Changes in the Mechanical Properties and Microstructure of AZ91 Cast Mg Alloy Caused by Heat Treatment

2007 ◽  
Vol 561-565 ◽  
pp. 311-314 ◽  
Author(s):  
Kaname Fujii ◽  
Tokimasa Kawabata ◽  
Kenji Matsuda ◽  
Susumu Ikeno
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Test ◽  
Mg Alloy ◽  
Composition Analysis ◽  
Test Results ◽  
Nodular Structure ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes ◽  
Alloy Cast

Changes in the mechanical properties on AZ91 Mg alloy cast into sand mold caused by heat-treatment and its microstructure were investigated by the tensile test and observation using optical and scanning electron microscopes, and chemical composition analysis. Tensile test results show that the specimens aged at 441K have larger elongation than those of aged at 489K, although they had same proof stress. The fracture surface observation reveal the cleavage fracture of aged specimen caused by the nodular structure as well as the formation of micro void around the coarse spheroidal Al-Mn-(Fe) phase.

Effect of Surface Penetrating Sealer on the Microstructure Properties of Cement-Based Composites

2013 ◽  
Vol 651 ◽  
pp. 245-250
Author(s):  
Tasi Lung Weng ◽  
Wei Ting Lin
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Concrete Durability ◽  
Test Results ◽  
Chloride Permeability ◽  
Durability Test ◽  
Chloride Resistance ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes ◽  
Effect Of Surface

The effect of penetrating sealer on the structure of surface pore, mechanical properties, and durability of cement-based composites was studied. Concrete specimens with various water/cement ratios (w/c=0.35, 0.45, 0.55) were cast and treated surfaced with various amounts of penetrating sealer at different ages. The effect of penetrating sealer on the mechanical properties of concrete was assessed by compressive strength. And, the rapid chloride permeability was also explored to test concrete durability. Test results indicate that the application of penetrating sealer significantly improves concrete compressive strength and chloride resistance. By using scanning electron microscopes observation, the penetrating depth of penetrating sealer can be determined and is about 2 cm. The penetrating sealer in this study may be categorized as deep penetrating sealer.

Effect of the Spinning Deformation Processing on Microstructure and Mechanical Properties of A356 Wheels

2016 ◽  
Vol 850 ◽  
pp. 526-531
Author(s):  
Mao Wen Liu ◽  
Wen Long Xiao ◽  
Cong Xu ◽  
Hiroshi Yamagata ◽  
Jiu Xin Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Properties ◽  
A356 Alloy ◽  
Deformation Processing ◽  
Coarse Microstructure ◽  
Deformation And Heat Treatment ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes ◽  
Porosity Percentage

The influences of spinning deformation and heat treatment on microstructure and tensile properties of A356 alloy at different cooling rates were investigated in this study by optical and scanning electron microscopes. The results indicated that spinning deformation enhanced the tensile properties of the alloy due to the reduction of Si size and porosity percentage, especially in the samples with coarse microstructure. Heat treatment increased the strength while decreased the ductility of the alloy because of the precipitation of brittle Mg2Si in Al matrix. It is suggested that the spinning deformation processing is an effective technique to produce A356 alloy wheels with high mechanical properties.

Effect of post-heat treatment on microstructure and mechanical properties of laser welded Al-Cu-Mg alloy

2021 ◽  
Vol 64 ◽  
pp. 620-632
Author(s):  
Alexander Malikov ◽  
Anatoly Orishich ◽  
Igor Vitoshkin ◽  
Evgeniy Karpov ◽  
Alexei Ancharov
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Mg Alloy ◽  
Post Heat Treatment ◽  
Microstructure And Mechanical Properties

scholarly journals Characteristics of Lightweight Cellular Concrete and Effects on Mechanical Properties

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2678 ◽  
Author(s):  
Wei Yu ◽  
Xu Liang ◽  
Frank Mi-Way Ni ◽  
Abimbola Grace Oyeyi ◽  
Susan Tighe
Keyword(s):  
Mechanical Properties ◽  
Pore Structure ◽  
High Definition ◽  
Pore Characteristics ◽  
Software Applications ◽  
Solid Part ◽  
Electron Microscopes ◽  
Lab Test ◽  
Scanning Electron Microscopes ◽  
Cellular Concrete

This study investigated the pore structure and its effects on mechanical properties of lightweight cellular concrete (LCC) in order to understand more and detailed characteristics of such structure. As part of investigation, environment scanning electron microscopes (ESEM) and industrial high-definition (HD) macro photography camera were separately used to capture and compare images of specimens. Physical properties of the pore structure, including pore area, size, perimeter, fit ellipse, and shape descriptors, were studied based on the image processing technology and software applications. Specimens with three different densities (400, 475, and 600 kg/m3) were prepared in the laboratory. Firstly, the effects of density on the characteristics of pore structure were investigated; furthermore, mechanical properties (compressive strength, modulus of elasticity and Poisson’s ratio, flexural strength and splitting tensile strength of LCC) were tested. The relationships among pore characteristics, density, and mechanical properties were analyzed. Based on the results obtained from the lab test—comparisons made between specimens with high-densities and those with low-densities—it was found significant variability in bubble size, thickness, and irregularity of pores. Furthermore, the increase of density is accompanied by better mechanical properties, and the main influencing factors are the thickness of the solid part and the shape of the bubble. The thicker of solid part and more regular pores of LCC has, the better mechanical properties are.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

scholarly journals Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4223 ◽  
Author(s):  
Xi Zhao ◽  
Shuchang Li ◽  
Fafa Yan ◽  
Zhimin Zhang ◽  
Yaojin Wu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Microstructure Evolution ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Annular Channel ◽  
Mg Alloy ◽  
Strengthening Effect ◽  
Β Phase ◽  
Angular Extrusion

Microstructure evolution and mechanical properties of AZ80 Mg alloy during annular channel angular extrusion (350 °C) and heat treatment with varying parameters were investigated, respectively. The results showed that dynamic recrystallization of Mg grains was developed and the dendritic eutectic β-Mg17Al12 phases formed during the solidification were broken into small β-phase particles after hot extrusion. Moreover, a weak texture with two dominant peaks formed owing to the significant grain refinement and the enhanced activation of pyramidal <c + a> slip at relative high temperature. The tension tests showed that both the yield strength and ultimate tensile strength of the extruded alloy were dramatically improved owing to the joint strengthening effect of fine grain and β-phase particles as compared with the homogenized sample. The solution treatment achieved the good plasticity of the alloy resulting from the dissolution of β-phases and the development of more equiaxed grains, while the direct-aging process led to poor alloy elongation as a result of residual eutectic β-phases. After solution and aging treatment, simultaneous bonding strength and plasticity of the alloy were achieved, as a consequence of dissolution of coarse eutectic β-phases and heterogeneous precipitation of a large quantity of newly formed β-phases with both the morphologies of continuous and discontinuous precipitates.

scholarly journals Identification of Mechanical Properties for Titanium Alloy Ti-6Al-4V Produced Using LENS Technology

Materials ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 886 ◽  
Author(s):  
Aleksandra Szafrańska ◽  
Anna Antolak-Dudka ◽  
Paweł Baranowski ◽  
Paweł Bogusz ◽  
Dariusz Zasada ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Numerical Modelling ◽  
Optical Measurement ◽  
Electron Backscatter Diffraction ◽  
Material Behavior ◽  
Material Data ◽  
Loading Direction ◽  
Electron Microscopes ◽  
Net Shaping

This paper presents a characterization study of specimens manufactured from Ti-6Al-4V powder with the use of laser engineered net shaping technology (LENS). Two different orientations of the specimens were considered to analyze the loading direction influence on the material mechanical properties. Moreover, two sets of specimens, as-built (without heat treatment) and after heat treatment, were used. An optical measurement system was also adopted for determining deformation of the specimen, areas of minimum and the maximum principal strain, and an effective plastic strain value at failure. The loading direction dependence on the material properties was observed with a significant influence of the orientation on the stress and strain level. Microstructure characterization was examined with the use of optical and scanning electron microscopes (SEM); in addition, the electron backscatter diffraction (EBSD) was also used. The fracture mechanism was discussed based on the fractography analysis. The presented comprehensive methodology proved to be effective and it could be implemented for different materials in additive technologies. The material data was used to obtain parameters for the selected constitutive model to simulate the energy absorbing structures manufactured with LENS technology. Therefore, a brief discussion related to numerical modelling of the LENS Ti-6Al-4V alloy was also included in the paper. The numerical modelling confirmed the correctness of the acquired material data resulting in a reasonable reproduction of the material behavior during the cellular structure deformation process.

Effect of Heat Treatment on the Mechanical Properties of Wrought Al-Zn-Mg-Cu Alloy Cast by Rapid Solidification

2013 ◽  
Vol 765 ◽  
pp. 496-500 ◽  
Author(s):  
Dawid Kapinos ◽  
Marcin Szymanek ◽  
Bogusław Augustyn ◽  
Maciej Gawlik
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Rapid Solidification ◽  
Solution Heat Treatment ◽  
Grain Structure ◽  
Ultrafine Grain ◽  
Cu Alloy ◽  
Optimum Heat ◽  
Ultrafine Grain Structure ◽  
Alloy Cast

The article presents the change in mechanical properties of AlZn9Mg2.5Cu1.8 alloy resulting from the process of solution heat treatment and aging. The heat treatment was performed on a unique UMSA (Universal Metallurgical Simulator and Analyzer) device. The aim of the study was to determine optimum heat treatment parameters for the tested alloy of ultrafine grain structure obtained by Rapid Solidification (RS). To achieve this purpose, heat treatment to the T4 and T6 condition was carried out. The solution heat treatment was carried out at a constant temperature of 460 °C for 2 hours, while the time - temperature parameters of the aging process varied. The treatment undertaken resulted in improved mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document