Coupling Analysis of Fluid Film and Thermal Deformation of Sealing Members in Spiral Groove Mechanical Seal

2007 ◽  
Vol 353-358 ◽  
pp. 2455-2458
Author(s):  
Jian Feng Zhou ◽  
Bo Qin Gu
Keyword(s):  
Thermal Deformation ◽  
Critical Speed ◽  
Fluid Film ◽  
Hydrodynamic Effect ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
Spiral Groove ◽  
Coupling Analysis ◽  
Rotating Speed ◽  
Bearing Force

The thermo-hydrodynamic effect in the spiral groove mechanical seal was investigated. The coupling analysis of the fluid film and the thermal deformation of sealing rings was carried out, the separation angle obtained, and the shape of the gap between the two deformed end faces determined. The results indicate that the increase of the temperature of the fluid film and the thermal deformation of the sealing rings cause the increase of the leakage rate. There exists a critical rotating speed, when the rotating speed is lower than the critical speed, the bearing force increases with the increase of the rotating speed, and once the rotating speed is higher than the critical speed, the bearing force decreases reversely. The thermal deformation weakens the hydrodynamic effect of the spiral groove mechanical seals.

Optimum Design of Flat End Face Mechanical Seal Based on Coupling Analysis

2010 ◽  
Vol 37-38 ◽  
pp. 819-822 ◽  
Author(s):  
Jian Feng Zhou ◽  
Bo Qin Gu ◽  
Chun Lei Shao
Keyword(s):  
Optimum Design ◽  
Thermal Deformation ◽  
Coupling Effect ◽  
Design Method ◽  
Fluid Film ◽  
Outer Side ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
Friction Heat ◽  
Bearing Force

The flat end face mechanical seals are widely used in shaft sealing at moderate rotational speed. The thermal deformation of the rotating and stationary rings initiated by friction heat of fluid film should be primarily considered in the design of mechanical seal. In consideration of the coupling effect among the thermal deformation of sealing rings, the fluid flow in the gap composed by end faces of sealing rings and the heat transfer from fluid film to sealing rings, the optimum design method for flat end face mechanical seal is established. The end faces are fabricated to form a divergent gap at the inner side of the sealing rings, and a convergent gap will occur at the outer side and a parallel gap will be obtained at where the original divergent gap is due to the thermal deformation. After optimization, the leakage rate can be reduced while the bearing force of fluid film is still large enough to keep the fluid lubrication of the end faces.

scholarly journals Research on the Dynamic Characteristics of Mechanical Seal under Different Extrusion Fault Degrees

Processes ◽  
2020 ◽  
Vol 8 (9) ◽  
pp. 1057
Author(s):  
Yin Luo ◽  
Yakun Fan ◽  
Yuejiang Han ◽  
Weqi Zhang ◽  
Emmanuel Acheaw
Keyword(s):  
Film Thickness ◽  
Dynamic Characteristics ◽  
Fluid Film ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
Rotating Speed ◽  
Analysis Process ◽  
Fluid Film Thickness ◽  
Object Of Study ◽  
Fault Mechanism

In order to explore the dynamic characteristics of the mechanical seal under different fault degrees, this paper selected the upstream pumping mechanical seal as the object of study. The research established the rotating ring-fluid film-stationary ring 3D model, which was built to analyze the fault mechanism. To study extrusion fault mechanism and characteristics, different dynamic parameters were used in the analysis process. Theoretical analysis, numerical simulation, and comparison were conducted to study the relationship between the fault degree and dynamic characteristics. It is the first time to research the dynamic characteristics of mechanical seals in the specific extrusion fault. This paper proved feasibility and effectiveness of the new analysis method. The fluid film thickness and dynamic characteristics could reflect the degree of the extrusion fault. Results show that the fluid film pressure fluctuation tends to be more intensive under the serious extrusion fault condition. The extrusion fault is more likely to occur when the fluid film thickness is too large or too small. Results illustrate the opening force is affected with the fluid film lubrication status and seal extrusion fault degrees. The fluid film stiffness would not always increase with the rotating speed growth. The seal fault would occur with the increasing of rotating speeds, and the leakage growth fluctuations could reflect the fault degree.

Analysis of Carrying Capacity and Friction Torque of Friction Pair Fluid-Film for High Parameter Bellows Mechanical Seal

2013 ◽  
Vol 455 ◽  
pp. 207-211
Author(s):  
Mutellip Ahmat ◽  
Zhi Wei Niu ◽  
Guzaiayi Abudoumijiti
Keyword(s):  
Carrying Capacity ◽  
High Speed ◽  
Influence Factor ◽  
Friction Pair ◽  
Scientific Basis ◽  
Friction Torque ◽  
Fluid Film ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
The Relationship

The friction pair for bellows mechanical seal as a friction element is one of the key components for it. In this research, by based on the computational fluid dynamics (CFD) numerical theory, using the Fluent software, corresponding model and parameters, the fluid-film between the clearance of the sealing ring friction pair for the bellows mechanical seal under such the high-temperature, high-pressure, high-speed as complex working conditions is numerically simulated, the relationship between the carrying-capacity of the fluid-film and the temperature, the viscosity of the fluid-film, the relationship between friction torque of the fluid-film and the speed, viscosity of the fluid-film, the influence factor of leakage are obtained. The researching results provide the scientific basis for the optimization designing of the high parameter bellows mechanical seals.

Numerical Simulation of Lubricant Liquid Film of the Laser Surface Textured Micro-Pore Face Mechanical Seal

2013 ◽  
Vol 579-580 ◽  
pp. 548-553
Author(s):  
Peng Gao Zhang ◽  
Bo Qin Gu ◽  
Long Wei ◽  
Qi He Liu
Keyword(s):  
Liquid Film ◽  
Influence Factors ◽  
Laser Surface ◽  
Hydrodynamic Effect ◽  
Mechanical Seal ◽  
Area Density ◽  
Rotating Speed ◽  
Sealing Performance ◽  
Flow Field Characteristics ◽  
Fluent Software

The flow field characteristics of lubricant liquid film of the laser surface textured micro-pore face mechanical seal were studied by Fluent software, and the effects of geometric parameters of micro pores and operating parameters on the sealing performance were analyzed. The results show that the hydrodynamic effect of the laser surface textured micro-pore face mechanical seal is very obvious, and micro-pores make the friction state between rotating ring and stationary ring change to fluid friction. It can also be found that the rotating speed, the medium pressure, the area density and the liquid film thickness have effect on the sealing performance, among these influence factors, the area density has the greatest effect on the sealing performance, and it should be 0.2-0.3.

Analysis of Mechanical Seal Behavior During Transient Operation

1998 ◽  
Vol 120 (2) ◽  
pp. 191-197 ◽  
Author(s):  
S. R. Harp ◽  
R. F. Salant
Keyword(s):  
Thermal Deformation ◽  
Transient Behavior ◽  
Mechanical Deformation ◽  
Contact Forces ◽  
Squeeze Film ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
Pressure Distributions ◽  
Deformation Mechanics ◽  
Gas Seals

A mathematical model that predicts the transient behavior of gas or liquid lubricated hydrostatic mechanical seals has been developed. The analysis includes an evaluation of the fluid, contact, and deformation mechanics of a mechanical seal subject to constant or varying rotational speed and sealed pressure. Squeeze film effects are included. For gas seals, slip at the walls is also taken into account. Results include predictions of film thickness distributions, contact forces, leakage rates, pressure distributions, heat generation rates, thermal deformation, and mechanical deformation.

Relationship Between Vibrations and Mechanical Seal Failures in Centrifugal Pumps

2005 ◽  
Author(s):  
David B. Stefanko ◽  
Robert A. Leishear
Keyword(s):  
Industrial Applications ◽  
The Other ◽  
Fluid Film ◽  
Operating Speed ◽  
Mechanical Seal ◽  
Mechanical Seals ◽  
Centrifugal Pumps ◽  
Radial Vibrations ◽  
The Common ◽  
Bearing Design

A reduction of radial vibrations in mechanical seals increases the life of the seals in centrifugal pumps. Mechanical seals consist of two smooth seal faces. One face is stationary with respect to the pump. The other rotates. Between the faces a fluid film evaporates as the fluid moves radially. Ideally, the film evaporates as it reaches the outer surface of the seal faces, thereby preventing leakage from the pump and effectively lubricating the two surfaces. Relative vibrations between the two surfaces affect the fluid film, damage the faces, and decrease the life of the seals. In a series of industrial applications, different techniques were used to minimize vibration, and the life of the seals was shown to significantly increase. The operating speed was controlled in one case, the bearing design was replaced in another case, and the stiffness of the pump was altered in still another case. The common corrective action in each case was a reduction in vibration.

Predictions for Non-Contacting Mechanical Face Seal Vibration With External Excitation From Pump Vibration: Part II — Flexibly Mounted Rotor

2018 ◽  
Author(s):  
Clay S. Norrbin ◽  
Dara W. Childs
Keyword(s):  
Excitation Frequency ◽  
Harmonic Excitation ◽  
Fluid Film ◽  
Axial Distance ◽  
Mechanical Seal ◽  
Seal Ring ◽  
Mechanical Seals ◽  
Running Speed ◽  
Frequency Dependent ◽  
Frequency Independent

Stability and response predictions are presented for a Flexibly Mounted Rotor (FMR) mechanical seal ring using the model developed by Childs in 2018. The seal ring is excited by lateral/pitch vibration from the rotor/housing. The model includes a frequency dependent stiffness and damping model for the O-ring and a frequency independent model for the fluid film. The dynamic coefficients are speed and frequency dependent. The mechanical seal is modeled after a typical FMR mechanical seal. Parameters for radius, fluid film clearance, and O-Ring axial distances are varied. The axial distance between the O-Ring and seal ring inertia center doz is found to couple lateral rotor motion and seal ring pitch vibration. The predictions show a dependency on both excitation frequency and running speed. The analyzed FMR has a critical region with high transmissibility in a region around a speed and excitation frequency of 70 kRPM. Another region of high transmissibility is predicted to be with sub-harmonic excitation frequency. The FMR seal ring also has an unstable region that is sub-harmonic of 1% running speed. Running back on the HQ curve for a pump causes broadband sub-harmonic excitaiton, which can cause rub failures for FMR mechanical seals.

On hydrodynamic lubrication characteristics of ferrofluid film in a spiral groove mechanical seal

2018 ◽  
Vol 70 (9) ◽  
pp. 1783-1797 ◽  
Author(s):  
Penggao Zhang ◽  
Boqin Gu ◽  
Jianfeng Zhou ◽  
Long Wei
Keyword(s):  
Electromagnetic Field ◽  
Volume Fraction ◽  
Hydrodynamic Lubrication ◽  
Groove Width ◽  
Mechanical Seal ◽  
Spiral Groove ◽  
Content Type ◽  
Rotating Speed ◽  
Lubrication Characteristics ◽  
Spiral Angle

Purpose The purpose of this study is to investigate the hydrodynamic lubrication characteristics of ferrofluid film for spiral groove mechanical seal in external electromagnetic field and to analyze the effects of the volume fraction of ferrofluid, parameters of the electromagnetic field, operating parameters and geometrical parameters of mechanical seal on the characteristics of ferrofluid film. Design/methodology/approach The relationship between the ferrofluid viscosity and the intensity of external electromagnetic field was established. Based on the Muijderman narrow groove theory, the pressure distribution was calculated with the trial method by trapezoid formula. Findings It was found that pressure, average viscosity, average density and opening force of ferrofluid between end faces increase with the increase in intensity of current, volume fraction of ferrofluid, rotating speed, pressure differential and spiral angle; decrease with the increase in temperature; and increase at first and then decrease with the increase in the ratio of groove width to weir and the groove length. All of them reach the maximum value when the ratio of width of groove to weir is 0.7 and the ratio of groove length is 0.6. Leakage of ferrofluid increases with an increase in intensity of current, volume fraction of ferrofluid, rotating speed, pressure differential, spiral angle and ratio of groove length; decreases with an increase in temperature; and increases at first and then decreases with the increase in the ratio of groove width to weir. The tendencies of characteristics of silicone oil are consistent with those of ferrofluid, and the characteristics of silicone oil are smaller than those of ferrofluid under the same condition. Originality/value The volume fraction of ferrofluid, rotating speed, spiral angle, ratio of groove width to weir, groove length and temperature have a significant influence on the characteristics of ferrofluid film; however, intensity of current and the pressure differential have slight influence on the characteristics of ferrofluid film. An analytical method for analyzing hydrodynamic lubrication characteristics of ferrofluid film in a spiral groove mechanical seal was proposed based on the Muijderman narrow groove theory.

Sign in / Sign up

Export Citation Format

Share Document