scholarly journals The Effect of Clay Pozzolana-Cement-Composite on the Strength Development of a Hydraulic Backfill

2018 ◽  
Vol 18 (1) ◽  
pp. 32-38
Author(s):  
S. N. Eshun ◽  
Solomon Senyo Robert Gidigasu ◽  
S. K. Y. Gawu
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Unconfined Compressive Strength ◽  
Ordinary Portland Cement ◽  
Cement Content ◽  
Cylindrical Specimen ◽  
Cement Composite ◽  
Strength Development ◽  
Increased Risk ◽  
Economic Considerations

The study sought to investigate the potential application of clay pozzolana as a supplement for cement in hydraulic backfill, using classified tailings from AngloGold Ashanti, Obuasi Mine. The percentage of the Portland cement that could be substituted with the clay pozzolana to produce backfill with best strength was determined. 10%, 25%, 30%, 35% and 40% of the ordinary Portland cement were replaced with clay pozzolana and then mixed with tailings and water. The slurry produced was cast into cylindrical specimen of 50mm diameter by 120mm high and tested for compressive strength after curing for 7, 14, 21, 28 and 56 days. The results indicate that, clay pozzolana-cement composite has potential for application in hydraulic back fill production without increased risk to safety and dilution. It was noted that hydraulic backfill with 10%, 25%, 30% and 35% of the ordinary portland cement replaced with clay pozzolana had strengths greater than those obtained for ordinary portland cement alone. Ten percent (10%) pozzolana content gave the maximum strength followed by 25% pozzolana. It is recommended that for safety and economic considerations, the cement content should be replaced by 25% pozzolana in the production of backfills. Keywords: Hydraulic Backfill, Portland Cement, Clay Pozzolana, Unconfined Compressive Strength

scholarly journals Strength development of cement-treated sand using different cement types cured at different temperatures

2018 ◽  
Vol 195 ◽  
pp. 01006
Author(s):  
Lanh Si Ho ◽  
Kenichiro Nakarai ◽  
Kenta Eguchi ◽  
Takashi Sasaki ◽  
Minoru Morioka
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Cement Content ◽  
Bound Water ◽  
Pozzolanic Reaction ◽  
Strength Development ◽  
Different Temperatures ◽  
Early Strength

This study aimed to investigate the strength development of cement-treated sand using different cement types: ordinary Portland cement (OPC), high early strength Portland cement (HPC), and moderate heat Portland cement (MPC) cured at different temperatures. The cementtreated sand specimens were prepared with 8% of cement content and cured under sealed conditions at 20οC and 40οC, and mortar specimens were also prepared for reference. The results showed that the compressive strength of cement-treated sand increased in order of MPC, OPC, and HPC under high curing temperatures. It was interesting that the compressive strength of the specimens using HPC was much larger than that of the specimen using OPC and MPC under 20οC due to the larger amount of chemically bound water. Additionally, it was revealed that under high curing temperatures, the pozzolanic reaction was accelerated in the cement-treated sand; this may be caused by the high proportions of sand in the mixtures.

scholarly journals Chloride Ingress in Chemically Activated Calcined Clay-Based Cement

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Joseph Mwiti Marangu ◽  
Joseph Karanja Thiong’o ◽  
Jackson Muthengia Wachira
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Strength Development ◽  
Chloride Ingress ◽  
Calcined Clay ◽  
Apparent Diffusion Coefficients ◽  
Apparent Diffusion ◽  
Lower Porosity ◽  
Lower Chloride

Chloride-laden environments pose serious durability concerns in cement based materials. This paper presents the findings of chloride ingress in chemically activated calcined Clay-Ordinary Portland Cement blended mortars. Results are also presented for compressive strength development and porosity tests. Sampled clays were incinerated at a temperature of 800°C for 4 hours. The resultant calcined clay was blended with Ordinary Portland Cement (OPC) at replacement level of 35% by mass of OPC to make test cement labeled PCC35. Mortar prisms measuring 40 mm × 40 mm × 160 mm were cast using PCC35 with 0.5 M Na2SO4 solution as a chemical activator instead of water. Compressive strength was determined at 28th day of curing. As a control, OPC, Portland Pozzolana Cement (PPC), and PCC35 were similarly investigated without use of activator. After the 28th day of curing, mortar specimens were subjected to accelerated chloride ingress, porosity, compressive strength tests, and chloride profiling. Subsequently, apparent diffusion coefficients (Dapp) were estimated from solutions to Fick’s second law of diffusion. Compressive strength increased after exposure to the chloride rich media in all cement categories. Chemically activated PCC35 exhibited higher compressive strength compared to nonactivated PCC35. However, chemically activated PCC35 had the least gain in compressive strength, lower porosity, and lower chloride ingress in terms of Dapp, compared to OPC, PPC, and nonactivated PCC35.

scholarly journals Mechanical Properties of OPC - Geocement Concrete

2019 ◽  
Vol 8 (4) ◽  
pp. 3733-3736
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
External Heat ◽  
Partial Replacement ◽  
Strength Development ◽  
Strength Increase ◽  
Heat Curing ◽  
Compressive Strength Development

Nowadays geopolymer concretes are subjected to heat curing. A large amount of highly corrosive and the hygroscopic alkaline activators are nowadays generally utilized in producing geopolymer concretes. In this paper, hybrid Ordinary Portland Cement (OPC) and geopolymer mixes are developed. The mainly used activator id the Solid potassium carbonate at different percentage is used as 5% & 10% of the weight of geopolymeric materials and OPC was blended with geopolymeric materials in different proportions. By adding cement, improves all the geopolymer properties except workability. By Applying external heat, it plays an important role in gaining strength. Strength gained by the absence of external heat is achieved by using Portland cement as a partial replacement of geocement. The influence of OPC content on the compressive strength development is investigated, and the optimized amount of solid activator to be used in the mix is also investigated. It is observed that percentage of strength increase decreases from52.24% to 14.77% as the OPC content increased from 20% to 60%.

scholarly journals Mechanical Properties of Sandy Soil Improved with Cement and Nanosilica

2015 ◽  
Vol 5 (1) ◽  
Author(s):  
Asskar Janalizadeh Choobbasti ◽  
Ali Vafaei ◽  
Saman Soleimani Kutanaei
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Sandy Soil ◽  
Unconfined Compressive Strength ◽  
Cement Content ◽  
Cylindrical Specimen ◽  
Engineering Properties ◽  
Nano Silica ◽  
Cement Based Materials ◽  
Nanosilica Particles

AbstractIn the literature, studies show that nanosilica particles and artificial pozzolans possessing can improve structural properties of cement-based materials. This paper studies the effect of cement and nanosilica on the engineering properties (compaction, unconfined compressive strength) of sand. Three different cement ratios (5, 9, and 14% by weight of dry sand) were mixed with four different nano silica ratios (0, 5, 10, and 15% by weight of cement), and then compacted into a cylindrical specimen. The results of the study presented that the addition of the cement and nanosilica improves the engineering properties of sands. The increase of maximum dry unitweight of sand was noted with the increase in the cement content. The presence of nanosilica in optimal percentages can significantly improve the mechanical properties of cement sand.

scholarly journals The potential use of pumice in mine backfill

2020 ◽  
Vol 1 ◽  
Author(s):  
Mohammed A. Hefni
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Mining Industry ◽  
Strength Development ◽  
Natural Pozzolan ◽  
Mine Backfill ◽  
Natural Pozzolans ◽  
Cemented Backfill ◽  
Compressive Strength Development ◽  
Potential Use

Abstract The use of natural pozzolans in concrete applications is gaining more attention because of the associated environmental, economic, and technical benefits. In this study, reference cemented mine backfill samples were prepared using Portland cement, and experimental samples were prepared by partially replacing Portland cement with 10 or 20 wt.% fly ash as a byproduct (artificial) pozzolan or pumice as a natural pozzolan. Samples were cured for 7, 14, and 28 days to investigate uniaxial compressive strength development. Backfill samples containing 10 wt.% pumice had almost a similar compressive strength as reference samples. There is strong potential for pumice to be used in cemented backfill to minimize costs, improve backfill properties, and promote the sustainability of the mining industry.

Study on Waterproof and Water-Resistant Properties of Gypsum

2012 ◽  
Vol 476-478 ◽  
pp. 1585-1588
Author(s):  
Hong Pan ◽  
Guo Zhong Li
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Ordinary Portland Cement ◽  
Experimental Results ◽  
Softening Coefficient

The comprehensively modified effect of cement, VAE emulsion and self-made acrylic varnish on mechanical and water-resistant properties of gypsum sample was investigated and microstructure of gypsum sample was analyzed. Experimental results exhibit that absolutely dry flexural strength, absolutely dry compressive strength, water absorption and softening coefficient of gypsum specimen with admixture of 10% ordinary Portland cement and 6% VAE emulsion and acrylic varnish coated on its surface can respectively reach to 5.11MPa , 10.49 MPa, 8.32% and 0.63, respectively.

scholarly journals Strength Development and Elemental Distribution of Dolomite/Fly Ash Geopolymer Composite under Elevated Temperature

Materials ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 1015 ◽  
Author(s):  
Emy Aizat Azimi ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Petrica Vizureanu ◽  
Mohd Arif Anuar Mohd Salleh ◽  
Andrei Victor Sandu ◽  
...  
Keyword(s):  
Elevated Temperature ◽  
Fly Ash ◽  
Portland Cement ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Liquid Sodium ◽  
Strength Development ◽  
Elemental Distribution ◽  
Distribution Analysis ◽  
Geopolymer Composites

A geopolymer has been reckoned as a rising technology with huge potential for application across the globe. Dolomite refers to a material that can be used raw in producing geopolymers. Nevertheless, dolomite has slow strength development due to its low reactivity as a geopolymer. In this study, dolomite/fly ash (DFA) geopolymer composites were produced with dolomite, fly ash, sodium hydroxide, and liquid sodium silicate. A compression test was carried out on DFA geopolymers to determine the strength of the composite, while a synchrotron Micro-Xray Fluorescence (Micro-XRF) test was performed to assess the elemental distribution in the geopolymer composite. The temperature applied in this study generated promising properties of DFA geopolymers, especially in strength, which displayed increments up to 74.48 MPa as the optimum value. Heat seemed to enhance the strength development of DFA geopolymer composites. The elemental distribution analysis revealed exceptional outcomes for the composites, particularly exposure up to 400 °C, which signified the homogeneity of the DFA composites. Temperatures exceeding 400 °C accelerated the strength development, thus increasing the strength of the DFA composites. This appears to be unique because the strength of ordinary Portland Cement (OPC) and other geopolymers composed of other raw materials is typically either maintained or decreases due to increased heat.

scholarly journals The Effect of Nano Metakaolin Material on Some Properties of Concrete

2013 ◽  
Vol 6 (1) ◽  
pp. 50-61
Author(s):  
Amer M. Ibrahem ◽  
Shakir A. Al-Mishhadani ◽  
Zeinab H.Naji
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Portland Cement ◽  
Water Absorption ◽  
Thermal Activation ◽  
Ordinary Portland Cement ◽  
Splitting Tensile Strength ◽  
Kaolin Clay ◽  
Cement Ratio ◽  
Water Cement Ratio

This investigation aimed to study the effect of nano metakaolin ( NMK ) on some properties (compressive strength ,splitting tensile strength & water absorption ) of concrete. The nano metakaolin (NMK) was prepared by thermal activation of kaolin clay for 2 hours at 750 Ċ. The cement used in this investigation consists of ordinary Portland cement (OPC). The OPC was partially substituted by NMK of ( 3, 5 & 10%) by weight of cement. The C45 concrete was prepared , using water/cement ratio ( W/c) of (0.53) .The Water absorption was tested at 28 days while the tests (compressive strength ,splitting tensile strength) were tested at ages of (7, 28, 60,& 90) days . The compressive strength and splitting tensile strength of concrete with NMK were higher than that of reference concrete with the same W/c ratio.The improvement in the compressive strength when using NMK was (42.2, 55.8 , 63.1% ) at age 28 days for ( 3%, 5%, &10% ) replacement of NMK respectively whereas the improvement in the splitting tensile strength was (0% , 36% & 46.8 %) at age of 28 days when using (3%, 5%, &10% ) NMK respectively. The improvement in the water absorption was (16.6%, 21.79%, &25.6 ) when using (3, 5, &10% )NMK.

Sign in / Sign up

Export Citation Format

Share Document