA/EG) composite granules were obtained by in situ polymerization. Light microscope，scanning electron microscope and X-ray diffraction characterization were performed. SEM analysis indicate that the expanded graphite was mostly tore to sheets with thickness of 50–80 nm and with diameter of 1μm. Optical micrographs showed that the distribution of graphite platelets is found to be nearly uniform.

scholarly journals A Study of Crystallographic and DC Electrical Characteristics of PPy/Ag Nanocomposites

2021 ◽  
Vol 19 (49) ◽  
pp. 15-21
Author(s):  
Mohammed Abdilridha Salman ◽  
Salma M. Hassan
Keyword(s):  
In Situ Polymerization ◽  
Orthorhombic Symmetry ◽  
Electrical Characteristics ◽  
Monoclinic Structure ◽  
X Ray Diffraction ◽  
Ammonium Persulphate ◽  
X Ray ◽  
Weight Percentage ◽  
Nm Range

ABSTRACT: Polypyrrole and polypyrrole / silver nanocomposites were fabricated by in-situ polymerization employing Ammonium Persulphate as an oxidizing agent. Nanocomposites were synthesized by combining polypyrrole and silver nanoparticles in various weight percentages (0.1%, 0.5%, 3%, 5% and 7% wt.). Crystallographic data were collected using X-ray diffraction.  PPy particles were found to have an orthorhombic symmetry. In contrast, PPy/Ag nanocomposites were reported to have monoclinic structure. The crystallite size was determined by XRD using Scherrer equation and considered to be within 49 nm range. DC conductivity of pelletized samples was evaluated in the temperature range of 323.15k to 453.15k. The conductivity displayed an increase when the temperature is increased from 323.15k to 453.15k. Activation energies were determined from plots of Arrhenius for all nanocomposites. The findings indicated that the activation energy decrease with increasing the weight percentage of Ag nanoparticles in the nanocomposites.

scholarly journals Thermal and electrical properties of polyimide/PANI nanofiber composites prepared via in situ polymerization

2018 ◽  
Vol 36 (2) ◽  
pp. 283-287
Author(s):  
Aseel A. Kareem
Keyword(s):  
In Situ Polymerization ◽  
Composite Films ◽  
Nanocomposite Films ◽  
X Ray Diffraction ◽  
Nanofiber Composite ◽  
X Ray ◽  
Thermal And Electrical Properties ◽  
Ft Ir ◽  
Thermal Stability Of

Abstract Polyimide/polyaniline nanofiber composites were prepared by in situ polymerization with various weight percentages of polyaniline (PANI) nanofibers. X-ray diffraction (XRD) and Fourier transform infrared spectra (FT-IR), proved the successful preparation of PANI nanofiber composite films. In addition, thermal stability of PI/PANI nanofiber composites was superior relative to PI, having 10 % gravimetric loss in the range of 623 °C to 671 °C and glass transition temperature of 289 °C to 297 °C. Furthermore, the values of the loss tangent tanδ and AC conductivity σAC of the nanocomposite films were notably higher than those of pure polyimide. The addition of 5 wt.% to 15 wt.% PANI nanofiber filler enhanced the activation energy of PI composites from 0.37 eV to 0.34 eV.

Sign in / Sign up

Export Citation Format

Share Document