Effect of Cerium Addition on the Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy

2008 ◽  
Vol 279 ◽  
pp. 97-103 ◽  
Author(s):  
Anil K. Chaubey ◽  
S. Mohapatra ◽  
B. Bhoi ◽  
J.L. Gumaste ◽  
Barada Kanta Mishra ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Grain Refinement ◽  
Strengthening Mechanism ◽  
Casting Method ◽  
Cu Alloy ◽  
Microstructure And Mechanical Properties ◽  
Cast Alloys ◽  
Mould Casting

Al–8.6Zn–2.6Mg-2.4Cu–xCe(x = 0–0.4 wt. %) alloys were prepared by metal mould casting method, the effects of Ce on the microstructure and mechanical properties of the alloys were investigated. The results showed that the dendrite as well as grain size were refined by the addition of Ce, and the best refinement was obtained in 0.25 wt % Ce containing alloy. The main phases in the as-cast alloys were α-Al, Mg-Zn32, Mg32 (Al, Zn)49, and Al4Ce phase was found in the alloys containing more than 0.1%Ce. The addition of Ce improved the mechanical properties of the alloys. The strengthening mechanism was attributed to grain refinement and compound reinforced

Microstructure and Mechanical Properties of Mg-1Mn-0.6Ce Alloy Containing Yttrium

2011 ◽  
Vol 391-392 ◽  
pp. 638-641
Author(s):  
G.H. Su ◽  
Y. Sun ◽  
Zhan Yi Cao
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Yield Strength ◽  
Mass Fraction ◽  
Room Temperature ◽  
Precipitation Strengthening ◽  
Casting Method ◽  
Microstructure And Mechanical Properties ◽  
Cast Alloys

Mg-1Mn-0.6Ce-xY (x=0, 1, 2 and 3, mass fraction, %) magnesium alloys were prepared by casting method. And the influences of yttrium on microstructure and mechanical properties of the Mg-1Mn-0.6Ce magnesium alloy were investigated. The results reveal that the addition of yttrium to the Mg-1Mn-0.6Ce alloy could reduce the grain size of the as-cast alloys and improve mechanical properties during the investigated temperature range. The Mg-1Mn-0.6Ce-1Y alloy exhibits maximum ultimate strength, yield strength, elongation and the values are 152 MPa, 72 MPa and 13.4% and enhanced about 23.1%, 63.6% and 38.1% compared with those of Mg-1Mn-0.6Ce alloy at room temperature, respectively. The improvement of mechanical properties are attributed to the grain refinement and the precipitation strengthening generated by the Mg12Ce phase particles and the fine Mg24Y5 precipitations.

Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy

2017 ◽  
Vol 898 ◽  
pp. 124-130 ◽  
Author(s):  
Shu Min Xu ◽  
Xin Ying Teng ◽  
Xing Jing Ge ◽  
Jin Yang Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Second Phase ◽  
Casting Method ◽  
Magnesium Matrix ◽  
Microstructure And Mechanical Properties

In this paper, the microstructure and mechanical properties of the as-cast and heat treatment of Mg-Zn-Nd alloy was investigated. The alloy was manufactured by a conventional casting method, and then subjected to a heat treatment. The results showed that the microstructure of as-cast alloy was comprised of α-Mg matrix and Mg12Nd phase. With increase of Nd content, the grain size gradually decreased from 25.38 μm to 9.82 μm. The ultimate tensile strength and elongation at room temperature of the Mg94Zn2Nd4 alloy can be reached to 219.63 MPa and 5.31%. After heat treatment, part of the second phase dissolved into the magnesium matrix and the grain size became a little larger than that of the as-cast. The ultimate tensile strength was declined by about 2.5%, and the elongation was increased to 5.47%.

Microstructure and Mechanical Properties of Extruded Mg-Al-Ca Based Alloys

2005 ◽  
Vol 488-489 ◽  
pp. 275-278 ◽  
Author(s):  
Rong Shi Chen ◽  
Jean Jacques Blandin ◽  
Michel Suéry ◽  
En Hou Han
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Elevated Temperature ◽  
Yield Strength ◽  
Ambient Temperature ◽  
Grain Refinement ◽  
Tensile Tests ◽  
Az91 Alloy ◽  
Microstructure And Mechanical Properties ◽  
Ca Addition

Mechanical properties and microstructure of extruded AZ91(-Ca) alloys have been studied in this paper. The results showed that Ca has no significant effect on reducing grain size of the extruded AZ91 alloy. The ambient temperature tensile tests showed that the ultimate and yield strength of extruded AZ91 alloy decreased by addition of Ca. At elevated temperature, Ca addition improves the yield strength of both AZ91 alloy. The variations in microstructure and mechanical properties of the AZ91 alloy are also discussed in terms of the effects of Ca on grain refinement and formation of constituent phases.

Effect of La-Rich Misch Metal on Microstructure and Mechanical Properties of As-Extruded Mg-14Li-3Al Alloy

2011 ◽  
Vol 391-392 ◽  
pp. 32-36 ◽  
Author(s):  
Bin Liu ◽  
Jing Huai Zhang ◽  
Zhong Yi Niu ◽  
Jun Qing Li
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Properties ◽  
Grain Refinement ◽  
Hot Extrusion ◽  
Vacuum Melting ◽  
Melting Method ◽  
Misch Metal ◽  
Microstructure And Mechanical Properties

The as-cast Mg-14Li-3Al-(0-0.9)RE alloys were prepared with vacuum melting method, then processed by hot extrusion. The microstructure and tensile properties were investigated. The results show that both addition of RE and extrusion deformation can refine the grain size. Al3La compounds are formed with addition of La-rich misch metal. The as-extruded Mg-14Li-3Al-0.6RE alloy obtains the finest grain size (4.28 μm) and the highest mechanical properties (σb=222.75 MPa, δ=23.8%), which is related to the grain refinement and the formation of Al3La.

Effect of Trace Boron on Microstructure and Mechanical Properties of Ti-9V-3Al-3Cr-3Zr-3.5Mo Alloy

2011 ◽  
Vol 194-196 ◽  
pp. 1287-1290
Author(s):  
Xu Liang Liu ◽  
Yun Qing Ma ◽  
Shui Yuan Yang ◽  
Yun Neng Wang ◽  
Cui Ping Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Grain Refinement ◽  
Microstructure And Mechanical Properties

The effects of trace boron on microstructure and mechanical properties of β type Ti-9V-3Al-3Cr-3Zr-3.5Mo (wt. %) alloy have been investigated in this study. Upon the addition of 0.02 wt. % boron, the grain size of the B-modified alloy was almost four times smaller than that of the B-free alloy. Accordingly, the tensile strength and elongation of B-modified alloy increased from 712 MPa and 14.6 % to 813 MPa and 17.9 %, respectively, mainly due to the effect of grain refinement.

scholarly journals Effects of Excessive Zr Content and Ultrasonic Treatment on Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 632
Author(s):  
Cheng Li ◽  
Shusen Wu ◽  
Shulin Lü ◽  
Jianyu Li ◽  
Longfei Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Ultrasonic Vibration ◽  
Ultrasonic Treatment ◽  
Second Phase ◽  
Cu Alloy ◽  
Cu Alloys ◽  
Microstructure And Mechanical Properties ◽  
Second Phase Particles ◽  
Properties Of Materials

The Zr element is one of the important grain refiners for 7xxx series Al-Zn-Mg-Cu alloys, but the effect of Zr content more than 0.15 wt.% needs to be deeply investigated under the action of ultrasonic vibration. In this study, the effects of Zr contents (0.1 to 0.25 wt.%) on microstructure and mechanical properties of Al-Zn-Mg-Cu alloy were studied. The results showed that Zr element could refine grains, but when the Zr content was greater than 0.15 wt.%, the grain size was not uniform, the number of second phase particles increased, and the segregation of components became more serious. It was found that after ultrasonic treatment, the grain-size inhomogeneity was greatly improved, and the Zr content could be added up to 0.2 wt.%. When the Zr content is equal or lower than 0.2 wt.%, ultrasonic treatment can effectively improve the mechanical properties of materials by refining grains and weakening segregation. However, when the Zr content is up to 0.25 wt.%, the effect is getting worse.

scholarly journals The Comparison in the Microstructure and Mechanical Properties between AZ91 Alloy and Nano-SiCp/AZ91 Composite Processed by Multi-Pass Forging Under Varying Passes and Temperatures

Materials ◽  
2019 ◽  
Vol 12 (4) ◽  
pp. 625 ◽  
Author(s):  
K.B. Nie ◽  
J.G. Han ◽  
K.K. Deng ◽  
X.J. Wang ◽  
C. Xu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Strength ◽  
Grain Refinement ◽  
Texture Evolution ◽  
Az91 Alloy ◽  
Strengthening Effect ◽  
Sic Nanoparticles ◽  
Microstructure And Mechanical Properties ◽  
Second Phases

In this study, both AZ91 alloy and nano-SiCp/AZ91 composite were subjected to multi-pass forging under varying passes and temperatures. The microstructure and mechanical properties of the alloy were compared with its composite. After six passes of multi-pass forging at a constant temperature of 400 ℃, complete recrystallization occurred in both the AZ91 alloy and composite. The decrease of temperature and the increase of passes for the multi-pass forging led to further refinement of dynamic recrystallized grains and dynamic precipitation of second phases. The grain size of the nano-SiCp/AZ91 composite was smaller than that of the AZ91 alloy under the same multi-pass forging condition, which indicated that the addition of SiC nanoparticles were beneficial to grain refinement by pinning the grain boundaries. The texture intensity for the 12 passes of multi-pass forging with varying temperatures was increased compared with that after nine passes. The ultimate tensile strength is slightly decreased while the yield strength was increased unobviously for the AZ91 alloy with the decrease of temperature and the increase of the passes for the multi-pass forging. Under the same condition of multi-pass forging, the yield strength of the composite was higher than that of the AZ91 alloy due to the Orowan strengthening effect and grain refinement strengthening resulting from externally applied SiC nanoparticles and internally precipitated second phases. By comparing the microstructure and mechanical properties between the AZ91 alloy and nano-SiCp/AZ91 composite, the strength-toughness properties of the composites at room temperature were affected by the matrix grain size, texture evolution, SiC nanoparticles distribution and the precipitated second phases.

scholarly journals Microstructure and Mechanical Properties of Magnesium Matrix Composites Interpenetrated by Different Reinforcement

2018 ◽  
Vol 8 (11) ◽  
pp. 2012 ◽  
Author(s):  
Shuxu Wu ◽  
Shouren Wang ◽  
Daosheng Wen ◽  
Gaoqi Wang ◽  
Yong Wang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Stainless Steel ◽  
Metal Matrix Composites ◽  
Grain Refinement ◽  
Metal Matrix ◽  
Matrix Composites ◽  
Magnesium Matrix ◽  
Magnesium Matrix Composites ◽  
Microstructure And Mechanical Properties

The present work discusses the microstructure and mechanical properties of the as-cast and as-extruded metal matrix composites interpenetrated by stainless steel (Fe–18Cr–9Ni), titanium alloy (Ti–6Al–4V), and aluminum alloy (Al–5Mg–3Zn) three-dimensional network reinforcement materials. The results show that the different reinforcement materials have different degrees of improvement on the microstructures and mechanical properties of the magnesium matrix composites. Among them, magnesium matrix composites interpenetrated by stainless steel reinforcement have maximum tensile strength, yield strength, and elongation, which are 355 MPa, 241 MPa, and 13%, respectively. Compared with the matrix, it increases by 47.9%, 60.7% and 85.7%, respectively. Moreover, compared with the as-cast state, the as-extruded sample has a relatively small grain size and a uniform size distribution. The grain size of the as-cast magnesium matrix composites is mainly concentrated at 200–300 μm, whereas the extruded state is mainly concentrated at 10–30 μm. The reason is that the coordination deformation of reinforcement and matrix, and the occurrence of dynamic recrystallization, cause grain refinement of magnesium matrix composite during the extrusion process, thereby improving its mechanical properties. Moreover, the improvement is attributed to the effect of the reinforcement itself, and the degree of grain refinement of the metal matrix composites.

Preparation and Characterization of As-Cast and As-Extruded Mg-1Mn-0.6Ce-3Y Alloy

2016 ◽  
Vol 849 ◽  
pp. 203-208 ◽  
Author(s):  
Gui Hua Su ◽  
Xue Ran Liu ◽  
Zhan Yi Cao
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Extrusion Ratio ◽  
Casting Method ◽  
Cast Sample ◽  
Cast Ingot ◽  
Average Grain Size ◽  
Mould Casting

Mg-1Mn-0.6Ce-3Y alloy was prepared by metal mould casting method. The as-cast ingot was homogenized and then hot-extruded by an extrusion ratio of 16:1 at 380 °C. Microstructure and mechanical properties of the as-cast and hot-extruded samples were investigated. The results showed that the as-cast sample mainly consisted of α-Mg, Mg12Ce, and Mg24Y5 phases. The average grain size of the sample homogenized at 380 °C was about 100μm, and it was greatly refined to about 6μm by dynamic recrystallization for the hot-extruded sample. The ultimate tensile strength, 0.2% yield strength and elongation of the hot-extruded sample were 244 MPa, 178 MPa and 37.5%, respectively. They were enhanced by 82%, 197% and 400%, correspondingly compared with those of the as-cast sample. The improvement of the strengths was attributed to the grain refinement, breakup of the precipitates and increase of the dislocation density.

Sign in / Sign up

Export Citation Format

Share Document