A New Frontier in Microalloying: Advanced High Strength, Coated Sheet Steels

2005 ◽  
Vol 500-501 ◽  
pp. 27-38 ◽  
Author(s):  
Anthony J. DeArdo ◽  
J.E. Garcia ◽  
Ming Jian Hua ◽  
C. Isaac Garcia
Keyword(s):  
High Strength ◽  
Laboratory Simulation ◽  
Sheet Steels ◽  
Trip Steels ◽  
New Frontier ◽  
Evolution Of Microstructure ◽  
Coated Sheet

TRIP steels containing Mn, Si, Al, Mo, and Nb have been examined using a laboratory simulation of a continuous hot dipped galvanizing line. The evolution of microstructure has been studied as the steel passes through the various stages of CG line processing. Tensile strengths approaching 800 MPa and ductilities approaching 30% have been achieved in the 1.5Mn-0.5Si- 1.0Al-0.015Mo-0.03Nb system.

scholarly journals Precipitation Behavior of AlN Inclusions in Fe-0.5Al-2.0Mn Alloy Under Continuous Unidirectional Solidification Process

2021 ◽  
Vol 8 ◽  
Author(s):  
Nghiem NguyenVan ◽  
Kengo Kato ◽  
Hideki Ono
Keyword(s):  
Solidification Process ◽  
High Strength ◽  
Unidirectional Solidification ◽  
Chemical Compositions ◽  
Precipitation Behavior ◽  
Sheet Steels ◽  
Trip Steels ◽  
Initial Content ◽  
The Stability ◽  
New Generation

Medium Manganese Transformation Induced Plastic (Mn-TRIP) steels are expected to be a new generation of advanced high strength sheet steels due to their excellent balance between material cost and mechanical properties. During the solidification process, AlN precipitates at the grain boundary, which leads to the serious deterioration of hot ductility. However, the precipitation of AlN in Mn-TRIP steel has not been clear. In this study, the chemical compositions, morphology, size distribution, and the precipitation behavior of AlN inclusion in an Fe-0.5Al-2.0Mn alloy were studied under the continuous unidirectional solidification process. The results show that there are two types of nitride inclusions in the Fe-0.5Al-2.0Mn alloy: AlN inclusion and complex inclusion of Al2O3-AlN. The planar sections of most AlN particles are hexagonal. Based on the thermodynamic calculation, it was found that the content of Al has a large effect on the stability of Al2O3 and AlN. When the content of Al increases, the molten iron can be changed from saturated by Al2O3 to saturated by AlN. During the solidification process, the precipitation of Al2O3 inclusions occurred at the beginning of the solidification process. The precipitation of AlN inclusions occurred when the contents of Al and N exceeded the equilibrium value and grew until the end of the solidification. The precipitation conditions of AlN inclusion in the Fe-0.5Al-2.0Mn alloy during the solidification process were discussed. The precipitation and the amount of precipitate of AlN inclusions depend on the initial contents of Al, N, and O. It was found that the precipitation of AlN inclusions can be controlled by reducing the initial content of N to less than 0.0072 mass%.

scholarly journals Microstructural effects on fracture toughness of ultra-high strength dual phase sheet steels

2021 ◽  
Vol 802 ◽  
pp. 140631
Author(s):  
D. Frómeta ◽  
N. Cuadrado ◽  
J. Rehrl ◽  
C. Suppan ◽  
T. Dieudonné ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
High Strength ◽  
Dual Phase ◽  
Sheet Steels ◽  
Microstructural Effects

Fundamental Study on Improvement in Frontal Crashworthiness by Application of High-Strength Sheet Steels

1997 ◽  
Author(s):  
Naomitsu Mizui ◽  
Kiyoyuki Fukui ◽  
Nobusato Kojima ◽  
Miyuki Yamamoto ◽  
Yoshiaki Kawaguchi ◽  
...  
Keyword(s):  
High Strength ◽  
Fundamental Study ◽  
Sheet Steels

scholarly journals Warm Formability of Ultra High-Strength Low Alloy TRIP-aided Sheet Steels with Bainitic Ferrite Matrix

2005 ◽  
Vol 91 (2) ◽  
pp. 278-284 ◽  
Author(s):  
Koh-ichi SUGIMOTO ◽  
Sung-Moo SONG ◽  
Jyunya SAKAGUCHI ◽  
Akihiko NAGASAKA ◽  
Takahiro KASHIMA
Keyword(s):  
Bainitic Ferrite ◽  
High Strength ◽  
Ferrite Matrix ◽  
Sheet Steels

Influence of the Processing Variables on the Microstructure Evolution of a Bainitic Carbide-Free Steel

2016 ◽  
Vol 879 ◽  
pp. 867-872 ◽  
Author(s):  
M.C. Taboada ◽  
I. Gutiérrez ◽  
D. Jorge-Badiola ◽  
S.M.C. van Bohemen ◽  
F. Hisker ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
High Volume ◽  
X Ray Diffraction ◽  
Tempered Martensite ◽  
Trip Steels ◽  
Volume Fractions ◽  
Advanced High Strength Steels ◽  
Processing Variables

New trends focused on achieving higher performance steels has led to a so-called 3rd Generation Advanced High Strength Steels (AHSS), in which the typical polygonal ferrite found in TRIP steels as a matrix phase is replaced by harder phases as Carbide-Free Bainite (CFB) and/or (tempered) martensite. Besides, large volume fractions of retained austenite (R.A.) with adequate stability are aimed for to improve the formability of the steels. Si containing steels are regarded as the most suitable to retard cementite formation and consequently reach high volume fractions of RA. In this work, CFB annealing schedules were applied to dilatometer samples of Fe-0.22C-2.0Mn-1.3Si. The overaging temperature TB was varied between 390 oC and 480 oC, and other processing variables investigated were the austenitizing temperature Taus, and the overaging holding time tB. The annealed samples analyzed with LOM, FEG-SEM, EBSD and X-ray diffraction techniques show that markedly different complex microstructures made up of bainite, ferrite, MA phase and retained austenite (R.A) are accomplished depending on the specific thermal cycle. These results are described in detail and discussed in relation to the dilatometry measurements.

scholarly journals Design of an Effective Heat Treatment Involving Intercritical Hardening for High Strength/High Elongation of 0.2C–3Al–(6–8.5)Mn–Fe TRIP Steels: Microstructural Evolution and Deformation Behavior

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1275 ◽  
Author(s):  
Yanjie Mou ◽  
Zhichao Li ◽  
Xiaoteng Zhang ◽  
Devesh Misra ◽  
Lianfang He ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Stress Relaxation ◽  
Deformation Behavior ◽  
High Strength ◽  
Total Elongation ◽  
Trip Effect ◽  
High Ductility ◽  
Trip Steels ◽  
Effective Heat ◽  
High Elongation

High strength/high elongation continues to be the primary challenge and focus for medium-Mn steels. It is elucidated herein via critical experimental analysis that the cumulative contribution of transformation-induced plasticity (TRIP) and microstructural constituents governs high strength/high elongation in 0.2C–3Al–(6–8.5)Mn–Fe steels. This was enabled by an effective heat treatment involving a combination of intercritical hardening and tempering to obtain high strength/high ductility. An excellent combination of high ultimate tensile strength of 935–1112 MPa and total elongation of 35–40% was obtained when the steels were subjected to intercritical hardening in the temperature range of 700–750 °C and low tempering at 200 °C. The intercritical hardening impacted the coexistence of austenite, ferrite, and martensite, such that the deformation behavior varied with the Mn content. The excellent obtained properties of the steels are attributed to the cumulative contribution of the enhanced TRIP effect of austenite and the microstructural constituents, ferrite and martensite. The discontinuous TRIP effect during deformation involved stress relaxation, which was responsible for the high ductility. Lamellar austenite, unlike the equiaxed microstructure, is envisaged to induce stress relaxation during martensitic transformation, resulting in the discontinuous TRIP effect.

scholarly journals Quantitative Description of External Force Induced Phase Transformation in Silicon–Manganese (Si–Mn) Transformation Induced Plasticity (TRIP) Steels

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3781
Author(s):  
Zhongping He ◽  
Huachu Liu ◽  
Zhenyu Zhu ◽  
Weisen Zheng ◽  
Yanlin He ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Carbon Steel ◽  
Trip Steel ◽  
Retained Austenite ◽  
Low Carbon Steel ◽  
High Strength ◽  
High Plasticity ◽  
Low Carbon ◽  
Transformation Induced Plasticity ◽  
Trip Steels

Transformation Induced Plasticity (TRIP) steels with silicon–manganese (Si–Mn) as the main element have attracted a lot of attention and great interest from steel companies due to their low price, high strength, and high plasticity. Retained austenite is of primary importance as the source of high strength and high plasticity in Si–Mn TRIP steels. In this work, the cold rolled sheets of Si–Mn low carbon steel were treated with TRIP and Dual Phase (DP) treatment respectively. Then, the microstructure and composition of the Si–Mn low carbon steel were observed and tested. The static tensile test of TRIP steel and DP steel was carried out by a CMT5305 electronic universal testing machine. The self-built true stress–strain curve model of TRIP steel was verified. The simulation results were in good agreement with the experimental results. In addition, the phase transformation energy of retained austenite and the work borne by austenite in the sample during static stretching were calculated. The work done by austenite was 14.5 J, which was negligible compared with the total work of 217.8 J. The phase transformation energy absorption of retained austenite in the sample was 9.12 J. The role of retained austenite in TRIP steel is the absorption of excess energy at the key place where the fracture will occur, thereby increasing the elongation, so that the ferrite and bainite in the TRIP steel can absorb energy for a longer time and withstand more energy.

scholarly journals Effect of Retained Austenite and Non-Metallic Inclusions on the Mechanical Properties of Resistance Spot Welding Nuggets of Low-Alloy TRIP Steels

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1064 ◽  
Author(s):  
Víctor H. Vargas Cortés ◽  
Gerardo Altamirano Guerrero ◽  
Ignacio Mejía Granados ◽  
Víctor H. Baltazar Hernández ◽  
Cuauhtémoc Maldonado Zepeda
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Retained Austenite ◽  
High Strength ◽  
Microstructural Characterization ◽  
Spot Welds ◽  
Trip Steels ◽  
Resistance Spot ◽  
Lap Shear ◽  
Metallic Inclusions

The combination of high strength and formability of transformation induced plasticity (TRIP) steels is interesting for the automotive industry. However, the poor weldability limits its industrial application. This paper shows the results of six low-alloy TRIP steels with different chemical composition which were studied in order to correlate retained austenite (RA) and non-metallic inclusions (NMI) with their resistance spot welded zones to their joints’ final mechanical properties. RA volume fractions were quantified by X-ray microdiffraction (µSXRD) while the magnetic saturation technique was used to quantify NMI contents. Microstructural characterization and NMI of the base metals and spot welds were assessed using scanning electron microscopy (SEM). Weld nuggets macrostructures were identified using optical microscopy (OM). The lap-shear tensile test was used to determine the final mechanical properties of the welded joints. It was found that NMI content in the fusion zone (FZ) was higher than those in the base metal and heat affected zone (HAZ). Whereas, traces of RA were found in the HAZ of highly alloyed TRIP steels. Lap-shear tensile test results showed that mechanical properties of spot welds were affected by NMI contents, but in a major way by the decomposition of RA in the FZ and HAZ.

Sign in / Sign up

Export Citation Format

Share Document