scholarly journals Adsorption of Cr(VI) and Cu(II) from aqueous solutions by biochar derived from Chaenomeles sinensis seed

2019 ◽  
Vol 80 (12) ◽  
pp. 2260-2272 ◽  
Author(s):  
Xiaoling Hu ◽  
Jianyang Song ◽  
Hongyu Wang ◽  
Wei Zhang ◽  
Bin Wang ◽  
...  
Keyword(s):  
Heavy Metal ◽  
High Efficiency ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Heavy Metal Remediation ◽  
Chaenomeles Sinensis ◽  
Wide Ph Range ◽  
Different Temperatures ◽  
Isotherms And Thermodynamics ◽  
Ph Range

Abstract In order to utilize the discarded Chaenomeles sinensis seed (CSS) and develop low-cost biochar for heavy metal pollution control, this study pyrolyzed CSS to prepare biochar at three different temperatures (300, 450 and 600 °C). The physicochemical properties of CSS biochar such as elemental composition, surface area, surface morphology and surface functional groups were characterized. Its adsorption properties including kinetics, isotherms and thermodynamics were studied. The results showed that the adsorption equilibrium was reached at 5 h, which was relatively fast. CSS biochar prepared at 450 °C (CSS450) had the maximum adsorption capacity for Cr(VI) and Cu(II), which was 93.19 mg/g and 105.12 mg/g, respectively. The thermodynamic parameter ΔG0 < 0 and the isotherm parameter RL between 0 and 1 all revealed the feasibility and spontaneity of the adsorption process. The removal of Cr(VI) exhibited high efficiency in a wide pH range (1–10), while the removal of Cu(II) was pH-dependent and optimal at pH = 6. The coexisting ions in the solution showed slight inhibition of the adsorption of Cr(VI) and Cu(II). Additionally, Cu(II) exhibited better affinity for CSS450 than Cr(VI) in dynamic adsorption. This is the first study to prepare biochar from CSS and confirms its potential application for heavy metal remediation.

scholarly journals Functionalized Porous Nanoscale Fe3O4 Particles Supported Biochar From Peanut Shell For Pb(II) Ions Removal From Landscape Wastewater

2021 ◽  
Author(s):  
Xiaojun Jin ◽  
Renrong Liu ◽  
Huifang Wang ◽  
Li Han ◽  
Muqing Qiu ◽  
...  
Keyword(s):  
Heavy Metal ◽  
High Efficiency ◽  
Adsorption Process ◽  
Low Cost ◽  
Agricultural Waste ◽  
Maximum Adsorption Capacity ◽  
Complexation Reaction ◽  
Order Kinetic ◽  
Peanut Shell ◽  
Adsorption Mechanisms

Abstract The large amounts of heavy metal from landscape wastewater have become serious problems of environmental pollution and risks for human health. It affects the growth of plant and aquatic, and leads to the destruction of landscape. Therefore, the development of efficient novel adsorbent is a very important for treatment of heavy metal. A low-cost and easily obtained agricultural waste (Peanut Shell) was modified by nanoscale Fe3O4 particles. Then, the functionalized porous nanoscale Fe3O4 particles supported biochar from peanut shell (PS-Fe3O4) for removal of Pb(II) ions from aqueous solution was investigated. The characterization of PS-Fe3O4 composites showed that PS from peanut shell was successfully coated with porous nanoscale Fe3O4 particles. The pseudo second-order kinetic model and Langmuir model were more fitted for describing the adsorption process of Pb(II) ions in solution. The maximum adsorption capacity of Pb(II) ions removal in solution by PS-Fe3O4 composites could reach 188.68 mg/g. The adsorption process of Pb(II) ions removal by PS-Fe3O4 composites was a spontaneous and endothermic process. The adsorption mechanisms of Pb(II) ions by PS-Fe3O4 composites were mainly controlled by the chemical adsorption process. They included Fe-O coordination reaction, co-precipitation, complexation reaction and ion exchange. PS-Fe3O4 composites were thought as a low-cost, good regeneration performance and high efficiency adsorption material for removal of Pb(II) ions in solution.

scholarly journals Preparation and Characterization of High-Efficiency Magnetic Heavy Metal Capture Flocculants

Water ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 1732
Author(s):  
Yuanyuan Yu ◽  
Yongjun Sun ◽  
Jun Zhou ◽  
Aowen Chen ◽  
Kinjal J. Shah
Keyword(s):  
Heavy Metal ◽  
Reaction Time ◽  
High Efficiency ◽  
Removal Rate ◽  
Low Cost ◽  
Monomer Concentration ◽  
Synthesis Process ◽  
Response Surface Optimization ◽  
Metal Capture ◽  
Total Monomer Concentration

In this study, a high-efficiency magnetic heavy metal flocculant MF@AA was prepared based on carboxymethyl chitosan and magnetic Fe3O4. It was characterized by SEM, FTIR, XPS, XRD and VSM, and the Cu(II) removal rate was used as the evaluation basis for the preparation process. The effects of AMPS content, total monomer concentration, photoinitiator concentration and reaction time on the performance of MF@AA flocculation to remove Cu(II) were studied. The characterization results show that MF@AA has been successfully prepared and exhibits good magnetic induction characteristics. The synthesis results show that under the conditions of 10% AMPS content, 35% total monomer concentration, 0.04% photoinitiator concentration, and 1.5 h reaction time, the best yield of MF@AA is 77.69%. The best removal rate is 87.65%. In addition, the response surface optimization of the synthesis process of MF@AA was performed. The optimal synthesis ratio was finally determined as iron content 6.5%, CMFS: 29.5%, AM: 53.9%, AMPS: 10.1%. High-efficiency magnetic heavy metal flocculant MF@AA shows excellent flocculation performance in removing Cu(II). This research provides guidance and ideas for the development of efficient and low-cost flocculation technology to remove Cu(II) in wastewater.

scholarly journals Superior Degradation Performance of Nanoporous Copper Catalysts on Methyl Orange

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 913
Author(s):  
Jinyi Wang ◽  
Sen Yang
Keyword(s):  
Activation Energy ◽  
Methyl Orange ◽  
High Efficiency ◽  
Low Cost ◽  
Degradation Process ◽  
Copper Catalysts ◽  
Reaction Rate Constant ◽  
Nanoporous Structure ◽  
Intra Particle Diffusion ◽  
Different Temperatures

The development of low-cost and high-efficiency catalysts for wastewater treatment is of great significance. Herein, nanoporous Cu/Cu2O catalysts were synthesized from MnCu, MnCuNi, and MnCuAl with similar ligament size through one-step dealloying. Meanwhile, the comparisons of three catalysts in performing methyl orange degradation were investigated. One of the catalysts possessed a degradation efficiency as high as 7.67 mg·g−1·min−1. With good linear fitting by the pseudo-first-order model, the reaction rate constant was evaluated. In order to better understand the degradation process, the adsorption behavior was considered, and it was divided into three stages based on the intra-particle diffusion model. Three different temperatures were applied to explore the activation energy of the degradation. As a photocatalytic agent, the nanoporous structure of Cu/Cu2O possessed a large surface area and it also had low activation energy, which were beneficial to the excellent degradation performance.

Preparation of Hydrated Calcium Silicate Gel and its Adsorption Properties for Cu(II)

2020 ◽  
Vol 993 ◽  
pp. 1445-1449
Author(s):  
Shi Jie Liu ◽  
Su Ping Cui ◽  
Hong Xia Guo ◽  
Ya Li Wang ◽  
Nan Li ◽  
...  
Keyword(s):  
Calcium Silicate ◽  
High Efficiency ◽  
Removal Rate ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Adsorption Method ◽  
Hydrated Calcium Silicate ◽  
Adsorption Performance ◽  
Optimum Reaction

Calcium silicate hydrate gel (CSH) was synthesized by calcium acetate and sodium silicate. The structure and morphology of CSH were characterized by X-ray diffraction analysis, Fourier transform infrared spectroscopy and Scanning electron microscopy. The adsorption performance of CSH was measured by static adsorption method. The results show that CSH has porous structure and large specific surface area, and the optimum reaction conditions is the reaction temperature of 25°C and calcium-silicon ratio of 1.2. It has the maximum adsorption capacity of more than 150 mg/g and the removal rate of more than 86% with Cu2+. And it shows the excellent adsorption performance, even when the concentration of Cu2+ is less than 200mg/L, the removal rate is above 90%. The research may provide a low-cost and high-efficiency adsorbent.

Potential of Agricultural Waste Material (Ananas cosmos) as Biosorbent for Heavy Metal Removal in Polluted Water

2020 ◽  
Vol 1010 ◽  
pp. 489-494
Author(s):  
Abdul Hafidz Yusoff ◽  
Rosmawani Mohammad ◽  
Mardawani Mohamad ◽  
Ahmad Ziad Sulaiman ◽  
Nurul Akmar Che Zaudin ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Adsorption Capacity ◽  
Metal Removal ◽  
Low Cost ◽  
Agricultural Waste ◽  
Heavy Metal Removal ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Pineapple Peel

Conventional methods to remove heavy metals from polluted water are expensive and not environmentally friendly. Therefore, this study was carried out to investigate the potential of agricultural waste such as pineapple peel (Ananas Cosmos) as low-cost absorbent to remove heavy metals from synthetic polluted water. The results showed that Cd, Cr and Pb were effectively removed by the biosorbent at 12g of pineapple peels in 100 mL solution. The optimum contact time for maximum adsorption was found to be 90 minutes, while the optimum pH for the heavy metal’s adsorption was 9. It was demonstrated that with the increase of adsorbent dosage, the percent of heavy metals removal was also increased due to the increasing adsorption capacity of the adsorbent. In addition, Langmuir model show maximum adsorption capacity of Cd is 1.91 mg/g. As conclusions, our findings show that pineapple peel has potential to remove heavy metal from polluted water.

Development of a waste-derived lignin-porphyrin bio-polymer with enhanced photoluminescence at high water fraction with wide pH range and heavy metal sensitivity investigations

2019 ◽  
Vol 21 (6) ◽  
pp. 1319-1329 ◽  
Author(s):  
Ho-Yin TSE ◽  
Shun-Cheung Cheng ◽  
Chi Shun Yeung ◽  
Chun-Yin Lau ◽  
Wing-Hei Wong ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
High Water ◽  
Water Fraction ◽  
Enhanced Photoluminescence ◽  
Metal Sensitivity ◽  
Wide Ph Range ◽  
Bio Imaging ◽  
Ph Range

A new lignin-porphyrin bio-polymer (AL-CTPP) for potential bio-imaging and heavy metals sensing.

Utilization of cross-linked chitosan/bentonite composite in the removal of methyl orange from aqueous solution

2014 ◽  
Vol 71 (2) ◽  
pp. 174-182 ◽  
Author(s):  
Ruihua Huang ◽  
Qian Liu ◽  
Lujie Zhang ◽  
Bingchao Yang
Keyword(s):  
Methyl Orange ◽  
Aqueous Solutions ◽  
Ph Value ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Wide Ph Range ◽  
Order Kinetic Model ◽  
Langmuir Isotherm Model ◽  
Ph Range ◽  
A Minor

A kind of biocomposite was prepared by the intercalation of chitosan in bentonite and the cross-linking reaction of chitosan with glutaraldehyde, which was referred to as cross-linked chitosan/bentonite (CCS/BT) composite. Adsorptive removal of methyl orange (MO) from aqueous solutions was investigated by batch method. The adsorption of MO onto CCS/BT composite was affected by the ratio of chitosan to BT and contact time. pH value had only a minor impact on MO adsorption in a wide pH range. Adsorption kinetics was mainly controlled by the pseudo-second-order kinetic model. The adsorption of MO onto CCS/BT composite followed the Langmuir isotherm model, and the maximum adsorption capacity of CCS/BT composite calculated by the Langmuir model was 224.8 mg/g. Experimental results indicated that this adsorbent had a potential for the removal of MO from aqueous solutions.

scholarly journals Sugarcane Bagasse as an Efficient Biosorbent for Methylene Blue Removal: Kinetics, Isotherms and Thermodynamics

2020 ◽  
Vol 17 (2) ◽  
pp. 526 ◽  
Author(s):  
Thaisa Caroline Andrade Siqueira ◽  
Isabella Zanette da Silva ◽  
Andressa Jenifer Rubio ◽  
Rosângela Bergamasco ◽  
Francielli Gasparotto ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Sugarcane Bagasse ◽  
Adsorption Isotherms ◽  
Low Cost ◽  
Cost Effective ◽  
Blue Dye ◽  
Maximum Adsorption Capacity ◽  
Effective Option ◽  
Pseudo Second Order ◽  
Isotherms And Thermodynamics

Adsorption in biomass has proven to be a cost-effective option for treatment of wastewater containing dyes and other pollutants, as it is a simple and low cost technique and does not require high initial investments. The present work aimed to study the adsorption of methylene blue dye (MB) using sugarcane bagasse (SCB). The biomass was characterized by scanning electron microscopy (SEM). Adsorption studies were conducted batchwise. Kinetics, adsorption isotherms, and thermodynamics were studied. The results showed that SCB presented a maximum adsorption capacity of 9.41 mg g−1 at 45 °C after 24 h of contact time. Adsorption kinetics data better fitted the pseudo-second order model, indicating a chemical process was involved. The Sips’s three-parameter isotherm model was better for adjusting the data obtained for the adsorption isotherms, indicating a heterogeneous adsorption process. The process showed to be endothermic, spontaneous, and feasible. Therefore, it was concluded that SCB presented as a potential biosorbent material for the treatment of MB-contaminated waters.

scholarly journals Adsorption of Hexavalent Chromium Using Banana Pseudostem Biochar and Its Mechanism

2018 ◽  
Vol 10 (11) ◽  
pp. 4250 ◽  
Author(s):  
Shuang Xu ◽  
Weiguang Yu ◽  
Sen Liu ◽  
Congying Xu ◽  
Jihui Li ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Pyrolysis Temperature ◽  
Low Cost ◽  
Surface Adsorption ◽  
Maximum Adsorption Capacity ◽  
X Ray ◽  
Adsorption Processes ◽  
Different Temperatures ◽  
Pseudo Second Order ◽  
Porosity Analysis

A low-cost biochar was prepared through slow pyrolysis of banana pseudostem biowaste at different temperatures, and characterized by surface area and porosity analysis, scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). It was shown that the biochar prepared at low pyrolysis temperature was rich in oxygen-containing groups on the surface. Adsorption experiments revealed that the biochar prepared at 300 °C (BB300) was the best adsorbent for Cr(VI) with 125.44 mg/g maximum adsorption capacity at pH 2 and 25 °C. All the adsorption processes were well described by pseudo-second-order and Langmuir models, indicating a monolayer chemiadsorption. Furthermore, it was demonstrated that adsorption of Cr(VI) was mainly attributed to reduction of Cr(VI) to Cr(III) followed by ion exchange and complexation with the biochar.

Mussel-inspired synthesis of polydopamine-functionalized calcium carbonate as reusable adsorbents for heavy metal ions

RSC Advances ◽  
2014 ◽  
Vol 4 (88) ◽  
pp. 47848-47852 ◽  
Author(s):  
Chengyong Li ◽  
Zhong-ji Qian ◽  
Chunxia Zhou ◽  
Weiming Su ◽  
Pengzhi Hong ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Calcium Carbonate ◽  
Chemical Modification ◽  
Heavy Metal Ions ◽  
High Efficiency ◽  
Low Cost ◽  
High Adsorption ◽  
High Adsorption Capacity ◽  
Adsorption Desorption ◽  
Multiple Adsorption

A new high-efficiency adsorbent (PDA-CaCO3) is fabricated via simple thermal calcination ostracean shells and chemical modification with dopamine. It can be easily regenerated by low-cost reagents, and exhibited high adsorption capacity after multiple adsorption–desorption cycles.

Sign in / Sign up

Export Citation Format

Share Document