scholarly journals Effect of the Fiber Orientation Relatively to the Plasma Flow Direction in the Ablation Process of a Carbon-Phenolic Composite

2015 ◽  
Vol 7 (1) ◽  
pp. 43-52 ◽  
Author(s):  
Sonia Fonseca Costa e Silva ◽  
Humberto Araujo Machado ◽  
Edison Bittencourt
2007 ◽  
Vol 25 (1) ◽  
pp. 117-144 ◽  
Author(s):  
S. Simon ◽  
A. Boesswetter ◽  
T. Bagdonat ◽  
U. Motschmann ◽  
J. Schuele

Abstract. The interaction between Titan's ionosphere and the Saturnian magnetospheric plasma flow has been studied by means of a three-dimensional (3-D) hybrid simulation code. In the hybrid model, the electrons form a mass-less, charge-neutralizing fluid, whereas a completely kinetic approach is retained to describe ion dynamics. The model includes up to three ionospheric and two magnetospheric ion species. The interaction gives rise to a pronounced magnetic draping pattern and an ionospheric tail that is highly asymmetric with respect to the direction of the convective electric field. Due to the dependence of the ion gyroradii on the ion mass, ions of different masses become spatially dispersed in the tail region. Therefore, Titan's ionospheric tail may be considered a mass-spectrometer, allowing to distinguish between ion species of different masses. The kinetic nature of this effect is emphasized by comparing the simulation with the results obtained from a simple analytical test-particle model of the pick-up process. Besides, the results clearly illustrate the necessity of taking into account the multi-species nature of the magnetospheric plasma flow in the vicinity of Titan. On the one hand, heavy magnetospheric particles, such as atomic Nitrogen or Oxygen, experience only a slight modification of their flow pattern. On the other hand, light ionospheric ions, e.g. atomic Hydrogen, are clearly deflected around the obstacle, yielding a widening of the magnetic draping pattern perpendicular to the flow direction. The simulation results clearly indicate that the nature of this interaction process, especially the formation of sharply pronounced plasma boundaries in the vicinity of Titan, is extremely sensitive to both the temperature of the magnetospheric ions and the orientation of Titan's dayside ionosphere with respect to the corotating magnetospheric plasma flow.


2018 ◽  
Vol 37 (14) ◽  
pp. 945-959 ◽  
Author(s):  
MC Quintana ◽  
MP Frontini

The present study aims to experimentally validate numerical simulation of fiber orientation distribution performed by molding simulation software Moldex3D in a double-gated injection-molded glass fiber-filled (40 wt%) polypropylene box, by making a detailed comparison of predicted and experimentally measured fiber orientation distribution data. The modeling approach evaluated in this work consists in the implementation of the Folgar–Tucker rotary diffusion model with the invariant-based optimal fitting closure approximation for the fourth-order orientation tensor. The specimen used has a weld line in the center and sharp corners. This investigation characterizes in detail the development of the through-thickness layered structure at distinctive locations of the specimen. The sensitivity of fiber orientation distribution and the layered structure to changes upon injection time and melt temperature is also evaluated. The boxes display the typical layered laminate structure, with fibers aligned in the main flow direction near the walls (shell layer) and less oriented in the middle plane (core layer). The boxes injected at the lowest melt temperature display an additional skin layer. Unfortunately, simulation fails in predicting the five layers structure developed under these latter conditions. The grade of fiber orientation is deemed to be independent of process parameters but not the layered structure.


Polymers ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 24
Author(s):  
Chao-Tsai Huang ◽  
Xuan-Wei Chen ◽  
Wei-Wen Fu

In recent years, due to the rapid development of industrial lightweight technology, composite materials based on fiber reinforced plastics (FRP) have been widely used in the industry. However, the environmental impact of the FRPs is higher each year. To overcome this impact, co-injection molding could be one of the good solutions. But how to make the suitable control on the skin/core ratio and how to manage the glass fiber orientation features are still significant challenges. In this study, we have applied both computer-aided engineering (CAE) simulation and experimental methods to investigate the fiber feature in a co-injection system. Specifically, the fiber orientation distributions and their influence on the tensile properties for the single-shot and co-injection molding have been discovered. Results show that based on the 60:40 of skin/core ratio and same materials, the tensile properties of the co-injection system, including tensile stress and modulus, are a little weaker than that of the single-shot system. This is due to the overall fiber orientation tensor at flow direction (A11) of the co-injection system being lower than that of the single-shot system. Moreover, to discover and verify the influence of the fiber orientation features, the fiber orientation distributions (FOD) of both the co-injection and single-shot systems have been observed using micro-computerized tomography (μ-CT) technology to scan the internal structures. The scanned images were further utilizing Avizo software to perform image analyses to rebuild the fiber structure. Specifically, the fiber orientation tensor at flow direction (A11) of the co-injection system is about 89% of that of the single-shot system in the testing conditions. This is because the co-injection part has lower tensile properties. Furthermore, the difference of the fiber orientation tensor at flow direction (A11) between the co-injection and the single-shot systems is further verified based on the fiber morphology of the μ-CT scanned image. The observed result is consistent with that of the FOD estimation using μ-CT scan plus image analysis.


2000 ◽  
Vol 18 (8) ◽  
pp. 918-926 ◽  
Author(s):  
E. D. Tereshchenko ◽  
B. Z. Khudukon ◽  
M. O. Kozlova ◽  
O. V. Evstafiev ◽  
T. Nygrén ◽  
...  

Abstract. Results are shown from an experimental campaign where satellite scintillation was observed at three sites at high latitudes and, simultaneously, the F region plasma flow was measured by the nearby EISCAT incoherent scatter radar. The anisotropy parameters of field-aligned irregularities are determined from amplitude scintillation using a method based on the variance of the relative logarithmic amplitude. The orientation of the anisotropy in a plane perpendicular to the geomagnetic field is compared with the direction of F region plasma flow. The results indicate that in most cases a good agreement between the two directions is obtained.Key words: Ionosphere (auroral ionosphere; ionospheric irregularities)


Author(s):  
Han-Xiong Huang ◽  
Can Yang ◽  
Kun Li

Four processing parameters, including compression force, compression time, compression distance, and delay time, were investigated in terms of their effects on the fiber orientation in injection-compression molded (ICM) short-fiber-reinforced polypropylene parts. The results reveal that the fiber orientation pattern in ICM parts is different from that in conventional injection molded parts. Compression force plays an important role in determining the fiber orientation, whereas the effect of compression time can be neglected. Moreover, the fiber orientation changes obviously in the width direction, with most fibers arranging orderly in the flow direction at positions near the mold cavity wall.


2020 ◽  
Vol 10 (16) ◽  
pp. 5565
Author(s):  
Pruthvi K. Sridhara ◽  
Fabiola Vilaseca

Cellulose is being considered as a suitable renewable reinforcement for materials production. In particular, cellulose based composites are attracting global interest for their unique and intrinsic properties such as strength to weight ratio, dimensional stability and low thermal expansion and contraction. This article investigates the preparation of cellulose pulp fibers with polyamide-6 (PA6) polymer and the effect of fiber orientation within the matrix on the final properties of the biocomposite. Cellulose pulp fibers were melt compounded with PA6 using a thermo-kinetic mixer. Different formulations were prepared and the compounds were manufactured into test samples by injection molding. Mechanical characterization revealed that elastic modulus and the flexural properties increased linearly with the fiber composition. The effect of fiber orientation was examined from square samples out of which individual specimens were cut at different directions with respect to the flow direction. The contributions related to fiber content and effect of fiber orientation on the tensile properties assessed lent positively towards parallel oriented samples (0°) with respect to flow direction. Furthermore, the cellulose network within the biocomposite revealed the superior interfacial properties between the cellulose and PA6 matrix when observed under a scanning electron microscope.


2014 ◽  
Vol 668-669 ◽  
pp. 60-63
Author(s):  
Hong He ◽  
Xiong Bing Chen

Understanding rules of the distribution of fiber is important to control the mechanical properties of composite material performance. Fiber orientation in dumbbell-shaped injection cavity is different from that in regular cuboids because of its complex shape. Fiber orientation equation, Fokker - Planck equation was solved by the finite volume method and the errors brought by approximate method were avoided. The calculation results verified demonstrated that the shape of injection cavity affected the fiber orientation. In the flow direction, fiber of the shrinkage zone oriented along the flow direction and of the dilation zone oriented along tensile direction which is vertical to the flow. In cavity thickness direction, fiber orientation was layered.


1998 ◽  
Vol 16 (4) ◽  
pp. 425-440 ◽  
Author(s):  
H. Lühr ◽  
A. Aylward ◽  
S. C. Bucher ◽  
A. Pajunpää ◽  
K. Pajunpää ◽  
...  

Abstract. We present the ground signatures of dynamic substorm features with particular emphasis on the event interpretation capabilities provided by the IMAGE magnetometer network. This array covers the high latitudes from the sub-auroral to the cusp/cleft region. An isolated substorm on 11 Oct. 1993 during the late evening hours exhibited many of well-known features such as the Harang discontinuity, westward travelling surge and poleward leap, but also discrete auroral forms, known as auroral streamers, appeared propagating westward along the centre of the electrojet. Besides the magnetic field measurements, there were auroral observations and plasma flow and conductivity measurements obtained by EISCAT. The data of all three sets of instruments are consistent with the notion of upward field-aligned currents associated with the moving auroral patches. A detailed analysis of the electrodynamic parameters in the ionosphere, however, reveals that they do not agree with the expectations resulting from commonly used simplifying approximations. For example, the westward moving auroral streamers which are associated with field-aligned current filaments, are not collocated with the centres of equivalent current vortices. Furthermore, there is a clear discrepancy between the measured plasma flow direction and the obtained equivalent current direction. All this suggests that steep conductivity gradients are associated with the transient auroral forms. Also self-induction effects in the ionosphere may play a role for the orientation of the plasma flows. This study stresses the importance of multi-instrument observation for a reliable interpretation of dynamic auroral processes.Keywords. Ionosphere (Auroral ionosphere; Electric fields and currents; Ionosphere-magnetosphere interactions).


Sign in / Sign up

Export Citation Format

Share Document