scholarly journals Natural Nanoporous Filter Material as a New High-Efficiency Natural Adsorbent to Remove Textile Dyes

2020 ◽  
Vol 15 ◽  
pp. 16-23
Author(s):  
Chin-Ya Kuo ◽  
Hsiao-Han Liu
Keyword(s):  
Uniform Distribution ◽  
High Efficiency ◽  
Low Cost ◽  
Mathematic Model ◽  
Filter Material ◽  
Textile Dyes ◽  
Physical Processes ◽  
Natural Adsorbents ◽  
Different Temperatures ◽  
Time Courses

The objective of this paper is to perform the innovation design of removing most textile dyes that are harmful to the environment and might induce cancer. However, many methodologies had been developed for various chemical and physical processes to remove different dyes, such as ozone oxidation, electrochemical methods, chemical coagulation, hypochlorite oxidation, and adsorption to remove dyes from wastewater. A novel nanoporous filter methodology and mathematic simulations for adsorption were established as an effective medium for removing dyes from wastewater which was compared to other expensive treatments. The different concentrations of the dye liquid are used as a tester, and the different concentrations of nanoporous adsorbent were added in a uniform distribution and were tested with different time courses and under different temperatures. The final readings were measured by a spectrophotometer and fit into a mathematic model. The result indicates that this nanoporous and natural adsorbents are very good at cleaning the dyes in this system. The fit-in mathematic models could be applied in these tests which can be used in the industrial conditions for a low cost without secondary dye pollutions.

scholarly journals Superior Degradation Performance of Nanoporous Copper Catalysts on Methyl Orange

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 913
Author(s):  
Jinyi Wang ◽  
Sen Yang
Keyword(s):  
Activation Energy ◽  
Methyl Orange ◽  
High Efficiency ◽  
Low Cost ◽  
Degradation Process ◽  
Copper Catalysts ◽  
Reaction Rate Constant ◽  
Nanoporous Structure ◽  
Intra Particle Diffusion ◽  
Different Temperatures

The development of low-cost and high-efficiency catalysts for wastewater treatment is of great significance. Herein, nanoporous Cu/Cu2O catalysts were synthesized from MnCu, MnCuNi, and MnCuAl with similar ligament size through one-step dealloying. Meanwhile, the comparisons of three catalysts in performing methyl orange degradation were investigated. One of the catalysts possessed a degradation efficiency as high as 7.67 mg·g−1·min−1. With good linear fitting by the pseudo-first-order model, the reaction rate constant was evaluated. In order to better understand the degradation process, the adsorption behavior was considered, and it was divided into three stages based on the intra-particle diffusion model. Three different temperatures were applied to explore the activation energy of the degradation. As a photocatalytic agent, the nanoporous structure of Cu/Cu2O possessed a large surface area and it also had low activation energy, which were beneficial to the excellent degradation performance.

scholarly journals Adsorption of Cr(VI) and Cu(II) from aqueous solutions by biochar derived from Chaenomeles sinensis seed

2019 ◽  
Vol 80 (12) ◽  
pp. 2260-2272 ◽  
Author(s):  
Xiaoling Hu ◽  
Jianyang Song ◽  
Hongyu Wang ◽  
Wei Zhang ◽  
Bin Wang ◽  
...  
Keyword(s):  
Heavy Metal ◽  
High Efficiency ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Heavy Metal Remediation ◽  
Chaenomeles Sinensis ◽  
Wide Ph Range ◽  
Different Temperatures ◽  
Isotherms And Thermodynamics ◽  
Ph Range

Abstract In order to utilize the discarded Chaenomeles sinensis seed (CSS) and develop low-cost biochar for heavy metal pollution control, this study pyrolyzed CSS to prepare biochar at three different temperatures (300, 450 and 600 °C). The physicochemical properties of CSS biochar such as elemental composition, surface area, surface morphology and surface functional groups were characterized. Its adsorption properties including kinetics, isotherms and thermodynamics were studied. The results showed that the adsorption equilibrium was reached at 5 h, which was relatively fast. CSS biochar prepared at 450 °C (CSS450) had the maximum adsorption capacity for Cr(VI) and Cu(II), which was 93.19 mg/g and 105.12 mg/g, respectively. The thermodynamic parameter ΔG0 < 0 and the isotherm parameter RL between 0 and 1 all revealed the feasibility and spontaneity of the adsorption process. The removal of Cr(VI) exhibited high efficiency in a wide pH range (1–10), while the removal of Cu(II) was pH-dependent and optimal at pH = 6. The coexisting ions in the solution showed slight inhibition of the adsorption of Cr(VI) and Cu(II). Additionally, Cu(II) exhibited better affinity for CSS450 than Cr(VI) in dynamic adsorption. This is the first study to prepare biochar from CSS and confirms its potential application for heavy metal remediation.

scholarly journals Research on Dynamic Facility Layout Problem of Manufacturing Unit Considering Human Factors

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Jinying Li ◽  
Xin Tan ◽  
Jinchao Li
Keyword(s):  
Industry 4.0 ◽  
High Efficiency ◽  
Low Cost ◽  
Facility Layout ◽  
Mathematic Model ◽  
Human Beings ◽  
Human Machine Interaction ◽  
Bee Colony ◽  
Penalty Factor ◽  
Adaptive Penalty

As many said, industry 4.0 is an epoch-making revolution which brought the manufacturing market much faster changes and severer competitions. As an important part of the manufacturing system, facility layout has direct impact on business benefit; at the same time, despite the intelligent factory, intelligent production has its own characteristics. However, there is one point on which industry and academia have basically formed a consensus: it is not true that industry 4.0 does not need human beings; on the contrary, human initiative plays an unabated role in the development of industry 4.0. This paper will focus on the dynamic facility layout of the manufacturing unit. Based on the system above and the traditional optimization model, a mathematic model is built to find the best solution combining safety, sustainability, high efficiency, and low cost. And penalty function with adaptive penalty factor and advanced artificial bee colony algorithm is used to solve the constrained model. In the end, by studying few cases, the model is proved to be effective in both efficiency improvement and the implementation of safe and comfort human-machine interaction.

Influence of MBE Growth Conditions on Dislocation Densities of GaAs/Ge Epilayers Grown on Silicon Substrates

1985 ◽  
Vol 43 ◽  
pp. 364-365
Author(s):  
K.M. Hones ◽  
P. Sheldon ◽  
B.G. Yacobi ◽  
A. Mason
Keyword(s):  
High Efficiency ◽  
Lattice Mismatch ◽  
Low Cost ◽  
Growth Conditions ◽  
Nonradiative Recombination ◽  
Device Structure ◽  
Si Substrates ◽  
Transmission Electron ◽  
Dislocation Densities ◽  
Dislocation Type

There is increasing interest in growing epitaxial GaAs on Si substrates. Such a device structure would allow low-cost substrates to be used for high-efficiency cascade- junction solar cells. However, high-defect densities may result from the large lattice mismatch (∼4%) between the GaAs epilayer and the silicon substrate. These defects can act as nonradiative recombination centers that can degrade the optical and electrical properties of the epitaxially grown GaAs. For this reason, it is important to optimize epilayer growth conditions in order to minimize resulting dislocation densities. The purpose of this paper is to provide an indication of the quality of the epitaxially grown GaAs layers by using transmission electron microscopy (TEM) to examine dislocation type and density as a function of various growth conditions. In this study an intermediate Ge layer was used to avoid nucleation difficulties observed for GaAs growth directly on Si substrates. GaAs/Ge epilayers were grown by molecular beam epitaxy (MBE) on Si substrates in a manner similar to that described previously.

Improvement of Ti/RuO2–IrO2 Anode Lifetime and Electrocatalytical Properties by Using an Eco-Friendly Thermal Decomposition Method Using Polyvinyl Alcohol as Solvent

2019 ◽  
Author(s):  
Charlys Bezerra ◽  
Géssica Santos ◽  
Marilia Pupo ◽  
Maria Gomes ◽  
Ronaldo Silva ◽  
...  
Keyword(s):  
Thermal Decomposition ◽  
Polyvinyl Alcohol ◽  
High Efficiency ◽  
Electrochemical Impedance ◽  
Pechini Method ◽  
Low Cost ◽  
Charge Transfer Resistance ◽  
Transfer Resistance ◽  
Calcination Temperatures ◽  
Service Lifetime

<p>Electrochemical oxidation processes are promising solutions for wastewater treatment due to their high efficiency, easy control and versatility. Mixed metal oxides (MMO) anodes are particularly attractive due to their low cost and specific catalytic properties. Here, we propose an innovative thermal decomposition methodology using <a>polyvinyl alcohol (PVA)</a> as a solvent to prepare Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes. Comparative anodes were prepared by conventional method employing a polymeric precursor solvent (Pechini method). The calcination temperatures studied were 300, 400 and 500 °C. The physical characterisation of all materials was performed by X-ray diffraction and scanning electron microscopy coupled with energy dispersive spectroscopy, while electrochemical characterisation was done by cyclic voltammetry, accelerated service lifetime and electrochemical impedance spectroscopy. Both RuO<sub>2</sub> and IrO<sub>2</sub> have rutile-type structures for all anodes. Rougher and more compact surfaces are formed for the anodes prepared using PVA. Amongst temperatures studied, 300 °C using PVA as solvent is the most suitable one to produce anodes with expressive increase in voltammetric charge (250%) and accelerated service lifetime (4.3 times longer) besides reducing charge-transfer resistance (8 times lower). Moreover, the electrocatalytic activity of the anodes synthesised with PVA toward the Reactive Blue 21 dye removal in chloride medium (100 % in 30 min) is higher than that prepared by Pechini method (60 min). Additionally, the removal total organic carbon point out improved mineralisation potential of PVA anodes. Finally, this study reports a novel methodology using PVA as solvent to synthesise Ti/RuO<sub>2</sub>–IrO<sub>2</sub> anodes with improved properties that can be further extended to synthesise other MMO compositions.</p>

Contradiction Analysis and Solution in the R&D of High-Power Solar LED Street Lamp Controller

2019 ◽  
Vol 12 (1) ◽  
pp. 12-19
Author(s):  
Zhengwang Xu ◽  
Wei Mei ◽  
Jiaqi Yu ◽  
Jiarui Zhang ◽  
Yuchun Yi ◽  
...  
Keyword(s):  
Power Supply ◽  
High Efficiency ◽  
Low Cost ◽  
Solar Panel ◽  
Battery Voltage ◽  
Supply Circuit ◽  
Led Light ◽  
Power Supply Circuit ◽  
Side Mode ◽  
Dual Power

As being restricted by factors such as cost, efficiency and size, the development of high-power solar LED street light controller is faced with plenty of difficulties. In case that a structure of two independent DC/DC is applied as the main circuit, it has to face problems such as large size and high cost; in case of applying the bidirectional BUCK/BOOST circuit, it requires change-over switches to control the solar panel and LED light. As being restricted by withstanding voltage, on-resistance and cost, a PMOS device cannot be used as the change-over switch of solar panel and LED light. However, when being used as a change-over switch, an NMOS device must apply the low-side mode under which the negative ends of the mentioned three parts are cut off. In the condition of applying the low-side mode, a differential circuit must be used to detect the voltage of the solar panel. Furthermore, in order to make sure batteries can still be regularly charged after wearing out in daylight, the controller must be supplied with power through a dual power supply circuit that can obtain power from both the solar panel and the battery. The demander has a requirement on extremely low standby power consumption of the product, and thus it is necessary to minimize the circuit that is live while working in standby mode. Methods: The bidirectional BUCK/BOOST circuit structure is applied to the main circuit to realize a higher change-over efficiency while giving considerations to both cost and size. The NMOS device, model IRFB4410ZPBF, with a price of about three yuan, is used as the switching device, and the low-side mode is applied, that is the switches inserted in between negative end of the solar panel or LED light and that of the DC/DC circuit. The low-cost rail-to-rail operational amplifier LM358 is used to form a differential amplification circuit for detecting the voltage of the solar panel. A XL1509-12E1 chip that only costs 0.88 yuan/pc is selected as the main change-over chip for the power supply, which has realized the highly-efficient and low-cost change-over of the power supply. A dual power supply circuit and a step-down protective circuit are designed for the XL1509-12E1 change-over chip. By comparing solar panel voltage with battery voltage, the solar panel booting circuit is realized. Only when solar panel voltage is higher than battery voltage, does the system program start to power it up for running, so that the outage of most of the circuits of the system under standby mode does not consume energy. Furthermore, the solar panel voltage detecting circuit, the solar panel booting circuit and several return difference functions are corrected during system debugging. Results: The circuit board of the entire controller features small size, low cost and high efficiency. It measures about 100*62*18mm in size, costs about 60 yuan, and the charge/discharge change-over efficiency reaches up to over 95%. The controller has many functions: it is capable of operating within a large scope, in which, solar panel voltage is subject to 15~50V, LED light voltage is subject to 15~60V, battery voltage is subject to 10~35V and battery-end charge/discharge current is 10A; it is capable of adapting to monocrystalline silicon/multicrystalline silicon/thin-film and many other kinds of solar panels, as well as lithium/lead-acid and many other kinds of batteries; it is capable of detecting the conversion of day and night, automatically controlling charging and discharging and automatically making adaptive adjustment according to seasonal variations; the current to be consumed during standby will be maintained below 3mA, and thus the power consumption is extremely low. Conclusion: By selecting the bidirectional BUCK/BOOST circuit structure, applying low-side mode for switching of solar panel and LED light, using a differential circuit to detect solar panel voltage, using a low-cost DC/DC chip to realize power supply change-over, designing a dual power supply circuit, introducing solar panel booting circuit and other hardware design, as well as MPPT algorithm, state recognition and control, return difference control and other software design, a solar LED street light control product featuring small size, low cost, high efficiency and multiple functions is successfully developed.

scholarly journals Chemical Modification of Combusted Coal Gangue for U(VI) Adsorption: Towards a Waste Control by Waste Strategy

2021 ◽  
Vol 13 (15) ◽  
pp. 8421
Author(s):  
Yuan Gao ◽  
Jiandong Huang ◽  
Meng Li ◽  
Zhongran Dai ◽  
Rongli Jiang ◽  
...  
Keyword(s):  
Structural Analysis ◽  
High Efficiency ◽  
Low Cost ◽  
Chemical Activation ◽  
Cost Effective ◽  
Coal Gangue ◽  
Order Kinetic ◽  
Practical Applications ◽  
Detailed Structural Analysis ◽  
Alkaline Conditions

Uranium mining waste causes serious radiation-related health and environmental problems. This has encouraged efforts toward U(VI) removal with low cost and high efficiency. Typical uranium adsorbents, such as polymers, geopolymers, zeolites, and MOFs, and their associated high costs limit their practical applications. In this regard, this work found that the natural combusted coal gangue (CCG) could be a potential precursor of cheap sorbents to eliminate U(VI). The removal efficiency was modulated by chemical activation under acid and alkaline conditions, obtaining HCG (CCG activated with HCl) and KCG (CCG activated with KOH), respectively. The detailed structural analysis uncovered that those natural mineral substances, including quartz and kaolinite, were the main components in CCG and HCG. One of the key findings was that kalsilite formed in KCG under a mild synthetic condition can conspicuous enhance the affinity towards U(VI). The best equilibrium adsorption capacity with KCG was observed to be 140 mg/g under pH 6 within 120 min, following a pseudo-second-order kinetic model. To understand the improved adsorption performance, an adsorption mechanism was proposed by evaluating the pH of uranyl solutions, adsorbent dosage, as well as contact time. Combining with the structural analysis, this revealed that the uranyl adsorption process was mainly governed by chemisorption. This study gave rise to a utilization approach for CCG to obtain cost-effective adsorbents and paved a novel way towards eliminating uranium by a waste control by waste strategy.

scholarly journals A Multi-Loop Vehicle-Counting Method under Gray Mode and RGB Mode

2021 ◽  
Vol 11 (15) ◽  
pp. 6831
Author(s):  
Yue Chen ◽  
Jian Lu
Keyword(s):  
Intelligent Transportation Systems ◽  
High Efficiency ◽  
Road Traffic ◽  
Low Cost ◽  
Rapid Development ◽  
Intelligent Transportation ◽  
Transportation Systems ◽  
Counting Method ◽  
Moving Vehicle ◽  
Available Information

With the rapid development of road traffic, real-time vehicle counting is very important in the construction of intelligent transportation systems (ITSs). Compared with traditional technologies, the video-based method for vehicle counting shows great importance and huge advantages in its low cost, high efficiency, and flexibility. However, many methods find difficulty in balancing the accuracy and complexity of the algorithm. For example, compared with traditional and simple methods, deep learning methods may achieve higher precision, but they also greatly increase the complexity of the algorithm. In addition to that, most of the methods only work under one mode of color, which is a waste of available information. Considering the above, a multi-loop vehicle-counting method under gray mode and RGB mode was proposed in this paper. Under gray and RGB modes, the moving vehicle can be detected more completely; with the help of multiple loops, vehicle counting could better deal with different influencing factors, such as driving behavior, traffic environment, shooting angle, etc. The experimental results show that the proposed method is able to count vehicles with more than 98.5% accuracy while dealing with different road scenes.

scholarly journals Research on the Performance of Solar Aided Power Generation System Based on Annular Fresnel Solar Concentrator

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1579
Author(s):  
Heng Zhang ◽  
Na Wang ◽  
Kai Liang ◽  
Yang Liu ◽  
Haiping Chen
Keyword(s):  
Power Generation ◽  
High Efficiency ◽  
Low Cost ◽  
Economic Index ◽  
Partial Replacement ◽  
Solar Concentrator ◽  
Small Disturbance ◽  
Step Size ◽  
Water Matrix ◽  
Cost Utilization

A solar-aided power generation (SAPG) system effectively promotes the high efficiency and low cost utilization of solar energy. In this paper, the SAPG system is represented by conventional coal-fired units and an annular Fresnel solar concentrator (AFSC) system. The annular Fresnel solar concentrator system is adopted to generate solar steam to replace the extraction steam of the turbine. According to the steam–water matrix equation and improved Flugel formula, the variable conditions simulation and analysis of the thermo-economic index were proposed by Matlab. Furthermore, in order to obtain the range of small disturbance, the method of partial replacement is used, that is, the extraction steam of the turbine is replaced from 0 to 100% with a step size of 20%. In this work, a SAPG system is proposed and its thermo-economic index and small disturbance scope are analyzed. The results show that the SAPG system is energy-saving, and the application scope of small disturbance is related to the quantity of the extraction steam and evaluation index.

Sign in / Sign up

Export Citation Format

Share Document