Microstructure and Mechanical Properties of As-Rolled Mg-Zn-Gd-Ca-Mn Sheets

2014 ◽  
Vol 788 ◽  
pp. 68-73
Author(s):  
Sheng Shuan Dongye ◽  
Hong Yan ◽  
Xing Hao Du ◽  
Rong Shi Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Ambient Temperature ◽  
Hot Rolling ◽  
Basal Texture ◽  
Microstructure And Mechanical Properties ◽  
Zn Concentration ◽  
Elongation To Failure

The Mg-(4,6)Zn-1Ca-1RE-0.5Mn magnesium alloy sheets were processed by hot rolling, and the effect of Zn concentration on the microstructure and mechanical properties was investigated using OM,SEM and XRD technique. The Mg-4Zn-1Ca-1RE-0.5Mn sheet exhibits excellent tensile properties at ambient temperature with ultimate tensile strength of 332MPa and elongation to failure of 4.5%. The notable mechanical properties were attributed to fine DRX grains and large deformed grains with intense basal texture.

Effect of Bi on Microstructure and Mechanical Properties of Extruded AZ80-2Sn Magnesium Alloy

2018 ◽  
Vol 37 (1) ◽  
pp. 97-103 ◽  
Author(s):  
Hansong Xue ◽  
Xinyu Li ◽  
Weina Zhang ◽  
Zhihui Xing ◽  
Jinsong Rao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

AbstractThe effects of Bi on the microstructure and mechanical properties of AZ80-2Sn alloy were investigated. The results show that the addition of Bi within the as-cast AZ80-2Sn alloy promotes the formation of Mg3Bi2 phase, which can refine the grains and make the eutectic phases discontinuous. The addition of 0.5 % Bi within the as-extruded AZ80-2Sn alloy, the average grain size decreases to 12 μm and the fine granular Mg17Al12 and Mg3Bi2 phases are dispersed in the α-Mg matrix. With an increase in Bi content, the Mg17Al12 and Mg3Bi2 phases become coarsened and the grain size increases. The as-extruded AZ80-2Sn-0.5 %Bi alloy has the optimal properties, and the ultimate tensile strength, yield strength and elongation are 379.6 MPa, 247.1 MPa and 14.8 %, respectively.

Effects of Gd on the Microstructure and Mechanical Properties of Mg-3Sn Alloys

2013 ◽  
Vol 747-748 ◽  
pp. 245-250 ◽  
Author(s):  
Jun Luo ◽  
Rong Shi Chen ◽  
En Hou Han
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Volume Fraction ◽  
Microstructure And Mechanical Properties ◽  
Elongation To Failure ◽  
New Phase

The microstructure and mechanical properties of as-cast Mg-3Sn-xGd (x=0, 0.2, 1 wt.%) alloys were studied by using OM, SEM, EDX, XRD etc. With the increase of Gd, the formation of Mg2Sn phase was impeded and the MgSnGd phase formed and the volume fraction of this new phase obviously increased. The ultimate tensile strength and elongation to failure increased with dilute Gd addition but sharply decreased when the Gd addition comes to 1.34 wt.%. The possible reasons for the variation in microstructure and mechanical properties were discussed.

Effect of Extrusion Time on Microstructure and Mechanical Properties of AZ31B Magnesium Alloy Prepared by Solid-State Recycling

2011 ◽  
Vol 391-392 ◽  
pp. 559-563
Author(s):  
Shu Yan Wu ◽  
Ze Sheng Ji ◽  
Li Hua Wen ◽  
Hong Bo Li
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Solid State ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Dynamic Recrystallization ◽  
Stream Line ◽  
Alloy Matrix ◽  
State Process ◽  
Elongation To Failure

AZ31B magnesium alloys recycled by solid-state process from oxidized chip were extruded repeately. Microstructures and mechanical properties of recycled alloys for different extrusion times were studied. With the increasing extrusion times, the breaking degree and homogeneity of oxide increase and stream line feature of oxide become less obvious. Second extrusion make dynamic recrystallization microstructure of recycled alloy become more homogeneous and fine, but the microstructure is not refined furtherly after 3 and 4 times extrusion. The ultimate tensile strength increases with the increasing extrusion time, which resulting from the microstructure evolution during repeating extrusion and the enhanced bonding between oxide and magnesium alloy matrix. The elongation to failure of recycled alloy increases after second extrusion and continuously decreases after 3 and 4 time extrusion. This is determined not only by the variation of dynamic recrystallization microstructure and bonding strength between chips but also by the distribution status of oxide.

Effect of the Cyclic Extrusion and Compression Processing on Microstructure and Mechanical Properties of Al-1%Cu Alloy

2018 ◽  
Vol 780 ◽  
pp. 93-97
Author(s):  
Walaa Abdelaziem ◽  
Atef Hamada ◽  
Mohsen Abdel-Naeim Hassan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Cast Alloy ◽  
Surface Hardness ◽  
Grain Structure ◽  
Cu Alloy ◽  
Cu Alloys ◽  
Microstructure And Mechanical Properties ◽  
Elongation To Failure

The Simple Cyclic extrusion compression (SCEC) has been developed for producing Al-1%Cu alloys with fine microstructures and superior properties. SCEC method was applied for only two-passess.It was found that the grain structure was significantly reduced from 1500 μm to 100 μm after two passes of cyclic extrusion. The ultimate tensile strength and elongation to failure of as-cast alloy were 110 MPa and 12 %, respectively. However, the corresponding mechanical properties of the two pass CEC deformed alloy are 275 MPa and 35%, respectively. These findings ensure that a significant improvement in the grain structure has been achieved. In addition, cyclic extrusion deformation increased the surface hardness of the alloy by 50 % after two passes.

Microstructure and Mechanical Properties of AZ31B Magnesium Alloy Sheets Prepared by Extruding and Rolling

2006 ◽  
Vol 11-12 ◽  
pp. 653-656 ◽  
Author(s):  
Peng Xi Li ◽  
Bo Ping Zhang ◽  
Jing Yi Chen ◽  
Yi Fan Tu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Hot Rolling ◽  
Homogeneous Microstructure ◽  
Az31b Magnesium Alloy ◽  
Microstructure And Mechanical Properties ◽  
Processing Variables ◽  
Equiaxed Grains ◽  
Different Thickness

AZ31B Magnesium alloy sheets with about 1 mm in thickness were rolled by one pass and several passes from the extruded ingots with different thickness. The effects of processing variables on microstructure and mechanical properties of AZ31B Mg alloy sheets were investigated. XRD indicated that AZ31B magnesium alloy sheets have a dominant texture with (000l) orientated plane. The large deformation results in the formation of fine and homogeneous microstructure due to the recrystallization during extruding and hot-rolling. The thinnest sheet rolled by several passes showed equiaxed grains with 5-10μm in diameter. The fine grains result in the increase in the strength and the ductility. The tensile strength of the sheet rolled by several passes reached 292 MPa and the elongation was twice as larger as that rolled by one pass.

scholarly journals Mechanical Response of Al-1.09Mg2Si Alloy under Varying Mould and Thermal Ageing Conditions

2012 ◽  
Vol 2012 ◽  
pp. 1-7
Author(s):  
O. I. Sekunowo ◽  
G. I. Lawal ◽  
S. O. Adeosun
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Ambient Temperature ◽  
Mechanical Response ◽  
Ageing Time ◽  
Thermal Ageing ◽  
Alloy Ingot ◽  
Solution Treated ◽  
Crucible Furnace

Samples of the 6063 (Al-1.09Mg2Si) alloy ingot were melted in a crucible furnace and cast in metal and sand moulds, respectively. Standard tensile, hardness, and microstructural test specimens were prepared from cast samples, solution treated at 520∘C, soaked for 6 hrs, and immediately quenched at ambient temperature in a trough containing water to assume a supersaturated structure. The quenched specimens were then thermally aged at 175∘C for 3–7 hrs. Results show that at different ageing time, varied fractions of precipitates and intermetallics evolved in the specimens’ matrices which affect the resulting mechanical properties. The metal mould specimens aged for four hours (MTA-4) exhibited superior ultimate tensile strength of 247.8 MPa; microhardness, 68.5 HV; elongation, 28.2% . It is concluded that the extent of improvement in mechanical properties depends on the fractions, coherence, and distribution of precipitates along with the type of intermetallics developed in the alloy during ageing process.

Effects of Sr Addition on Mechanical Properties and Microstructure of Mg-6Al Magnesium Alloy

2011 ◽  
Vol 686 ◽  
pp. 120-124
Author(s):  
Jin Ping Fan ◽  
She Bin Wang ◽  
Bing She Xu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Strengthening Mechanism ◽  
Microstructure And Mechanical Properties ◽  
Higher Temperature ◽  
Lower Temperature

The effects of Sr addition on the mechanical properties and microstructure of Mg-6Al mag- nesium alloy both at 25 °C and at 175 °C were investigated by means of OM, SEM and EDS and XRD. Upon the Sr addition of 2%, the tensile strength was increased by 7.2% to 184.4MPa at 25 °C, while it was increased by 30% to 155.4MPa at 175 °C. The strengthening mechanism of Mg-6Al-xSr at lower temperature (25 °C) was different from that at higher temperature (175°C). The results show that the addition of strontium effectively improved the microstructure and mechanical properties of magnesium alloy.

scholarly journals Effects of Gd, Y Content on the Microstructure and Mechanical Properties of Mg-Gd-Y-Nd-Zr Alloy

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 790 ◽  
Author(s):  
Changping Tang ◽  
Kai Wu ◽  
Wenhui Liu ◽  
Di Feng ◽  
Xuezhao Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Solution Treatment ◽  
Age Hardening ◽  
Uniaxial Tensile ◽  
Microstructure And Mechanical Properties ◽  
Shaped Particle ◽  
Zr Alloy ◽  
Non Equilibrium

The effects of Gd, Y content on the microstructure and mechanical properties of Mg-Gd-Y-Nd-Zr alloy were investigated using hardness measurements, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), and uniaxial tensile testing. The results indicate that the alloys in as-cast condition mainly consist of α-Mg matrix and non-equilibrium eutectic Mg5.05RE (RE = Gd, Y, Nd). After solution treatment, the non-equilibrium eutectics dissolved into the matrix but some block shaped RE-rich particles were left at the grain boundaries and within grains. These particles are especially Y-rich and deteriorate the mechanical properties of the alloys. Both the compositions of the eutectic and the block shaped particle were independent of the total Gd, Y content of the alloys, but the number of the particles increases as the total Gd, Y content increases. The ultimate tensile strength increases as the total Gd, Y content decreases. A Mg-5.56Gd-3.38Y-1.11Nd-0.48Zr alloy with the highest ultimate tensile strength of 280 MPa and an elongation of 1.3% was fabricated. The high strength is attributed to the age hardening behavior and the decrease in block shaped particles.

scholarly journals Preparation and Mechanical Properties of ZK61-Y Magnesium Alloy Wheel Hub via Liquid Forging—Isothermal Forging Process

Metals ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 385
Author(s):  
Yushi Qi ◽  
Heng Wang ◽  
Lili Chen ◽  
Hongming Zhang ◽  
Gang Chen ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Heat Treatments ◽  
Second Phase ◽  
Phase Hardening ◽  
Isothermal Forging ◽  
Forging Process ◽  
Microstructure And Mechanical Properties ◽  
Alloy Wheel

A ZK61-Y magnesium (Mg) alloy wheel hub was prepared via liquid forging—isothermal forging process. The effects of Y-element contents on the microstructure and mechanical properties of liquid forging blanks were investigated. The formation order of the second phase was I-phase (Mg3Zn6Y) → W-phase (Mg3Zn3Y2) → Z-phase (Mg12ZnY) with the increase of the Y-element content. Meanwhile, the I-phase and Z-phase formed in the liquid forging process were beneficial to the grain refinement. The numerical simulation of the isothermal forging process was carried out to analyze the effects of forming temperature on the temperature and stress field in the forming parts using the software Deform-3D. Isothermal forging experiments and post heat treatments were conducted. The influence of isothermal forging temperature, heat treatment temperature and preservation time on the microstructure and mechanical properties of the forming parts were also studied. The dynamic recrystallization (DRX), second-phase hardening, and work hardening account for the improvement of properties after the isothermal forging process. The forming part forged at 380 °C displayed the outstanding properties. The elongation, yield strength, and ultimate tensile strength were 18.5%, 150 MPa and 315 MPa, respectively. The samples displayed an increased elongation and decreased strength after heat treatments. The 520 °C—1 h sample possessed the best mechanical properties, the elongation was 25.5%, the yield stress was 125 MPa and the ultimate tensile strength was 282 MPa. This can be ascribed to the recrystallization and the elimination of working hardening. Meanwhile, the second phase transformation (I-phase → W-phase → Mg2Y + MgZn2), dissolution, and decomposition can be observed, as well.

Sign in / Sign up

Export Citation Format

Share Document