Synthesis and Characterization of MgPSZ-PMMA Composite by Sol-Gel Modification and Direct Foaming Technique Using Egg Whites

2016 ◽  
Vol 720 ◽  
pp. 290-295
Author(s):  
Veni Takarini ◽  
Alfend Rudyawan ◽  
Andri Hardiansyah ◽  
Rifki Septawendar ◽  
Niki Prastomo ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Crystal Size ◽  
Sol Gel ◽  
Porous Structures ◽  
X Ray Diffraction ◽  
X Ray ◽  
Direct Foaming ◽  
Transmission Electron ◽  
Direct Foaming Method

This study prepared Magnesium-Partially Stabilized Zirconia (Mg-PSZ) filler synthesis and direct foaming technique using egg whites, and impregnated by PMMA. The results were evaluated systematically by X-ray diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Electron Microscope (TEM). XRD results denote that the powder sample of MgPSZ was successfully formed with various crystal size of tetragonal and monoclinic phase. SEM and TEM observations revealed that nanoparticles MgPSZ were in spherical and long rounded shapes. Furthermore, SEM observation revealed that the direct foaming method were also successful in the formation of porous structures which favourable for impregnation process by PMMA. The use of egg whites as a polymer precursor in both methods demonstrates that porous specimens contained nanosized, predominantly tetragonal, Mg-PSZ powders were successfully synthesized. This shall yield an interesting prospect towards cheap, reliable, and biocompatible product to resemble the modulus elasticity of dentin.

scholarly journals Fabrikasi Nanotubes Titanium Dioksida (TiO2) Menggunakan Metode Hidrotermal

2017 ◽  
Vol 3 (1) ◽  
pp. 20-26
Author(s):  
Atik Setyani ◽  
Emas Agus Prastyo Wibowo
Keyword(s):  
Tio2 Nanoparticles ◽  
Tio2 Nanotubes ◽  
Crystal Size ◽  
High Surface ◽  
Sol Gel ◽  
High Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron

Nanotubes received great attention because it has a high surface area. In this study, TiO2 nanotubes fabricated via hydrothermal method from  synthesis of TiO2 nanoparticles via sol-gel method. Catalysts that have been synthesized later in the characterization by X-Ray Diffraction (XRD) to obtain the crystal size and crystallinity. Crystal size of TiO2 nanoparticles at a temperature of 450C is 13.78 nm. Then characterized by Transmission Electron Microscopy (TEM) to look at the formation of nanotubes. Characterization of TiO2 nanotubes with TEM shows that the structure of the tubes had already been formed TNTs although the growth has not been perfect. It can be seen from the structure TNTs who tend to be short and yet so irregular.DOI: http://dx.doi.org/10.15408/jkv.v0i0.5036  

scholarly journals Fabrication and characterization of ferrites (Mg and Mn) based on FTIR, XRD, SEM and TEM

2014 ◽  
Vol 8 (3) ◽  
Author(s):  
Tang Ing Hua ◽  
Rita Sundari
Keyword(s):  
Electron Microscope ◽  
Volume Expansion ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Semiconducting Materials ◽  
Thermal Agitation ◽  
X Ray ◽  
Transmission Electron ◽  
Fabrication And Characterization

This study has encountered with the fabrication of ferrites (Mg and Mn) using citric acid as anionic surfactant in sol-gel method followed by calcinations at varied temperatures (300, 600, 800°C) for 2h, respectively. The fabricated ferrites have been characterized by FTIR (Fourier Transform Infrared Spectroscopy), XRD (X-Ray Diffraction), SEM (Scanning Electron Microscope) and TEM (Transmission Electron Microscope). The FTIR spectrum for MnFeO3 shows that some functional groups already removed under 300°C calcination due to several oxidation numbers possessed by Mn leading to more flexibility. The XRD diffractograms for both MgFe2O4 and MnFeO3 show that the transition phase from amorphous to crystalline structure occurred in the temperature range of 300-600°C. The SEM mappings based on the Fe distribution for both MgFe2O4 and MnFeO3 show that more Fe distributed over the ferrites surface at 600 and 800°C, while the SEM mappings for both ferrites (Mg and Mn) show less Fe distribution at 300°C calcination, thus, it indicates more repulsion force bearing by higher amounts of Fe atoms at higher thermal agitation due to volume expansion. The TEM spectra proved that both ferrites existed as crystals after calcined at 600°C. The fabricated ferrites have remarkable electrical properties useful for the manufacture of semiconducting materials.

scholarly journals Effect of Preheating Temperature on Synthesis of Pure BiFeO3 via Sol–Gel Method

Nanopages ◽  
2019 ◽  
pp. 1-11
Author(s):  
G. M. Taha ◽  
M. N. Rashed ◽  
M. S. El-Sadek ◽  
M. A. Moghazy
Keyword(s):  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Pure Bifeo3 ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Transmission Electron ◽  
Preheating Temperature

Abstract BiFeO3 (BFO) nanopowder was synthesized in a pure form via a sol- gel method based on glycol gel reaction. Effect of drying and preheating temperature on preventing other phases was studied. Many parameters were studied as calcination temperature and time & stirring temperature as well. The prepared powder was characterized by X-Ray Diffraction of powder (XRD) and Transmission Electron Microscope (TEM). High pure BiFeO3 was obtained by preheated process at 400 °C for 0.5 h and calcination at 600 °C for 0.5 h without any impurities compared to dry at110 °C.

Sol-Gel Synthesis and Characterization of Nanocrystalline Bi4Ti3O12 Powders

2014 ◽  
Vol 997 ◽  
pp. 359-362 ◽  
Author(s):  
Chun Hong Ma ◽  
Xue Lin ◽  
Liang Wang ◽  
Yong Sheng Yan
Keyword(s):  
Phase Inversion ◽  
Bismuth Titanate ◽  
Sol Gel ◽  
Tetrabutyl Titanate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Sol Gel Synthesis ◽  
Source Materials

Nanocrystalline bismuth titanate (Bi4Ti3O12; BTO) powders were successfully prepared by the sol-gel method, using bismuth nitrate (Bi(NO3)3·5H2O) and tetrabutyl titanate (Ti(OC4H9)4) as source materials, acetic anhydride and ethanediol as solvents. The thermal decomposition and phase inversion process of the gel precursors were studied by using differential thermal analysis (DTA). The crystal structures and microstructures of BTO powders were investigated by using x-ray diffraction (XRD), and transmission electron microscope (TEM). The crystallization of amorphous bismuth titanate has been discussed. The effect of sintering temperature on the structure and morphology of BTO was investigated. At 644 oC and above, BTO powder undergoes a phase transformation from tetragonal to orthorhombic. At 900 oC, the purified orthorhombic BTO nanocrystals were obtained.

Sol-gel derived Ba(Mg1/3Ta2/3)O3 thin films: Preparation and structure

1997 ◽  
Vol 12 (3) ◽  
pp. 596-599 ◽  
Author(s):  
Ji Zhou ◽  
Qing-Xin Su ◽  
K. M. Moulding ◽  
D. J. Barber
Keyword(s):  
Thin Films ◽  
Annealing Temperature ◽  
Volume Fraction ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Small Grains

Ba(Mg1/3Ta2/3)O3 thin films were prepared by a sol-gel process involving the reaction of barium isopropoxide, tantalum ethoxide, and magnesium acetate in 2-methoxyethanol and subsequently hydrolysis, spin-coating, and heat treatment. Transmission electron microscopy, x-ray diffraction, and Raman spectroscopy were used for the characterization of the thin films. It was shown that the thin films tend to crystallize with small grains sized below 100 nm. Crystalline phase with cubic (disordered) perovskite structure was formed in the samples annealed at a very low temperature (below 500 °C), and well-crystallized thin films were obtained at 700 °C. Although disordered perovskite is dominant in the thin films annealed below 1000 °C, a low volume fraction of 1 : 2 ordering domains was found in the samples and grows with an increase of annealing temperature.

Microstructural Characterization of a Fe-Based Compostie Reinforced by TiC

2011 ◽  
Vol 675-677 ◽  
pp. 835-838
Author(s):  
Jing Wang ◽  
Si Jing Fu ◽  
Hong Cheng
Keyword(s):  
Electron Microscope ◽  
Microstructural Characterization ◽  
Interfacial Structure ◽  
Synthesis Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Tic Particle ◽  
Scanning Electron

The present work reported the preparation of TiC/Fe-based composite by the synthesis reaction from Ti, C and Fe. The sintered composites were characterized by X-ray diffraction, scanning electron microscope and transmission electron microscope. TiC, Fe3C and α-Fe were detected by X-ray diffraction analysis. The scanning and transmission electron micrographs revealed the morphology and distribution of the reinforcements, the microstructure of Fe matrix, the interfacial structure of TiC particle-to-Fe matrix. Moreover, the formation reason of the voids in composite was also discussed.

scholarly journals Characterization of Fe Doped AC/TiO2

2019 ◽  
Vol 8 (12S) ◽  
pp. 1146-1147
Keyword(s):  
Activated Carbon ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Anatase Phase ◽  
Sol Gel ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Abstract: The photocatalytic composite Fe doped AC/TiO2 has been prepared by sol-gel method. The prepared Fe doped AC/TiO2 composite were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD).The SEM analysis showed that Fe and TiO2 were attached to the Activated Carbon surfaces. The X-Ray Diffraction data showed that Fe doped AC/TiO2 composite mostly contained anatase phase.

Fabrication, Structural Characterization and Formation Mechanism of Multiferroic BiFeO3 Nanotubes

2008 ◽  
Vol 8 (1) ◽  
pp. 335-339 ◽  
Author(s):  
Satyendra Singh ◽  
S. B. Krupanidhi
Keyword(s):  
Electron Microscope ◽  
Formation Mechanism ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Multiferroic Bifeo ◽  
High Resolution Tem ◽  
Perovskite Crystal

Multiferroic BiFeO3 (BFO) nanotubes have been successfully fabricated by the modified sol–gel method within the nanochannels of porous anodic aluminum oxide (AAO) templates. The morphology, structure and composition of the nanotubes were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), selected-area electron diffraction (SAED), high resolution TEM, (HRTEM) and energy-dispersive X-ray spectroscopy (EDX). Postannealed (650 °C for 1 h), BFO nanotubes were polycrystalline and X-ray diffraction study revealed that they are of the rhomohedrally distorted perovskite crystal structure. The results of SEM and TEM revealed that BFO nanotubes possessed a uniform length (up to 60 μm) and diameter (about 200 nm), which were controlled by the thickness and the pore diameter of the applied AAO template, respectively and the thickness of the wall of the BFO nanotube was about 15 nm. Y-junctions in the BFO nanotubes were observed. EDX analysis demonstrated that stoichiometric BiFeO3 was formed. HRTEM analysis confirmed that the obtained BFO nanotubes made up of nanoparticles (3–6 nm). The possible formation mechanism of BFO nanotubes was discussed.

Synthesis and Characterization of Lamellar Nanostructured Yttrium Films Using Lyotropic Liquid Crystalline Templates

2011 ◽  
Vol 399-401 ◽  
pp. 1915-1918
Author(s):  
Rui Jie Guo ◽  
Xiao Juan Sha ◽  
Lei Lei Cao
Keyword(s):  
Electron Microscope ◽  
Liquid Crystalline ◽  
Electroless Deposition ◽  
Electronic Materials ◽  
X Ray Diffraction ◽  
Regular Array ◽  
X Ray ◽  
Surface Areas ◽  
Transmission Electron

The lamellar nanostructured yttrium films on α-Al2O3 substrates were successfully synthesized by electroless deposition using the lyotropic liquid crystalline templating strategy. The reaction of hydrazine hydrate and Y3+ dissolved within the aqueous domains of the lyotropic liquid crystalline phase produced the nanostructured yttrium films. The low-angle X-ray diffraction (XRD), transmission electron microscope (TEM) and scanning electron microscope (SEM) indicated that the as-resulted films possessed lamellar regular array of nanochannels with periodicity of 6 nm. With well-defined nanochannels and higher surface areas, the nanostructured films may find applications in the field of electronic materials.

Investigation on Nano-Sized ZnO Powder Doped with Al3+ Prepared by Sol-Gel Method

2012 ◽  
Vol 621 ◽  
pp. 3-7
Author(s):  
Yu Xiong ◽  
Ji Zheng ◽  
Song Lin Li ◽  
Xue Jia Liu ◽  
Lu Liang
Keyword(s):  
Electron Microscope ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Transmission Electron ◽  
Sol Gel Process ◽  
Doped Zno ◽  
Zno Powder ◽  
Tin Tetrachloride

Al3+-doped ZnO nano-powder was prepared by sol-gel process, using tin tetrachloride and titanium tetrachloride as starting materials. The crystallinity and purity of the powder were analyzed by X-ray diffraction spectrometer (XRD). And the size and distribution of Al3+-doped ZnO grains were studied using transmission electron microscope (TEM) and scanning electron microscope (SEM). The results showed that the Al3+ was successfully doped into the crystal lattice of tin oxide and that the electric conductivity of Al3+-doped ZnO sample was improved significantly.

Sign in / Sign up

Export Citation Format

Share Document