scholarly journals Forensic Engineering Analysis of Dynamic Forces Created by Pedestrians Impacting Plate Glass at Different Speeds

2015 ◽  
Vol 32 (1) ◽  
Author(s):  
Michael Kravitz
Keyword(s):  
Impact Load ◽  
Building Code ◽  
Engineering Analysis ◽  
Glass Panel ◽  
Impact Speed ◽  
Dynamic Forces ◽  
Exit Door ◽  
Forensic Engineering ◽  
Pedestrian Impact ◽  
The Impact

This paper examines the effect of a pedestrian inadvertently impacting a glass panel adjacent to a glass exit door. The glass panel was full length and unmarked, violating the local building code and building commissioner directives. The defense argued that the old building code, to which the college building was constructed, was “grandfathered” and there was no violation. Initial witness and plaintiff statements indicated that the plaintiff was running when he struck the panel, which shattered and caused the plaintiff to incur injuries. The plaintiff testified later, in deposition, that he was walking when he struck the glass. The court needed to establish liability percentage, which is common in civil cases, and it was necessary to determine at what pedestrian impact speed the glass panel would break. The analysis used Timoshenko’s theory of vibration plates, Roark’s stress strain formulas, ergonomics, and human factors to estimate the impact load and stresses on the glass panel that caused failure.

scholarly journals Forensic Engineering Analysis Of safety Shooting Glasses subject To Ballistic Impact

2011 ◽  
Vol 28 (2) ◽  
Author(s):  
David Danaher
Keyword(s):  
Impact Resistance ◽  
National Standards ◽  
Engineering Analysis ◽  
Minimum Level ◽  
Absorbed Energy ◽  
Voluntary Standards ◽  
Minimum Requirements ◽  
Forensic Engineering ◽  
The Impact ◽  
Current Standards

Currently There Are Voluntary Standards In Place That Outline The Impact Resistance Of Safety Glasses.  although The Standards Set Forth By The American National Standards Institute (Ansi) Outline Testing that Can Be Used To Calculate A Minimum Level Of Energy Which The Lens Should Absorb, Independent Testing has Shown That The Performance Of Modern Safety Glasses Exceed The Minimum Requirements Of The absorbed Energy. This Paper Will Show The Level Of Energy Which A Random Sample Of Safety Glasses Can withstand And Compare The Results To The Current Standards.

Asteroid and Comet Impact Speeds upon Mars: Significance for Panspermia and the Supply of Organics

1997 ◽  
Vol 161 ◽  
pp. 197-201 ◽  
Author(s):  
Duncan Steel
Keyword(s):  
Probability Distributions ◽  
Regions Of Interest ◽  
Significant Fraction ◽  
Organic Chemicals ◽  
Impact Speed ◽  
The Mean ◽  
The Impact

AbstractWhilst lithopanspermia depends upon massive impacts occurring at a speed above some limit, the intact delivery of organic chemicals or other volatiles to a planet requires the impact speed to be below some other limit such that a significant fraction of that material escapes destruction. Thus the two opposite ends of the impact speed distributions are the regions of interest in the bioastronomical context, whereas much modelling work on impacts delivers, or makes use of, only the mean speed. Here the probability distributions of impact speeds upon Mars are calculated for (i) the orbital distribution of known asteroids; and (ii) the expected distribution of near-parabolic cometary orbits. It is found that cometary impacts are far more likely to eject rocks from Mars (over 99 percent of the cometary impacts are at speeds above 20 km/sec, but at most 5 percent of the asteroidal impacts); paradoxically, the objects impacting at speeds low enough to make organic/volatile survival possible (the asteroids) are those which are depleted in such species.

Impact Load Buffering Method Based on Stress Wave Attenuation Principle

2019 ◽  
Vol 11 (02) ◽  
pp. 1950019 ◽  
Author(s):  
Lin Gan ◽  
He Zhang ◽  
Cheng Zhou ◽  
Lin Liu
Keyword(s):  
Stress Wave ◽  
Wave Attenuation ◽  
Impact Load ◽  
Dynamics Simulation ◽  
Scanning System ◽  
Isolation Method ◽  
Element Analysis ◽  
System A ◽  
High Emission ◽  
The Impact

Rotating scanning motor is the important component of synchronous scanning laser fuze. High emission overload environment in the conventional ammunition has a serious impact on the reliability of the motor. Based on the theory that the buffer pad can attenuate the impact stress wave, a new motor buffering Isolation Method is proposed. The dynamical model of the new buffering isolation structure is established by ANSYS infinite element analysis software to do the nonlinear impact dynamics simulation of rotating scanning motor. The effectiveness of Buffering Isolation using different materials is comparatively analyzed. Finally, the Macht hammer impact experiment is done, the results show that in the experience of the 70,000[Formula: see text]g impact acceleration, the new buffering Isolation method can reduce the impact load about 15 times, which can effectively alleviate the plastic deformation of rotational scanning motor and improve the reliability of synchronization scanning system. A new method and theoretical basis of anti-high overload research for Laser Fuze is presented.

scholarly journals A Rational Numerical Method for Simulation of Drop-Impact Dynamics of Oleo-Pneumatic Landing Gear

2021 ◽  
Vol 11 (9) ◽  
pp. 4136
Author(s):  
Rosario Pecora
Keyword(s):  
Numerical Method ◽  
Initial Conditions ◽  
Impact Load ◽  
Numerical Models ◽  
Landing Gear ◽  
Design Stage ◽  
Impact Dynamics ◽  
State Variables ◽  
Adopted Model ◽  
The Impact

Oleo-pneumatic landing gear is a complex mechanical system conceived to efficiently absorb and dissipate an aircraft’s kinetic energy at touchdown, thus reducing the impact load and acceleration transmitted to the airframe. Due to its significant influence on ground loads, this system is generally designed in parallel with the main structural components of the aircraft, such as the fuselage and wings. Robust numerical models for simulating landing gear impact dynamics are essential from the preliminary design stage in order to properly assess aircraft configuration and structural arrangements. Finite element (FE) analysis is a viable solution for supporting the design. However, regarding the oleo-pneumatic struts, FE-based simulation may become unpractical, since detailed models are required to obtain reliable results. Moreover, FE models could not be very versatile for accommodating the many design updates that usually occur at the beginning of the landing gear project or during the layout optimization process. In this work, a numerical method for simulating oleo-pneumatic landing gear drop dynamics is presented. To effectively support both the preliminary and advanced design of landing gear units, the proposed simulation approach rationally balances the level of sophistication of the adopted model with the need for accurate results. Although based on a formulation assuming only four state variables for the description of landing gear dynamics, the approach successfully accounts for all the relevant forces that arise during the drop and their influence on landing gear motion. A set of intercommunicating routines was implemented in MATLAB® environment to integrate the dynamic impact equations, starting from user-defined initial conditions and general parameters related to the geometric and structural configuration of the landing gear. The tool was then used to simulate a drop test of a reference landing gear, and the obtained results were successfully validated against available experimental data.

scholarly journals Analysis on Force Transmission Characteristics of Two-Legged Shield Support under Impact Loading

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Qing-liang Zeng ◽  
Zhao-sheng Meng ◽  
Li-rong Wan ◽  
Cheng-long Wang
Keyword(s):  
Structural Design ◽  
Load Transfer ◽  
Impact Load ◽  
Force Transmission ◽  
Full Account ◽  
Flexible Bodies ◽  
Powered Support ◽  
Structural Design Optimization ◽  
Hinge Points ◽  
The Impact

To study the load transfer characteristics of a two-legged shield powered support, a numerical simulation model of the support was established using the multibody dynamics software ADAMS. The model took full account of the hydraulic-elastic deformation characteristics of the support, as a series spring-damper system was used to replace the leg and the equilibrium jack. The canopy, goaf shield, lemniscate bars, and equilibrium jack are equivalent to flexible bodies. The setting force of the leg was provided by the preload of the equivalent spring, the static roof load was simulated using a slope signal, and the impact load was simulated using a step signal. Using the model, the impact and excitation effects of each hinge joint of the support were analyzed under different impact load conditions across the canopy. The results show that the location of the impact load affects the force transmissions of all hinge points of the support. Both the impact effect and the excitation effect are at a minimum when the impact force is located near the leg action line. These results are useful for the adaptive control and structural design optimization of the support.

scholarly journals The influence of advance speed on overburden movement characteristics in longwall coal mining: insight from theoretical analysis and physical simulation

2021 ◽  
Vol 18 (1) ◽  
pp. 163-176
Author(s):  
Penghua Han ◽  
Cun Zhang ◽  
Zhaopeng Ren ◽  
Xiang He ◽  
Sheng Jia
Keyword(s):  
Physical Simulation ◽  
Impact Load ◽  
Main Roof ◽  
Longwall Face ◽  
Mine Safety ◽  
Efficient Production ◽  
Time Space ◽  
Mining Pressure ◽  
The Impact ◽  
Advance Speed

Abstract The advance speed of a longwall face is an essential factor affecting the mining pressure and overburden movement, and an effective approach for choosing a reasonable advance speed to realise coal mine safety and efficient production is needed. To clarify the influence of advance speed on the overburden movement law of a fully mechanised longwall face, a time-space subsidence model of overburden movement is established by the continuous medium analysis method. The movement law of overburden in terms of the advance speed is obtained, and mining stress characteristics at different advance speeds are reasonably explained. The theoretical results of this model are further verified by a physical simulation experiment. The results support the following conclusions. (i) With increasing advance speed of the longwall face, the first (periodic) rupture interval of the main roof and the key stratum increase, while the subsidence of the roof, the fracture angle and the rotation angle of the roof decrease. (ii) With increasing advance speed, the roof displacement range decreases gradually, and the influence range of the advance speed on the roof subsidence is 75 m behind the longwall face. (iii) An increase in the advance speed of the longwall face from 4.89 to 15.23 m/d (daily advancing of the longwall face) results in a 3.28% increase in the impact load caused by the sliding instability of the fractured rock of the main roof and a 5.79% decrease in the additional load caused by the rotation of the main roof, ultimately resulting in a 9.63% increase in the average dynamic load coefficient of the support. The roof subsidence model based on advance speed is proposed to provide theoretical support for rational mining design and mining-pressure-control early warning for a fully mechanised longwall face.

scholarly journals A smart passive MR damper with a hybrid powering system for impact mitigation: An experimental study

2021 ◽  
pp. 1045389X2098808
Author(s):  
S. Jin ◽  
L. Deng ◽  
J. Yang ◽  
S. Sun ◽  
D. Ning ◽  
...  
Keyword(s):  
Impact Velocity ◽  
Mr Damper ◽  
Damping Force ◽  
Softening Effect ◽  
Impact Speed ◽  
Impact Mitigation ◽  
Passive Damper ◽  
Comparison Results ◽  
Wide Range ◽  
The Impact

This paper presents a smart passive MR damper with fast-responsive characteristics for impact mitigation. The hybrid powering system of the MR damper, composed of batteries and self-powering component, enables the damping of the MR damper to be negatively proportional to the impact velocity, which is called rate-dependent softening effect. This effect can keep the damping force as the maximum allowable constant force under different impact speed and thus improve the efficiency of the shock energy mitigation. The structure, prototype and working principle of the new MR damper are presented firstly. Then a vibration platform was used to characterize the dynamic property and the self-powering capability of the new MR damper. The impact mitigation performance of the new MR damper was evaluated using a drop hammer and compared with a passive damper. The comparison results demonstrate that the damping force generated by the new MR damper can be constant over a large range of impact velocity while the passive damper cannot. The special characteristics of the new MR damper can improve its energy dissipation efficiency over a wide range of impact speed and keep occupants and mechanical structures safe.

Grinding Force Model for Low-Speed Grinding Based on Impact Principle

2013 ◽  
Vol 797 ◽  
pp. 123-128
Author(s):  
Ming He Liu ◽  
Xiu Ming Zhang ◽  
Shi Chao Xiu
Keyword(s):  
Sliding Friction ◽  
Impact Load ◽  
Grinding Force ◽  
Calculation Model ◽  
Force Model ◽  
Grinding Process ◽  
Low Speed ◽  
Impact Area ◽  
Force Mechanism ◽  
The Impact

In the low-speed grinding process, the force generated when the wheel grinding the workpiece is the result of sliding friction, plough and cutting. While in the actual study, the cutting process has attracted extensive attention. Impact effect to the entire grinding process on the contact is ignored so that the error exists between the calculation grinding force and the measured grinding force. Basing on the shock effect to the grinding process, the paper divides the contact area into impact area and cutting area. And the model of impact load generated from single grit is built. Moreover, the grinding force theoretical calculation model and total grinding force mathematical model is also constructed by analyzing the impact load affecting on the grinding force mechanism. Finally experimental study verifies the correctness of theoretical analysis.

Study on a Novel MEMS High G Acceleration Sensor

2012 ◽  
Vol 490-495 ◽  
pp. 499-503
Author(s):  
Ping Li ◽  
Yun Bo Shi ◽  
Jun Liu ◽  
Shi Qiao Gao
Keyword(s):  
Resonant Frequency ◽  
Natural Frequency ◽  
Impact Load ◽  
Hopkinson Bar ◽  
Experimental Results ◽  
Structure Parameters ◽  
Acceleration Sensor ◽  
Piezoresistive Effect ◽  
Sensor Structure ◽  
The Impact

This paper presents a novel MEMS high g acceleration sensor based on piezoresistive effect. For the designed sensor structure, the formula of stress, natural frequency and damping was derived in theory, and the resonant frequency can up to 500kHz. After the structure parameters were designed, the sensor was fabricated by the standard processing technology, and the sensitivity was tested by Hopkinson bar. According to the experimental results, the sensitivity of the high g acceleration sensor is 0.125μV/g at the impact load of 164,002g.

The Effective Temperature of Dust Impact Plasmas — Olivine Dust on Tungsten Target

2021 ◽  
Author(s):  
Jiří Pavlů ◽  
Samuel Kočiščák ◽  
Åshild Fredriksen ◽  
Michael DeLuca ◽  
Zoltan Sternovsky
Keyword(s):  
Negative Charge ◽  
Negative Ions ◽  
Charge Carriers ◽  
Dust Particles ◽  
Applied Bias ◽  
Control Grid ◽  
Impact Speed ◽  
Positive Ions ◽  
Effective Temperatures ◽  
The Impact

<p>We experimentally observe both positive and negative charge carriers in impact plasma and estimate their effective temperatures. The measurements are carried on a dust accelerator using polypyrrole (PPy)-coated olivine dust particles impacting tungsten (W) target in the velocity range of 2–18 km/s. We measure the retained impact charge as a function of applied bias potential to the control grid. The temperatures are estimated from the data fit. The estimated effective temperatures of the positive ions are approximately 7 eV and seems to be independent of the impact speed. The negative charge carriers' temperatures vary from as low as 1 eV for the lowest speeds to almost ten times higher speeds. The presented values differ significantly from previous studies using Fe dust particles. Yet, the discrepancy can be attributed to a larger fraction of negative ions in the impact plasma that likely originates from the PPy coating.</p>

Sign in / Sign up

Export Citation Format

Share Document