ROD MODELING OF STRUCTURES LEVERING MECHANISMS WITH DISTRIBUTED INERTIA

2020 ◽  
Vol 69 (1) ◽  
pp. 269-284
Author(s):  
Е. Тemirbekov ◽  
◽  
G. Тukeshova ◽  
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Center Of Mass ◽  
Element Model ◽  
Finite Element Models ◽  
The Finite Element Method ◽  
Contact Points ◽  
Spatial Movement ◽  
Reaction Forces ◽  
Matrix Relation

To reduce inertia of moving links into resultant force and moment vectors and to represent center of mass as node in finite element models are widely-used in mechanical calculations of linkage mechanisms. Considering distributed inertia of motion makes possible to create more precise finite element models in spatial linkage structures. By algebraically summing all the distributed inertial loads acting in both directions, perpendicular and along the axis of a constant cross section link, we can show that their intensity varies linearly along the length of link. Using this approach together with Chasles theorem for a point of free rigid body in projections onto the moving axes in the finite element method for rectilinear homogeneous rod, we reach to a more precise finite element model considering analytically distributed inertia of motion. Besides, we obtained subvectors in matrix relation which binds the generalized reaction forces acting at the contact points of the rod element with nodal generalized elastic movements. These subvectors includes the weight and inertia of a distributed spatial movement of link.

scholarly journals Analysis of Contact Deformations in Support Systems Using Roller Prisms

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2644
Author(s):  
Krzysztof Nozdrzykowski ◽  
Zenon Grządziel ◽  
Paweł Dunaj
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Contact Theory ◽  
Finite Element Analyses ◽  
The Finite Element Method ◽  
Hertz Contact ◽  
Contact Points ◽  
Calculation Results ◽  
Reaction Forces ◽  
Shaft Journal

This article presents the results of finite element analyses of the influence of reaction forces on stresses and strains at the contact points of the rollers of prism supports with cylindrical surfaces of the main journals of large-sized crankshafts. The analyses of strains and stresses, as well as the depth of their occurrences, in the case of the shaft journal and support rollers were carried out using Hertz contact theory and the finite element method. These calculation results proved to be highly consistent. Additionally, they provide a basis for stating that, in the case under consideration, permanent deformations do not significantly affect the values of the measured geometrical deviations nor the profile forms of the supported main crankshaft journals.

A Finite Element Model for Cables With Nonsymmetrical Geometry and Loads

1994 ◽  
Vol 116 (1) ◽  
pp. 14-20 ◽  
Author(s):  
T. T. Le ◽  
R. H. Knapp
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cross Section ◽  
Cross Sections ◽  
Degrees Of Freedom ◽  
Circular Cross Section ◽  
Element Model ◽  
Computer Code ◽  
Deformation Analysis ◽  
Contact Points

A new two-dimensional finite element model is proposed for the deformation analysis of cable cross sections. The deformations of the cable cross section are of considerable design interest because of their effect on the induced torque or rotation of the cable. This model accounts for material orthotropy and nonsymmetrical geometry and loads. Each component of the cable is assumed to possess a circular cross section and is modeled as a macro-element having nodal degrees-of-freedom at all contact points with adjoining components. Usual finite element procedures are applied to solve for the unknown displacements at contact nodal points. The model is implemented in a computer code and is verified by test results obtained for an as-built cable.

scholarly journals Comparisons of finite element models used to predict bending strength of mortise-and-tenon joints

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 5801-5811
Author(s):  
Wengang Hu ◽  
Na Liu
Keyword(s):  
Finite Element ◽  
Bending Strength ◽  
Bending Moment ◽  
Element Model ◽  
Finite Element Models ◽  
The Finite Element Method ◽  
T Joints ◽  
Moment Capacity ◽  
Rigid Model ◽  
Mortise And Tenon

This study aimed to obtain a better method for establishing a finite element model of mortise-and-tenon (M-T) joints. Three types of M-T joint finite element models, which included a whole rigid model, a tie rigid model, and a semi-rigid model, were established and compared with experimental results by predicting the bending moment capacity (BMC) of M-T joints based on the finite element method (FEM). The results showed that the semi-rigid model performed much better than the tie rigid model, followed by the whole rigid model. For the semi-rigid model, the ratios of FEM ranged from 0.85 to 1.09. For the whole rigid model and tie rigid model, the BMC of the M-T joint was overestimated. In addition, the results showed that tenon size remarkably affected the BMC and stiffness of the M-T joint, and tenon width had a greater effect on the BMC of the M-T joint than the tenon length.

Rolling Resistance Calculation Procedure Using the Finite Element Method

2019 ◽  
Vol 48 (3) ◽  
pp. 224-248
Author(s):  
Pablo N. Zitelli ◽  
Gabriel N. Curtosi ◽  
Jorge Kuster
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Rolling Resistance ◽  
Element Model ◽  
The Finite Element Method ◽  
Temperature Changes ◽  
Rubber Compounds ◽  
Different Temperatures ◽  
Materials Used ◽  
Account Temperature

ABSTRACT Tire engineers are interested in predicting rolling resistance using tools such as numerical simulation and tests. When a car is driven along, its tires are subjected to repeated deformation, leading to energy dissipation as heat. Each point of a loaded tire is deformed as the tire completes a revolution. Most energy dissipation comes from the cyclic loading of the tire, which causes the rolling resistance in addition to the friction force in the contact patch between the tire and road. Rolling resistance mainly depends on the dissipation of viscoelastic energy of the rubber materials used to manufacture the tires. To obtain a good rolling resistance, the calculation method of the tire finite element model must take into account temperature changes. It is mandatory to calibrate all of the rubber compounds of the tire at different temperatures and strain frequencies. Linear viscoelasticity is used to model the materials properties and is found to be a suitable approach to tackle energy dissipation due to hysteresis for rolling resistance calculation.

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

scholarly journals Numerical investigation of the effects of unsupported railway sleepers on train-induced environmental vibrations

2017 ◽  
Vol 36 (2) ◽  
pp. 160-176 ◽  
Author(s):  
Seyed-Ali Mosayebi ◽  
Morteza Esmaeili ◽  
Jabbar-Ali Zakeri
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Two Dimensions ◽  
Railway Track ◽  
Sensitivity Analyses ◽  
Regression Equations ◽  
The Finite Element Method ◽  
Technical Literature ◽  
Support Force ◽  
Comparison Of The Results

Review of technical literature regarding to train-induced vibrations shows that the effects of unsupported railway sleepers on this issue have been less investigated. So, the present study was devoted to numerical investigations of the mentioned issue. In this regard, first the problem of longitudinal train–track dynamic interaction was simulated in two dimensions by using the finite element method and the developed model was validated through comparison of the results with those obtained by previous researchers. In the next stage, a series of sensitivity analyses were accomplished to account for the effects of value of gap beneath the unsupported sleeper(s) and the track support stiffness on increasing the sleeper displacement and track support force. Moreover, the raised sleeper support force was introduced as applied load to a two-dimensional plane strain finite element model of track in lateral section and consequently the train-induced vibrations were assessed. As a result, a series of regression equations were established between the peak particle velocity in the surrounding environment of railway track and the sleeper support stiffness for tracks without unsupported sleepers and with one and two unsupported sleepers.

Numerical Simulation of the Effects of Preheating on Electron Beam Additive Manufactured Ti-6Al-4V Build Plate

2016 ◽  
Vol 879 ◽  
pp. 274-278 ◽  
Author(s):  
Jun Cao ◽  
Philip Nash
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Finite Element ◽  
Electron Beam ◽  
Cross Section ◽  
Element Model ◽  
Normal Direction ◽  
Thermal Residual Stresses ◽  
Longitudinal Residual Stress ◽  
Middle Cross Section

In an earlier study, a 3-D thermomechanical coupled finite element model was built and experimentally validated to investigate the evolution of the thermal residual stresses and distortions in electron beam additive manufactured Ti-6Al-4V build plates. In this study, an investigation using this robust and accurate model was focused on an efficient preheating method, in which the electron beam quickly scanned across the substrate to preheat the build plate prior to the deposition. Various preheat times, beam powers, scan rates, scanning paths and cooling times (between the end of current preheat scan/deposition layer and the beginning of the next preheat scan/deposition layer) were examined, and the maximum distortion along the centerline of the substrate and the maximum longitudinal residual stress along the normal direction on the middle cross-section of the build plate were quantitatively compared. The results show that increasing preheat times and beam powers could effectively reduce both distortion and residual stress for multiple layers/passes components.

Contrastive Study on Finite Element Models of High-Strength Pipelines Crossing Active Faults

2016 ◽  
Vol 850 ◽  
pp. 957-964
Author(s):  
Wei Zheng ◽  
Hong Zhang ◽  
Xiao Ben Liu ◽  
Le Cai Liang ◽  
Yin Shan Han
Keyword(s):  
Finite Element ◽  
Design Method ◽  
Active Faults ◽  
Shell Element ◽  
High Strength ◽  
Element Model ◽  
Beam Element ◽  
Finite Element Models ◽  
Fixed Boundary ◽  
Equivalent Boundary

There is a potential for major damage to the pipelines crossing faults, therefore the strain-based design method is essential for the design of buried pipelines. Finite element models based on soil springs which are able to accurately predict pipelines’ responses to such faulting are recommended by some international guidelines. In this paper, a comparative analysis was carried out among four widely used models (beam element model; shell element model with fixed boundary; shell element model with beam coupled; shell element model with equivalent boundary) in two aspects: differences of results and the efficiency of calculation. The results show that the maximum and minimum strains of models coincided with each other under allowable strain and the calculation efficiency of beam element model was the highest. Besides, the shell element model with beam coupled or equivalent boundary provided the reasonable results and the calculation efficiency of them were higher than the one with fixed boundary. In addition, shell element model with beam coupled had a broader applicability.

Free Vibration Analysis for Tapered Cross-Section Steel-Concrete Composite Material Beam

2017 ◽  
Vol 893 ◽  
pp. 380-383
Author(s):  
Jun Xia ◽  
Z. Shen ◽  
Kun Liu
Keyword(s):  
Finite Element ◽  
Composite Material ◽  
Cross Section ◽  
Vibration Analysis ◽  
Free Vibration Analysis ◽  
Element Model ◽  
Composite Beams ◽  
Shear Connection ◽  
The Common ◽  
Interlayer Slip

The tapered cross-section beams made of steel-concrete composite material are widely used in engineering constructions and their dynamic behavior is strongly influenced by the type of shear connection jointing the two different materials. The 1D high order finite element model for tapered cross-section steel-concrete composite material beam with interlayer slip was established in this paper. The Numerical results for vibration nature frequencies of the composite beams with two typical boundary conditions were compared with ANSYS using 2D plane stress element. The 1D element is more efficient and economical for the common tapered cross-section steel-concrete composite material beams in engineering.

Behavior of Structures Using Simple Plastic Hinge Theory

1994 ◽  
Author(s):  
Ramakrishnan Maruthayappan ◽  
Hamid M. Lankarani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cantilever Beam ◽  
Reliable Method ◽  
Plastic Hinge ◽  
Element Model ◽  
Finite Element Models ◽  
Computational Program ◽  
Hinge Model ◽  
The Impact

Abstract The behavior of structures under the impact or crash situations demands an efficient modeling of the system for its behavior to be predicted close to practical situations. The various formulations that are possible to model such systems are spring mass models, finite element models and plastic hinge models. Of these three techniques, the plastic hinge theory offers a more accurate model compared to the spring mass formulation and is much simpler than the finite element models. Therefore, it is desired to model the structure using plastic hinges and to use a computational program to predict the behavior of structures. In this paper, the behavior of some simple structures, ranging from an elementary cantilever beam to a torque box are predicted. It is also shown that the plastic hinge theory is a reliable method by comparing the results obtained from a plastic hinge model of an aviation seat structure with that obtained from a finite element model.

Sign in / Sign up

Export Citation Format

Share Document