scholarly journals Preparation of Nano Ink Using Cobalt Ferrite and Barium Titanate for Printed Electronic Devices

2020 ◽  
Vol 3 (10) ◽  
pp. 132-135
Author(s):  
Emy Rose Peter ◽  
Jismon Sebastian ◽  
Swapna S. Nair
Keyword(s):  
Barium Titanate ◽  
Cobalt Ferrite ◽  
Diffraction Method ◽  
Band Gap Energy ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Pure Cobalt ◽  
Uv Visible

Lead in our body is toxic and hazardous. Here leadfree Cobalt ferrite and Barium Titanate inks have been prepared and fabricated. The prepared inks remained stable without agglomeration or condensation during preservation. Cobalt Ferrite and Barium Titanate Nano inks have been characterized using X-ray diffraction method and UV Visible Spectroscopy. By the analysis of X-ray diffraction (XRD), the resultant inks were confirmed to be of pure Cobalt Ferrite and Barium Titanate powders with cubic structure and tetragonal structure respectively. Lattice parameters and grain size have been determined by X-ray diffraction method. UV Visible Spectroscopy analysis has been done to obtain the band gap energy of the prepared inks. The preparation and characterization of Cobalt Ferrite and Barium Titanate Nano inks are comprehensively demonstrated in this paper.

In Situ Polymerization and Characterization of Poly(ε-caprolactone)/Layered Double Hydroxide Nanocomposites

2012 ◽  
Vol 557-559 ◽  
pp. 371-374
Author(s):  
Lian Liu ◽  
Teng Yu ◽  
Pei Wang ◽  
Guang Shuo Wang
Keyword(s):  
Layered Double Hydroxide ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Visible ◽  
Absorbance Peak ◽  
Double Hydroxide

Nanocomposites of poly(ε-caprolactone) (PCL) and layered double hydroxide (LDH) were prepared by in situ polymerization at low LDHs loadings in this work. The resultants were characterized by FTIR spectroscopy, X-ray diffraction (XRD), differential scanning calorimeter (DSC) and UV-visible spectroscopy (UV-vis). FTIR showed that the PCL/LDHs nanocomposites were prepared successfully by in situ polymerization and XRD spectra showed that the crystal structure did not change greatly in the presence of LDHS. DSC results confirmed that LDHs could act as nucleating agents. UV-vis spectra showed that LDHs had stronger absorbance peak than LDH. Moreover, the PCL/LDHs nanocomposites had strong anti-ultraviolet effect by introduction of LDHs into polymer matrix.

scholarly journals Synthesis and Characterization of Dodecylbenzene Sulfonic Acid doped Tetraaniline via Emulsion Polymerization

2012 ◽  
Vol 9 (3) ◽  
pp. 1342-1346 ◽  
Author(s):  
K. Basavaiah ◽  
K. Tirumala Rao ◽  
A. V. Prasada Rao
Keyword(s):  
Sulfonic Acid ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Molar Ratios ◽  
Uv Visible ◽  
Dodecylbenzene Sulfonic Acid ◽  
Diffraction Patterns ◽  
Thermal Stability Of

In this work, we report preparation and characterization of dodecylbenzene sulfonic acid (DBSA) doped tetraaniline via micelles assisted method using ammonium per sulphate (APS) as an oxidant. Here, DBSA act as dopant as well as template for tetraaniline nanostructures. The synthesized DBSA doped tetraaniline have been well characterized by X-ray diffraction patterns, Fourier transform infrared spectroscopy, UV-Visible spectroscopy, Scanning electron microscopy and thermogravimetry. The morphologies of tetraaniline were found to be dependent on molar ratios of N-phenyl-1, 4-phenylenediamine to DBSA. The spectroscopic data indicated that DBSA doped tetraaniline. Thermogravimetry studies revealed that the DBSA doping improved the thermal stability of tetraaniline.

scholarly journals Synthesis and characterization of erbium trioxide nanoparticles as photocatalyzers for degradation of methyl orange dye

2019 ◽  
Vol 12 (1) ◽  
pp. 15-21 ◽  
Author(s):  
Rifat Mohammed Dakhil ◽  
Tayser Sumer Gaaz ◽  
Ahmed Al-Amiery ◽  
Mohd S. Takriff ◽  
Abdul Amir H. Kadhum
Keyword(s):  
Methyl Orange ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Visible ◽  
Methyl Orange Dye ◽  
Microscopy Techniques ◽  
Degradation Of Methyl Orange

Abstract. The present work focuses on the photocatalytic degradation of methyl orange (MO) on erbium trioxide nanoparticles (Er2O3 NPs). In this study, Er2O3 nanoparticles were synthesized and fully characterized via various techniques, including X-ray diffraction, UV–visible spectroscopy and scanning electron microscopy techniques. The results revealed that the photocatalytic activity of the prepared Er2O3 NPs was manifested in MO photodegradation. The optimum efficiency obtained was 16 %.

Synthesis and characterization of 1,4-diazophenylenebridged Cu-phthalocyanine polymer

e-Polymers ◽  
2004 ◽  
Vol 4 (1) ◽  
Author(s):  
Cemil Alkan ◽  
Leyla Aras ◽  
Güngör Gündüz
Keyword(s):  
Electrical Conductivity ◽  
Diazonium Salt ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Uv Visible ◽  
Soluble Part

Abstract A novel type of phthalocyanine polymer, 1,4-diazophenylene-bridged Cuphthalocyanine, was prepared from the diazonium salt of diaminobenzene and Cu(II) 1,8,15,22-tetraaminophthalocyanine. The polymer is partially soluble in tetrahydrofuran, dichloromethane, and dimethylformamide. Characterization of the polymer was performed by IR and UV-visible spectroscopy, X-ray diffraction, ash analysis, viscometry, differential scanning calorimetry and thermogravimetric analysis. The molecular weight of the soluble part of the polymer was determined by ebullioscopy. Electrical conductivity of the polymer and its doped samples were determined by the 4-probe technique. It was found that the electrical conductivity increased up to 10-4 S/cm after doping. The redox behaviour of the polymer was investigated utilizing cyclic voltammetry.

scholarly journals Microwave-Assisted Synthesis and Characterization of [Rh2(OAc)4(L)2] Paddlewheel Complexes: A Joint Experimental and Computational Study

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Oscar F. Gonzalez-Belman ◽  
Yazmín Varela ◽  
Marcos Flores-Álamo ◽  
Kazimierz Wrobel ◽  
Silvia Gutierrez-Granados ◽  
...  
Keyword(s):  
Computational Study ◽  
Microwave Assisted Synthesis ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
Experimental Conditions ◽  
X Ray ◽  
Paddlewheel Complexes ◽  
Uv Visible ◽  
Insight Into

The synthesis of four rhodium(II) paddlewheel complexes bearing axial aromatic amines and coumarin ligands, with formula [Rh2(OAc)4(L)2] (L = NH2Mesityl (1), NH2Dip (2), NH2Couma (3), coumarin (4)), prompted by microwave irradiation, was carried out successfully. All of the complexes were characterized by the melting point, elemental analysis, NMR, IR, and UV/Visible spectroscopy. Additionally, the structure of complexes 1-2 and 4 was corroborated by single-crystal X-ray diffraction. Cyclic voltammetry, ESI-MS, and tandem MS analyses were carried out in compound 1 for gaining further insight into its stability. Finally, a DFT study shows that complexes 1–4 are the thermodynamic products, having as intermediates complexes 1′–4′ which, under our experimental conditions, cannot be isolated.

Characterization of New Nonstoichiometric Ferroelectric (Li0.95Cu0.15)Ta0.76Nb0.19O3 and Comparative Study With (Li0.95Cu0.15)Ta0.57Nb0.38O3 as Photocatalysts in Microbial Fuel Cells

2018 ◽  
Vol 16 (2) ◽  
Author(s):  
S. Louki ◽  
N. Touach ◽  
A. Benzaouak ◽  
V. M. Ortiz-Martínez ◽  
M. J. Salar-García ◽  
...  
Keyword(s):  
Power Density ◽  
Microbial Fuel Cells ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Ferroelectric Material ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Uv Visible

This work investigates the photocatalytic activity of new ferroelectric material with formula (Li0.95Cu0.15)Ta0.76Nb0.19O3 (LT76) in a single chamber microbial fuel cell (MFC) and compares its performance with the similar photocatalyst (Li0.95Cu0.15)Ta0.57Nb0.38O3 (LT57). The photocatalysts LT76 and LT57 were synthesized by ceramic route under the same conditions, with the same starting materials. The ratio Ta/Nb was fixed at 4.0 and 1.5 for LT76 and LT57, respectively. These phases were characterized by different techniques including X-ray diffraction (XRD), transmission electronic microscopy (TEM), particle size distribution (PSD), differential scanning calorimetry (DSC), and ultraviolet (UV)–visible (Vis). The new photocatalyst LT76 presents specific surface area of 0.791 m2/g and Curie temperature of 1197 °C. The photocatalytic efficiency of this material is assessed in terms of wastewater treatment and electricity generation by power density and removal rate of chemical oxygen demand (COD) in the presence of a light source. The values of maximum power density and COD removal were 19.77 mW/m3 and 93%, respectively, for LT76.

scholarly journals Bio Synthesis and Characterization of Silver Nanoparticles Using Lagenaria siceraria Leaf Extract and their Antibacterial Activity

2014 ◽  
Vol 38 ◽  
pp. 35-45 ◽  
Author(s):  
B. Anandh ◽  
A. Muthuvel ◽  
M. Emayavaramban
Keyword(s):  
Silver Nanoparticles ◽  
Leaf Extract ◽  
Face Centered Cubic ◽  
Lagenaria Siceraria ◽  
Human Pathogens ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Ft Ir ◽  
Uv Visible

The present investigation demonstrates the formation of silver nanoparticles by the reduction of the aqueous silver metal ions during exposure to the Lagenaria siceraria leaf extract. The synthesized AgNPs have characterized by UV-visible spectroscopy, X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) techniques. AgNPs formation has screened by UV-visible spectroscopy through colour conversion due to surface plasma resonance band at 427 nm. X-ray diffraction (XRD) confirmed that the resulting AgNPs are highly crystalline and the structure is face centered cubic (fcc). FT-IR spectrum indicates the presence of different functional groups present in the biomolecules capping the nanoparticles. Further, inhibitory activity of AgNPs and leaf extract were tested against human pathogens like gram-pastive (Staphylococcus aureus, Bacillus subtilis), gram-negative (Escherichia coli and Pseudomonas aeruginosa). The results indicated that the AgNPs showed moderate inhibitory actions against human pathogens than Lagenaria siceraria leaf extract, demonstrating its antimicrobial value against pathogenic diseases

scholarly journals Synthesis, Crystal Structure, and Properties of a Zn(II) Coordination Polymer Based on a Difunctional Ligand Containing Triazolyl and Carboxyl Groups

Crystals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 424 ◽  
Author(s):  
Jia-Le Li ◽  
Wei-Dong Li ◽  
Zi-Wei He ◽  
Shuai-Shuai Han ◽  
Shui-Sheng Chen
Keyword(s):  
Coordination Polymer ◽  
Weak Interactions ◽  
Layer Structure ◽  
Three Dimensional ◽  
Stacking Interactions ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Visible

A new compound, namely, [Zn(L)2]n (1) was obtained by the reaction of 2-methyl-4-(4H-1,2,4-triazol-4-yl) benzoic acid (HL) with ZnSO4·7H2O, and the compound was characterized by single-crystal X-ray diffraction, infrared spectroscopy, elemental analysis, powder X-ray diffraction (PXRD), and thermogravimetric analysis. The linear HL ligands were deprotonated to be L− anions and act as two-connectors to link Zn2+ to form a two-dimensional (2D) lay structure with (4, 4) topology. The large vacancy of 2D framework allows another layer structure to interpenetrate, resulting in the formation of 2D + 2D → 2D parallel interpenetration in 1. The weak interactions, such as hydrogen bonding and π–π stacking interactions, connect the adjacent 2D layers into a three-dimensional (3D) coordination polymer. The solid-state UV-visible spectroscopy and luminescent property have also been studied.

Study on integration of aluminum-doped zinc oxide (AZO) thin films with graphene oxide (GO)

2018 ◽  
Vol 32 (19) ◽  
pp. 1840044
Author(s):  
Aditya Dalal ◽  
Animesh Mandal ◽  
Shubhada Adhi ◽  
Kiran Adhi
Keyword(s):  
Thin Films ◽  
Raman Spectroscopy ◽  
Graphene Oxide ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Aluminum Doped Zinc Oxide ◽  
Uv Visible

Aluminum (0.5 at.%)-doped ZnO (AZO) thin films were deposited by pulsed laser deposition technique (PLD) in oxygen ambient of 10[Formula: see text] Torr. The deposited thin films were characterized by x-ray diffraction (XRD), photoluminescence (PL), Raman spectroscopy and uv–visible spectroscopy (UV–vis). Next, graphene oxide (GO) was synthesized by Hummers method and was characterized by XRD, UV–vis spectroscopy, Raman spectroscopy and transmission electron microscopy (TEM). Thereafter, GO solution was drop-casted on AZO thin films. These films were then characterized by Raman Spectroscopy, UV–vis spectroscopy and PL. Attempt is being made to comprehend the modifications in properties brought about by integration.

Sign in / Sign up

Export Citation Format

Share Document