scholarly journals Bankfull discharge estimation for Fishpot Creek

2020 ◽  
Vol 2 (5) ◽  
pp. 74-91
Author(s):  
Farhad Sakhaee
Keyword(s):  
Laser Scanning ◽  
Roughness Coefficient ◽  
3D Laser Scanning ◽  
Stream Channel ◽  
Cross Sectional ◽  
Bankfull Discharge ◽  
Data Points ◽  
The Cross ◽  
Sectional Shape ◽  
Discharge Estimation

Abstract: Fishpot Creek has been investigated and bankfull discharge was calculated based on the collected data points obtained from 3D laser scanning of the stream. This report consists of two major parts. One is the 3D scanning and analysis the results, other part includes sampling of both bed and bank materials. In the first part, essential parameters of roughness coefficient based on Cowan’s method were calculated as well as calculating the cross-sectional area and wetted perimeter based on the profile obtained from stream channel scanning.  Leica Scan Station HDS 3000 scanner was used to visualize the cross-sectional shape of the stream based on a high-density scan technology and finally applied to the manning’s equation to calculate the bankfull discharge. for sampling part both bed and bank materials were analyzed in lab, mechanical sieve test performed to investigate the gradation of bed and banks materials within the study area.

On the cross-sectional shape of the cellulose crystallites in the tunicate Halocynthia papillosa

1990 ◽  
Vol 48 (3) ◽  
pp. 566-567
Author(s):  
J.-F. Revol ◽  
Y. Van Daele ◽  
F. Gaill
Keyword(s):  
Contrast Imaging ◽  
Animal Kingdom ◽  
Bright Field ◽  
Field Mode ◽  
Cross Sectional ◽  
Ultrathin Sections ◽  
The Cross ◽  
Sectional Shape ◽  
Valonia Ventricosa ◽  
C Nmr

The only form of cellulose which could unequivocally be ascribed to the animal kingdom is the tunicin that occurs in the tests of the tunicates. Recently, high-resolution solid-state l3C NMR revealed that tunicin belongs to the Iβ form of cellulose as opposed to the Iα form found in Valonia and bacterial celluloses. The high perfection of the tunicin crystallites led us to study its crosssectional shape and to compare it with the shape of those in Valonia ventricosa (V.v.), the goal being to relate the cross-section of cellulose crystallites with the two allomorphs Iα and Iβ.In the present work the source of tunicin was the test of the ascidian Halocvnthia papillosa (H.p.). Diffraction contrast imaging in the bright field mode was applied on ultrathin sections of the V.v. cell wall and H.p. test with cellulose crystallites perpendicular to the plane of the sections. The electron microscope, a Philips 400T, was operated at 120 kV in a low intensity beam condition.

scholarly journals Optimization of the cross-sectional shape of the belts of trihedral lattice supports

2019 ◽  
Vol 7 (4) ◽  
pp. 5-8
Author(s):  
Linar Sabitov ◽  
Ilnar Baderddinov ◽  
Anton Chepurnenko
Keyword(s):  
Objective Function ◽  
Nonlinear Optimization ◽  
Cross Section ◽  
Optimization Methods ◽  
Cross Sectional ◽  
Maximum Value ◽  
Axial Moment ◽  
The Cross ◽  
Nonlinear Optimization Methods ◽  
Sectional Shape

The article considers the problem of optimizing the geometric parameters of the cross section of the belts of a trihedral lattice support in the shape of a pentagon. The axial moment of inertia is taken as the objective function. Relations are found between the dimensions of the pentagonal cross section at which the objective function takes the maximum value. We introduce restrictions on the constancy of the consumption of material, as well as the condition of equal stability. The solution is performed using nonlinear optimization methods in the Matlab environment.

Numerical study for the improvement of bead spreading architecture with modified nozzle geometries in additive manufacturing of polymers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Easir Arafat Papon ◽  
Anwarul Haque ◽  
Muhammad Ali Rob Sharif
Keyword(s):  
Free Surface ◽  
Numerical Model ◽  
3D Printing ◽  
Cross Section ◽  
Nozzle Exit ◽  
Cross Sectional ◽  
Content Type ◽  
The Cross ◽  
Viscous Polymer ◽  
Sectional Shape

Purpose This paper aims to develop a numerical model of bead spreading architecture of a viscous polymer in fused filament fabrication (FFF) process with different nozzle geometry. This paper also focuses on the manufacturing feasibility of the nozzles and 3D printing of the molten beads using the developed nozzles. Design/methodology/approach The flow of a highly viscous polymer from a nozzle, the melt expansion in free space and the deposition of the melt on a moving platform are captured using the FLUENT volume of fluid (VOF) method based computational fluid dynamics code. The free surface motion of the material is captured in VOF, which is governed by the hydrodynamics of the two-phase flow. The phases involved in the numerical model are liquid polymer and air. A laminar, non-Newtonian and non-isothermal flow is assumed. Under such assumptions, the spreading characteristic of the polymer is simulated with different nozzle-exit geometries. The governing equations are solved on a regular stationary grid following a transient algorithm, where the boundary between the polymer and the air is tracked by piecewise linear interface construction (PLIC) to reconstruct the free surface. The prototype nozzles were also manufactured, and the deposition of the molten beads on a flatbed was performed using a commercial 3D printer. The deposited bead cross-sections were examined through optical microscopic examination, and the cross-sectional profiles were compared with those obtained in the numerical simulations. Findings The numerical model successfully predicted the spreading characteristics and the cross-sectional shape of the extruded bead. The cross-sectional shape of the bead varied from elliptical (with circular nozzle) to trapezoidal (with square and star nozzles) where the top and bottom surfaces are significantly flattened (which is desirable to reduce the void spaces in the cross-section). The numerical model yielded a good approximation of the bead cross-section, capturing most of the geometric features of the bead with a reasonable qualitative agreement compared to the experiment. The quantitative comparison of the cross-sectional profiles against experimental observation also indicated a favorable agreement. The significant improvement observed in the bead cross-section with the square and star nozzles is the flattening of the surfaces. Originality/value The developed numerical algorithm attempts to address the fundamental challenge of voids and bonding in the FFF process. It presents a new approach to increase the inter-bead bonding and reduce the inter-bead voids in 3D printing of polymers by modifying the bead cross-sectional shape through the modification of nozzle exit-geometry. The change in bead cross-sectional shape from elliptical (circular) to trapezoidal (square and star) cross-section is supposed to increase the contact surface area and inter-bead bonding while in contact with adjacent beads.

scholarly journals Discharge Estimation Using Tsallis and Shannon Entropy Theory in Natural Channels

Water ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1786
Author(s):  
Jitendra Kumar Vyas ◽  
Muthiah Perumal ◽  
Tommaso Moramarco
Keyword(s):  
Flow Velocity ◽  
Surface Flow ◽  
Tsallis Entropy ◽  
Accurate Estimation ◽  
Mean Flow ◽  
Flow Area ◽  
Cross Sectional ◽  
The Cross ◽  
Discharge Estimation ◽  
Mean Flow Velocity

Streamflow measurements during high floods is a challenge for which the World Meteorological Organization fosters the development of innovative technologies for achieving an accurate estimation of the discharge. The use of non-contact sensors for monitoring surface flow velocities is of interest to turn these observed values into a cross-sectional mean flow velocity, and subsequently, into discharge if bathymetry is given. In this context, several techniques are available for the estimation of mean flow velocity, starting from observed surface velocities. Among them, the entropy-based methodology for river discharge assessment is often applied by leveraging the theoretical entropic principles of Shannon and Tsallis, both of which link the maximum flow velocity measured at a vertical of the flow area, named the y-axis, and the cross-sectional mean flow velocity at a river site. This study investigates the performance of the two different entropic approaches in estimating the mean flow velocity, starting from the maximum surface flow velocity sampled at the y-axis. A velocity dataset consisting of 70 events of measurements collected at two gauged stations with different geometric and hydraulic characteristics on the Po and Tiber Rivers in Italy was used for the analysis. The comparative evaluation of the velocity distribution observed at the y-axis of all 70 events of measurement was closely reproduced using both the Shannon and Tsallis entropy approaches. Accurate values in terms of the cross-sectional mean flow velocity and discharge were obtained with average errors not exceeding 10%, demonstrating that the Shannon and Tsallis entropy concepts were equally efficient for discharge estimation in any flow conditions.

scholarly journals Analytical Model of a Multi-Step Straightening Process for Linear Guideways Considering Neutral Axis Deviation

Symmetry ◽  
2018 ◽  
Vol 10 (8) ◽  
pp. 316 ◽  
Author(s):  
Yongquan Zhang ◽  
Hong Lu ◽  
He Ling ◽  
Yang Lian ◽  
Mingtian Ma
Keyword(s):  
Analytical Model ◽  
Cross Section ◽  
Predictive Accuracy ◽  
Neutral Axis ◽  
Longitudinal Stress ◽  
Linear Superposition ◽  
Element Analysis ◽  
Cross Sectional ◽  
The Cross ◽  
Sectional Shape

The cross-sectional shape of a linear guideway has been processed before the straightening process. The cross-section features influence not only the position of the neutral axis, but also the applied and residual stresses along the longitudinal direction, especially in a multi-step straightening process. This paper aims to present an analytical model based on elasto-plastic theory and three-point reverse bending theory to predict straightening stroke and longitudinal stress distribution during the multi-step straightening process of linear guideways. The deviation of the neutral axis is first analyzed considering the asymmetrical features of the cross-section. Owing to the cyclic loading during the multi-step straightening process, the longitudinal stress curves are then calculated using the linear superposition of stresses. Based on the cross-section features and the superposition of stresses, the bending moment is corrected to improve the predictive accuracy of the multi-step straightening process. Finite element analysis, as well as straightening experiments, have been performed to verify the applicability of the analytical model. The proposed approach can be implemented in the multi-step straightening process of linear guideways with similar cross-sectional shape to improve the straightening accuracy.

Erythrocyte Sedimentation Rates in Inclined Vessels

1973 ◽  
Vol 51 (9) ◽  
pp. 685-690 ◽  
Author(s):  
R. N. O'Brien ◽  
M. B. Hocking ◽  
P. McOrmond ◽  
K. R. Thornton
Keyword(s):  
Cross Section ◽  
Sedimentation Rates ◽  
Settling Rate ◽  
Cross Sectional ◽  
Erythrocyte Sedimentation ◽  
The Cross ◽  
Sectional Shape ◽  
Erythrocyte Sedimentation Rates ◽  
Test Rack ◽  
Settling Rates

The rates of erythrocyte settling have been investigated in round and square cross-section tubes, vertically; and at nine different angles; and with the square tubes flat and on edge, to a minimum of 15° from the horizontal. Apparent settling rates increased as the angle from the horizontal decreased. Real settling rates (vertical settling rates) increased sharply on decreasing the angle from the horizontal, to a maximum at about 60°, and then decreased less abruptly for the shallower angles. The cross-sectional shape of the tube did not significantly affect the settling rates of erythrocytes. Settling in inclined tubes proceeds fast enough to permit clinical erythrocyte settling rate (E.S.R.) tests to be carried out in 10 min in place of the usual 60 min. If the standard E.S.R. test rack deviates as little as 5° from the vertical it can cause the observed settling rates to double relative to readings obtained on a vertical rack.

The Use of a Laser Micrometer System to Determine the Cross-Sectional Shape and Area of Ligaments: A Comparative Study With Two Existing Methods

1990 ◽  
Vol 112 (4) ◽  
pp. 426-431 ◽  
Author(s):  
Savio L.-Y. Woo ◽  
Michael I. Danto ◽  
Karen J. Ohland ◽  
Thay Q. Lee ◽  
Peter O. Newton
Keyword(s):  
Constant Pressure ◽  
Cruciate Ligament ◽  
Applied Pressure ◽  
Cross Sectional Area ◽  
Sectional Area ◽  
Cross Sectional ◽  
Proximal Site ◽  
Pressure Area ◽  
The Cross ◽  
Sectional Shape

Determination of the tensile stresses in ligaments and tendons during uniaxial loading depends on accurate measurement of the cross-sectional area. In this study, a laser micrometer system was employed to evaluate the cross-sectional shape and area of the medial collateral ligament (MCL) at three locations and anterior cruciate ligament (ACL). In a New Zealand White (NZW) rabbit, morphologic sections of the ligaments were made to verify the cross-sectional shape reconstructed by the laser micrometer system. The areas obtained by the laser micrometer system from ten additional NZW rabbits were compared with those obtained by two other methods commonly used to measure the cross-sectional area of ligaments and tendons: one method uses digital calipers and the other a constant pressure (0.12 MPa) area micrometer. For the MCL, the digital calipers yielded results very similar to those of the laser micrometer, but the constant pressure area micrometer yielded values 20 percent lower. The area measured at the proximal site of the MCL was 13 percent greater than the area measured at the joint line and distal line. For the ACL, the values obtained by the digital calipers and constant pressure area micrometer were 16 and 20 percent lower, respectively. Because of the irregular shape exhibited by the rabbit ACL, the digital calipers could not accurately measure the crosssectional area. The constant pressure area micrometer yielded lower values for the cross-sectional area of both the MCL and ACL, presumably due to the applied pressure which caused changes in both the cross-sectional shape and area.

Sign in / Sign up

Export Citation Format

Share Document