Ultrafine Grain Evolution in Austenitic Stainless Steel during Large Strain Deformation and Subsequent Annealing

2012 ◽  
Vol 715-716 ◽  
pp. 273-278
Author(s):  
Andrey Belyakov ◽  
Kaneaki Tsuzaki ◽  
Rustam Kaibyshev
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Structural Changes ◽  
Volume Fraction ◽  
Subgrain Size ◽  
Large Strain ◽  
Structural Response ◽  
Subsequent Annealing ◽  
Ultrafine Grain ◽  
Average Size

The structural changes in a 304-type austenitic stainless steel during large strain cold rolling and subsequent annealing were studied. The severe deformation resulted in the development of highly elongated grains/subgrains aligned along the rolling axis. The transverse grain/subgrain size rapidly decreased to its minimal value of about 50 nm at relatively small strains of ~1 and then hardly changed upon following deformation. Such a structural response on cold working was associated with multiple twinning resulting in fast grain subdivision. The processing was accompanied by a partial martensitic transformation resulting in a decrease of austenite volume fraction to about 0.35 after straining to ε = 4.0. Isochronal annealing for 30 min was characterised by a gradual coarsening of grains, the average size of which increased to about 200 nm after heating to 800°C. The high elongation of ferrite grains facilitated simultaneous homogeneous nucleation of austenite grains throughout the matrix upon heating; and, therefore, promoted the development of ultrafine grained structure with the size of structural elements well below 1 micron.

Nanostructure Evolution in an Austenitic Stainless Steel Subjected to Multiple Forging at Ambient Temperature

2010 ◽  
Vol 667-669 ◽  
pp. 553-558 ◽  
Author(s):  
Andrey Belyakov ◽  
Kaneaki Tsuzaki ◽  
Rustam Kaibyshev
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Ambient Temperature ◽  
Structural Changes ◽  
Subgrain Size ◽  
Large Strain ◽  
Total Strain ◽  
Large Strains ◽  
Fast Kinetics ◽  
Cumulative Strain

Deformation behavior and structural changes were studied in a 304-type austenitic stainless steel subjected to large strain multiple forging at an ambient temperature. The number of forging passes was 10, leading to the total cumulative strain of 4.0. The yield stress rapidly increased to about 1000 MPa after the first forging pass and then gradually approached a saturation level of about 2000 MPa in large strains. The grain/subgrain size decreased to about 50 nm at total strain of about 2. This grain/subgrain size reduced a little upon further processing; and comprised 35 nm after a total strain of 4.0. The fast kinetics for grain refinement was associated with deformation twinning and strain-induced martensitic transformation. The both of them resulted in fast grain subdivision at relatively small strains.

Recrystallization in Nanostructured Austenitic Stainless Steel

2008 ◽  
Vol 584-586 ◽  
pp. 966-970 ◽  
Author(s):  
Agnieszka T. Krawczynska ◽  
Małgorzata Lewandowska ◽  
Krzysztof Jan Kurzydlowski
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Grain Growth ◽  
Structural Changes ◽  
True Strain ◽  
Equivalent Diameter ◽  
Uniform Microstructure ◽  
Lower Annealing Temperature ◽  
Average Size ◽  
Induced Changes

Recrystallization and grain growth were studied in an austenitic stainless steel 316LVM processed by hydrostatic extrusion (HE) to a total true strain of 2. HE processing produces in this material the microstructure which consists of nanoscale twins on average 19 nm in width and 168 nm in length. The samples after HE were annealed at various temperatures for 1 hour. The structural changes were investigated using TEM. The heat induced changes in nanotwinned austenitic steel are significantly different when compared to the ones in a conventionally deformed material. Microstructural changes take place at lower annealing temperature. Annealing at 600°C brings about a partial a nanostructure reorganization into nanograin of average size 54 nm. An uniform microstructure with nanograins of 68 nm in equivalent diameter was obtained after annealing at 700°C whereas conventional 316LVM steel fully recrystallizes after annealing at 900°C for 1h. Annealing at higher temperatures results in grain growth.

The Formation of Submicrometer Scale Grains in a Super304H Steel during Multiple Compressions at 700°C

2010 ◽  
Vol 667-669 ◽  
pp. 565-570 ◽  
Author(s):  
Marina Tikhonova ◽  
Valeriy Dudko ◽  
Andrey Belyakov ◽  
Rustam Kaibyshev
Keyword(s):  
Stainless Steel ◽  
Steady State ◽  
Austenitic Stainless Steel ◽  
Deformation Behavior ◽  
Structural Changes ◽  
Submicrocrystalline Structure ◽  
Ultrafine Grains ◽  
Maximum Value ◽  
Average Size ◽  
Super304h Steel

The deformation behavior and the microstructure evolution in a 304-type austenitic stainless steel were studied in multiple forging tests at temperature of 700°C. The flow stresses increased to its maximum value with straining to about 1 and, then, slightly decreased resulting in a steady state deformation behavior at strains above 3. The structural changes were characterized by the development of a spatial net of deformation subboundaries, the misorientations of which increased to the values typical of conventional grain boundaries. The number of ultrafine grains increased with straining, leading to development of submicrocrystalline structure. The fraction of submicrocrystalline structure composed of ultrafine grains with an average size of about 300 nm exceeded 0.7 after straining to 2.

Microstructure Evolution in a 304-Type Austenitic Stainless Steel during Multidirectional Forging at Ambient Temperature

2014 ◽  
Vol 783-786 ◽  
pp. 831-836 ◽  
Author(s):  
Alla Kipelova ◽  
Marina Odnobokova ◽  
Andrey Belyakov ◽  
Rustam Kaibyshev
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Microstructure Evolution ◽  
Room Temperature ◽  
Volume Fraction ◽  
True Strain ◽  
Nanocrystalline Structure ◽  
Multidirectional Forging ◽  
Average Size ◽  
Structural Mechanisms

The formation of nanocrystalline structure in a 304-type austenitic stainless steel during multidirectional forging (MDF) at room temperature was investigated. Initial coarse austenite grains with an average size of 50 μm were refined to about 80 nm by martensitic transformation during MDF to a total true strain of 2 and remained unchanged upon further deformation up to a strain of 4. The volume fraction of martensite achieved ~0.9 after forging to a strain of 1.6. The MDF at room temperature was accompanied by a significant hardening of the 304-type steel. The microhardness and the flow stress increased during forging and approached their saturations on the levels of about 5 GPa and 1.7 GPa, respectively, after total true strain of 2. The structural mechanisms responsible for microstructure evolution during severe deformation are discussed.

Structural Changes in a 9%Cr Creep Resistant Steel during Creep Test

2012 ◽  
Vol 715-716 ◽  
pp. 895-900
Author(s):  
Valeriy Dudko ◽  
Andrey Belyakov ◽  
Vladimir Skorobogatykh ◽  
Izabella Schenkova ◽  
Rustam Kaibyshev
Keyword(s):  
Structural Changes ◽  
Subgrain Size ◽  
Large Strain ◽  
Particle Growth ◽  
Second Phase ◽  
Second Phase Particles ◽  
Creep Rupture Test ◽  
Lath Structure ◽  
Creep Regime ◽  
Effective Stabilization

Structural changes in a 9%Cr martensitic steel after 1%, 4% creep and creep rupture test at 650°C and stress of 118 MPa were examined. Heat treatment provided the formation of tempered martensite lath structure (TMLS) in the steel. The precipitations of second phase particles along block and lath boundaries provide effective stabilization of the TMSL under annealing/aging condition. This structure hardly changed under creep conditions in grip portion of crept sample. Significant coarsening of both the second phase particles and the martensite laths takes place in neck portion. In addition, the latter ones lose their original morphology and are replaced by large strain-induced subgrains. It should be noted that the increase of subgrain size is in almost direct proportion to the particle growth during the creep to 4% strain. The rapid growth of martesite laths followed by their evolution to deformation subgrains takes place within the tertiary creep regime.

Magnetic Characterization of SUS316L Deformed by High Pressure Torsion

2011 ◽  
Vol 239-242 ◽  
pp. 1300-1303
Author(s):  
Hong Cai Wang ◽  
Minoru Umemoto ◽  
Innocent Shuro ◽  
Yoshikazu Todaka ◽  
Ho Hung Kuo
Keyword(s):  
Plastic Deformation ◽  
High Pressure ◽  
Stainless Steel ◽  
Phase Transformation ◽  
Austenitic Stainless Steel ◽  
Volume Fraction ◽  
High Pressure Torsion ◽  
Austenitic Matrix ◽  
Magnetic Characterization

SUS316L austenitic stainless steel was subjected to severe plastic deformation (SPD) by the method of high pressure torsion (HPT). From a fully austenitic matrix (γ), HPT resulted in phase transformation from g®a¢. The largest volume fraction of 70% a¢ was obtained at 0.2 revolutions per minute (rpm) while was limited to 3% at 5rpm. Pre-straining of g by HPT at 5rpm decreases the volume fraction of a¢ obtained by HPT at 0.2rpm. By HPT at 5rpm, a¢®g reverse transformation was observed for a¢ produced by HPT at 0.2rpm.

Effects of Deformation Mode on Resistivity Curve Used for Estimating Martensite Induced in Stainless Steel

2010 ◽  
Vol 638-642 ◽  
pp. 2992-2997 ◽  
Author(s):  
Hidefumi Date
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Linear Relation ◽  
Volume Fraction ◽  
Tensile Deformation ◽  
Deformation Mode ◽  
Transformation Process ◽  
Martensite Formation ◽  
Austenitic Phase ◽  
Ε Phase

The martensite induced in three types of austenitic stainless steel, which indicate the different stability of the austenitic phase (γ), were estimated by the resistivity measured during the tensile deformation or compressive deformation at the temperatures 77, 187 and 293 K. The resistivity curves were strongly dependent on the deformation mode. The volume fraction of the martensite (α’) was also affected by the deformation mode. The ε phase, which is the precursor of the martensite and is induced from the commencement of the deformation, decreased the resistivity. However, lots of defects generated by the deformation-induced martensite increased the resistivity. The experimental facts and the results shown by the modified parallelepiped model suggested a complicated transformation process depending on each deformation mode. The results shown by the model also suggested a linear relation between the resistivity and the martensite volume at the region of the martensite formation. The fact denoted that the resistivity is mostly not controlled by the austenite, ε phase and martensite, but by the defects induced due to the deformation-induced martensite.

Recovery in 15%Cr Ferritic Stainless Steel after Large Strain Deformation

2007 ◽  
Vol 558-559 ◽  
pp. 119-124
Author(s):  
Andrey Belyakov ◽  
Kaneaki Tsuzaki ◽  
Yoshisato Kimura ◽  
Yoshinao Mishima
Keyword(s):  
Stainless Steel ◽  
Low Temperature ◽  
Dislocation Density ◽  
Ambient Temperature ◽  
Ferritic Stainless Steel ◽  
Vickers Hardness ◽  
Subgrain Size ◽  
Large Strain ◽  
Internal Stresses ◽  
Cumulative Strain

15%Cr ferritic stainless steel was machined in rectangular samples and then processed by multiple forging to a total cumulative strain of 7.2 at an ambient temperature. The large strain deformation resulted in almost equiaxed submicrocrystalline structure with a mean grain/subgrain size of 230 nm and about 2.2×1014 m-2 dislocation density in grain/subgrain interiors. The annealing at a relatively low temperature of 500oC did not lead to any discontinuous recrystallizations. The grain/subgrain size and the interior dislocation density slightly changed to 240 nm and 2.1×1014 m-2, respectively, after annealing for 30 min, while the Vickers hardness decreased from 3140 MPa in the as-processed state to 2900 MPa. This annealing softening was attributed to remarkable release (by 50%) of internal stresses, which are associated with a non-equilibrium character of strain-induced grain/subgrain boundaries.

scholarly journals Surface Modification of a Nickel-Free Austenitic Stainless Steel by Low-Temperature Nitriding

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1845
Author(s):  
Francesca Borgioli ◽  
Emanuele Galvanetto ◽  
Tiberio Bacci
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Low Temperature ◽  
Stainless Steels ◽  
Volume Fraction ◽  
Surface Hardness ◽  
Austenitic Stainless Steels ◽  
Surface Layers ◽  
Modified Surface

Low-temperature nitriding allows to improve surface hardening of austenitic stainless steels, maintaining or even increasing their corrosion resistance. The treatment conditions to be used in order to avoid the precipitation of large amounts of nitrides are strictly related to alloy composition. When nickel is substituted by manganese as an austenite forming element, the production of nitride-free modified surface layers becomes a challenge, since manganese is a nitride forming element while nickel is not. In this study, the effects of nitriding conditions on the characteristics of the modified surface layers obtained on an austenitic stainless steel having a high manganese content and a negligible nickel one, a so-called nickel-free austenitic stainless steel, were investigated. Microstructure, phase composition, surface microhardness, and corrosion behavior in 5% NaCl were evaluated. The obtained results suggest that the precipitation of a large volume fraction of nitrides can be avoided using treatment temperatures lower than those usually employed for nickel-containing austenitic stainless steels. Nitriding at 360 and 380 °C for duration up to 5 h allows to produce modified surface layers, consisting mainly of the so-called expanded austenite or gN, which increase surface hardness in comparison with the untreated steel. Using selected conditions, corrosion resistance can also be significantly improved.

Sign in / Sign up

Export Citation Format

Share Document