Butyl Networks Containing Unattached Polyisobutylene Chains: Part II, Correlation of Tear, Tensile, and Hysteretic Properties

1986 ◽  
Vol 59 (2) ◽  
pp. 347-360 ◽  
Author(s):  
G. R. Hamed ◽  
F. Ogbimi
Keyword(s):  
Molecular Weight ◽  
Crack Tip ◽  
The Other ◽  
Low Molecular Weight ◽  
Load Bearing ◽  
Tear Strength ◽  
Tearing Energy ◽  
High Molecular Weight Polyisobutylene ◽  
Hysteretic Properties ◽  
Crack Tip Blunting

Abstract Butyl networks containing either unattached polyisobutylene chains or a low-molecular-weight plasticizer have been made by crosslinking butyl rubber in the presence of one of these diluents. With dodecane as a plasticizer, tear strength is reduced both because of a decrease in the density of load-bearing chains and diminished hysteresis. On the other hand, when the diluent is a high-molecular-weight polyisobutylene, tear strength is enhanced if the test rate is sufficiently high. In this case, the polyisobutylene chains are load bearing (at least initially) before slipping at higher strains to relieve local crack-tip stresses and blunt the propagating tear. This hysteretic mechanism delays the onset of crack propagation, thereby enhancing the fracture energy. However, at low tear rates, in which there is adequate time for the unattached chains to relax such that they bear little load and hysteresis is minimized, tear strength decreases with increasing free-chain content—much the same as occurs with a low-molecular-weight diluent. Finally, under conditions in which the average propagating tearing energy is enhanced for the butyl-polyisobutylene system, the initiation tearing energy is increased only moderately. This suggests that crack-tip blunting during steady-state tearing is at least partially responsible for increases in strength in the presence of free chains.

scholarly journals Bridge-therapy with enoxaparin in the preoperative period of endarterectomy

2010 ◽  
Vol 68 (5) ◽  
pp. 775-777
Author(s):  
Jair Leopoldo Raso ◽  
Rogério Zenóbio Darwich ◽  
Francisco de Lucca Jr ◽  
Romeu Valle Santana ◽  
Marco Túlio Tanure ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Mortality Rate ◽  
Prospective Study ◽  
Low Molecular Weight Heparin ◽  
The Other ◽  
Low Molecular Weight ◽  
Preoperative Period ◽  
Safe Strategy ◽  
A Prospective Study ◽  
Bridge Therapy

Cervical clot is one of the complications of endarterectomy. This risk may be higher in patients using aspirin or clopidogrel. On the other hand, stroke may occur if the medication is interrupted before surgery. We carried out a prospective study of 124 endarterectomies in 119 patients in which aspirin or clopidogrel was stopped and a bridge-therapy with enoxaparin was administered preoperatively. There was no case of stroke during the period of the bridge-therapy. One patient developed cervical clot (0.8%) in the fifth postoperative day. Mortality rate in this series was 0.8%. There was no complication directly related to the use of enoxaparin. Bridge-therapy with low molecular weight heparin is a safe strategy for patients elected for endarterectomy

In Vitro Characterization Of Low Molecular Weight Fractions Of Heparin

1981 ◽  
Author(s):  
Jawed Fareed ◽  
Harry L Messmore ◽  
Daniel A Walz ◽  
Jean Choay ◽  
J C Lormeau
Keyword(s):  
Molecular Weight ◽  
The Other ◽  
Low Molecular Weight ◽  
In Vitro Test ◽  
Thrombin Time ◽  
Specific Test ◽  
Platelet Factor ◽  
At Iii ◽  
Heparin Fractions

Numerous extraction, chromatographic (ion exchange, gel, and affinity), chemical and enzymatic degradation methods have been employed to obtain heparin fractions. The present assays to evaluate potency (e.g. pharmacopeial and coagulant) do not truly reflect the antithrombotic properties of these fractions. In addition, the synthetic peptide substrate based assays to measure the anti Xa activity do not correlate with the coagulant anti Xa assays. We have developed an in vitro test battery to evaluate low molecular weight heparin fractions. Porcine mucosal heparin fractions are assayed for anti Xa activity in coagulant and amidolytic assays and the results are expressed as a ratio. The effect of these fractions on coagulant assays such as prothrombin time (PT), partial thromboplastin time (PTT), thrombin time (TT), Stypven time (ST) on freshly prepared normal human plasma (NHP) is determined The retention characteristics of these fractions on platelet factor 4 and AT-III bound sepharose columns were also determined. We have compared the extracted and chemically depolymerized heparin fractions and found that the anti Xa activity doesn’t always correlate with the other parameters studied. The extracted fractions were slightly stronger in the USP assays and showed a biphasic retention on the PF-4 column whereas the chemically depolymerized product showed only one peak. On the other hand, on the AT-III column both fractions showed similar elution patterns. Our studies suggest that heparin and its fractions exhibit differential behavior on various assays and a specific test may not be used as an index of the potency of their antithrombotic effects. Furthermore, the potency of these fractions should be stated on a weight basis when evaluated in the in vivo animal models rather than in terms of a specific test (e.g. anti Xa activity and US Pharmacopeial assays).

STUDIES ON THE ISOLATION AND NATURE OF THE 'TERREGENS FACTOR'

1954 ◽  
Vol 32 (1) ◽  
pp. 400-406 ◽  
Author(s):  
M. O. Burton ◽  
F. J. Sowden ◽  
A. G. Lochhead
Keyword(s):  
Amino Acids ◽  
Molecular Weight ◽  
Ferric Iron ◽  
Test Organism ◽  
The Other ◽  
Inorganic Salts ◽  
Low Molecular Weight ◽  
Straight Chain ◽  
Heat Stable ◽  
Growth Promoting

A procedure is described for the production and concentration of the 'terregens factor' (TF), a bacterial growth promoting substance synthesized by Arthrobacter pascens and essential for the growth of Arthrobacter terregens. From culture filtrates of A. pascens cultivated in a medium of inorganic salts and sucrose, concentrates of TF may be obtained that are active at 0.001 μgm. Per ml., heat stable and contain about 12.7% nitrogen. Acid hydrolysis yielded a number of amino acids, including glutamic acid, glycine, α–alanine, valine, leucine, proline, lysine, and arginine, as well as some unidentified compounds; however, TF does not appear to be a low molecular weight straight chain peptide.Although TF contains no iron, it combines readily with ferrous or ferric iron to form reddish-brown complexes with this metal. Activity for A. terregens is shown by certain iron containing complexes as hemin, coprogen, and ferrichrome. On the other hand none is shown by cytochrome or pulcherrimin; however, aspergillic acid, structurally related to the latter, possesses some growth promoting activity for the test organism.

scholarly journals Viscoelastic Properties of Unentangled Multicyclic Polystyrenes

Polymers ◽  
2018 ◽  
Vol 10 (9) ◽  
pp. 973 ◽  
Author(s):  
Zhi-Chao Yan ◽  
Md. Hossain ◽  
Michael Monteiro ◽  
Dimitris Vlassopoulos
Keyword(s):  
Molecular Weight ◽  
Shear Viscosity ◽  
Viscoelastic Properties ◽  
Dilution Effect ◽  
The Other ◽  
Low Molecular Weight ◽  
Zero Shear Viscosity ◽  
Rouse Model ◽  
Loop Size ◽  
Linear Chains

We report on the viscoelastic properties of linear, monocyclic, and multicyclic polystyrenes with the same low molecular weight. All polymers investigated were found to exhibit unentangled dynamics. For monocyclic polymers without inner loops, a cyclic-Rouse model complemented by the contribution of unlinked chains (whose fraction was determined experimentally) captured the observed rheological response. On the other hand, multicyclic polymers with inner loops were shown to follow a hierarchical cyclic-Rouse relaxation with the outer loops relaxing first, followed by the inner loop relaxation. The influence of unlinked linear chains was less significant in multicyclic polymers with inner loops. The isofrictional zero-shear viscosity decreased with increasing number of constrained segments on the coupling sites, which was attributed to the decreasing loop size and the dilution effect due to the hierarchical relaxation.

Fractionation of the Color of Pure Maple and Other Sirups by Gel Filtration

1965 ◽  
Vol 48 (3) ◽  
pp. 493-497
Author(s):  
E E Stinson ◽  
C O Willits
Keyword(s):  
Molecular Weight ◽  
Gel Filtration ◽  
Cane Sugar ◽  
The Other ◽  
Low Molecular Weight ◽  
Brown Sugar ◽  
Maple Sugar ◽  
Molecular Weight Fractions ◽  
Color Fraction

Abstract The colorants of pure maple, cane and maple, refined cane sugar, and light brown sugar sirups were separated into two fractions, one of high- and the other of lowmolecular weights, by means of gel filtration. The ratio of the amounts of high- to the low-molecular weight fractions of pure maple was the lowest of the four sirups and serves as a means of differentiation from these sirups. The color fraction ratio was highest for blended cane-maple sugar sirup. Many maple sirups are also distinguished by a pink band formed on the gel filtration column.

Solution Autoxidation of EPDM and Termonomers

1972 ◽  
Vol 45 (4) ◽  
pp. 1125-1135
Author(s):  
H. Schnecko ◽  
J. S. Walker
Keyword(s):  
Activation Energy ◽  
Molecular Weight ◽  
Oxygen Uptake ◽  
The Other ◽  
Low Molecular Weight ◽  
Kinetic Behavior ◽  
Ethylene Propylene ◽  
Very High

Abstract Oxygen uptake of 3 low molecular weight ethylene-propylene terpolymers (EPDM) and their respective bicyclic diolefin termonomers (dicyclopentadiene, ethylidene norbornene, and methyl endomethylene hexahydronaphthalene) has been measured at ⩽70°. From the kinetic behavior and from the activation energy, it has been concluded that ethylidene norbornene reacts differently from the other two monomers; its autoxidation is much slower. In all cases, conversion is not very high due to formation of an unidentified inhibitor.

scholarly journals Effect of Changes in Physical Properties of Granular Activated Carbon (GAC) on the Adsorption of Natural Organic Matter (NOM) with Increasing the Number of Thermal Regeneration: Pore Size and NOM Molecular Weight

2021 ◽  
Vol 43 (7) ◽  
pp. 537-546
Author(s):  
Heejong Son ◽  
Sangki Choi ◽  
Byungryul An ◽  
Hyejin Lee ◽  
Hoon-Sik Yoom
Keyword(s):  
Molecular Weight ◽  
Organic Matter ◽  
Activated Carbon ◽  
Pore Structure ◽  
Adsorption Capacity ◽  
Natural Organic Matter ◽  
Volume Ratio ◽  
The Other ◽  
Low Molecular Weight ◽  
Thermal Regeneration

Objectives : The purpose of this study was to evaluate the effect of increasing the number of regeneration of granular activated carbon (GAC) on the adsorption capacity of natural organic matter (NOM), and to suggest the technical process options associated the limit number of regeneration and the efficient use of regenerated GAC.Methods : The physicochemical properties of virgin and thermally regenerated GAC were analyzed. To evaluate the NOM adsorption capacity of virgin- and regenerated-GAC, five laboratory-scale columns packed with virgin- and regenerated-GAC were used for treating effluent from pilot-scale drinking water treatment facility. The NOM concentration in the influent and the effluent treated by each column was analyzed by LC-OCD (liquid chromatography-organic carbon detector) to evaluate the adsorption capacity of each NOM fractions (humic substances (HS), building blocks (BB), low molecular weight organics (LMWs)).Results and Discussion : Due to the change in the pore structure of GAC by thermal regeneration, the volume of micropores (< 2 nm) decreased, while the volume of mesopores (> 2 nm) increased. The volume ratio of micropore in virgin-GAC was about 60%, but it gradually decreased as the number of regenerations increased, resulting that the volume ratio of micropore in the 5th-regenerated (5th-Re) GAC decreased to 23%. On the other hand, the volume ratio of mesopore increased in proportion to the number of regenerations from 40% of the virgin GAC to 77% of the 5th-Re-GAC. The DOC adsorption capacities of the regenerated GACs were higher than that of virgin GAC, and the DOC adsorption capacity increased as the number of regenerations increased. As a result of comparing the adsorption capacity of virgin- and regenerated-GAC by NOM fractions, the adsorption capacity of high molecular weight NOM, such as HS, increased by 1.5 to 1.7 times as the number of regenerations increased. In contrast, the adsorption capacity of low molecular weight NOM, such as BB and LMWs, decreased by 78% and 48% as the number of regeneration increased. The limit number of regeneration was evaluated based on that the adsorption capacity (qe) of each NOM fractions keep over than 70% relative to its virgin GAC. As a result, the adsorption capacity for low molecular weight NOM was greatly reduced in GAC regenerated over than 3rd time, so that the 2nd-Re-GAC was valid to keep 70% removal of whole NOM fractions. Low adsorption of low molecular weight NOM (BB and LMWs) by 3rd-Re-GAC could be complemented by using together with virgin-GAC, and low adsorption of high molecular NOMs (HS) could be compensated as well.Conclusions : Due to the change in the pore structure of GAC by thermal regeneration, the DOC adsorption capacity was higher in regenerated GAC than its virgin-GAC, and the adsorption capacity of DOC and high molecular weight NOM (HS) was enhanced as the number of regenerations increased. On the other hand, the pore volume of micropore was reduced by regenerations, and in more than 3rd times regenerations, the adsorption capacity of low molecular weight NOMs (BB and LMWs) was reduced by less than 70% compared to its virgin GAC, so that 2nd-Re-GAC was suggested for suitable GAC. When using a mixture of virgin- and 3rd-Re-GAC, low adsorption of low molecular weight NOM (BB and LMWs) by 3rd-Re-GAC could be complemented by using together with virgin-GAC, and low adsorption of high molecular NOMs (HS) could be compensated as well.

scholarly journals Potential immunological markers for diagnosis and therapeutic assessment of toxocariasis

2011 ◽  
Vol 53 (2) ◽  
pp. 61-65 ◽  
Author(s):  
Guita Rubinsky-Elefant ◽  
Sumie Hoshino-Shimizu ◽  
Cristina Miuki Abe Jacob ◽  
Maria Carmen Arroyo Sanchez ◽  
Antonio Walter Ferreira
Keyword(s):  
Molecular Weight ◽  
Toxocara Canis ◽  
The Other ◽  
Low Molecular Weight ◽  
Therapeutic Assessment ◽  
Igg Antibodies ◽  
Follow Up Study ◽  
Immunological Markers ◽  
Iga Antibodies

In human toxocariasis, there are few approaches using immunological markers for diagnosis and therapeutic assessment. An immunoblot (IB) assay using excretory-secretory Toxocara canis antigen was standardized for monitoring IgG, IgE and IgA antibodies in 27 children with toxocariasis (23 visceral, three mixed visceral and ocular, and one ocular form) for 22-116 months after chemotherapy. IB sensitivity was 100% for IgG antibodies to bands of molecular weight 29-38, 48-54, 95-116, 121-162, >205 kDa, 80.8% for IgE to 29-38, 48-54, 95-121, > 205 kDa, and 65.4% for IgA to 29-38, 48-54, 81-93 kDa. Candidates for diagnostic markers should be IgG antibodies to bands of low molecular weight (29-38 and 48-54 kDa). One group of patients presented the same antibody reactivity to all bands throughout the follow-up study; in the other group, antibodies decayed partially or completely to some or all bands, but these changes were not correlated with time after chemotherapy. Candidates for monitoring patients after chemotherapy may be IgG antibodies to > 205 kDa fractions, IgA to 29-38, 48-54, 81-93 kDa and IgE to 95-121 kDa. Further identification of antigen epitopes related to these markers will allow the development of sensitive and specific immunoassays for the diagnosis and therapeutic assessment of toxocariasis.

Comparative Studies on An Anti-Xa Enriched Ultra Low Molecular Weight Heparin with Bemiparin

Blood ◽  
2010 ◽  
Vol 116 (21) ◽  
pp. 4394-4394
Author(s):  
Debra Hoppensteadt ◽  
Angel Gray ◽  
Josephine Cunanan ◽  
Walter Jeske ◽  
Jeanine M. Walenga ◽  
...  
Keyword(s):  
Molecular Weight ◽  
Platelet Aggregation ◽  
Whole Blood ◽  
Anticoagulant Activity ◽  
The Other ◽  
Positive Interactions ◽  
Low Molecular Weight ◽  
Significant Activity ◽  
Thrombin Time ◽  
Low Molecular Weight Heparins

Abstract Abstract 4394 Most low molecular weight heparins (LMWHs) have a mean molecular weight in the range of 4–6 kDa and anti-Xa/IIa ratios of 3–6. Further depolymerization of porcine mucosal heparin results in the generation of Ultra low molecular weight heparins (ULMWHs) with a molecular weight range of 2–4 kDa with proportionately decreased anti-Xa and anti-IIa activities. Bemiparin (Rovi, Madrid, Spain) represents one such ULMWH. AVE 5026 (Sanofi-Aventis, Paris, France) is a unique ULMWH (2.5 kDa) which exhibits higher affinity to antithrombin (AT) and therefore, enhanced anti-Xa activity. Because of the compositional differences between these two agents, it was hypothesized that each of these agents will have distinct anticoagulant, antiprotease and thrombin generation effects. Each of these agents was supplemented to native whole blood. Anticoagulant activity was measured using ACT, TEG, PT, APTT, thrombin time and Heptest assays. Similar studies were carried out in plasma. Amidolytic assays were used to determine the anti-Xa and anti-IIa activities. Both agents were also tested for the interactions with heparin cofactor II (HC II) and AT and were compared in the HIT antibody screening assay using platelet aggregation. In whole blood clotting assays bemiparin showed a strong anticoagulant activity in comparison to AVE 5026. Both agents also exhibited assay dependent differences in the APTT, heptest and thrombin time assays. AVE 5026 exhibited a higher anticoagulant activity in the heptest whereas bemiparin showed a stronger anticoagulant effect in the other clot based assays. In the amidolytic anti-Xa assay, AVE 5026 showed an activity of 156U/mg compared to 86 U/mg for bemiparin. In the anti-IIa assay bemiparin showed a higher activity (10 U/mg) in comparison to AVE 5026 (3.2 U/mg). The calculated Xa/IIa ratio of AVE 5026 was > 48, whereas it was 8.6 for bemiparin. While bemiparin exhibited interactions with HC II, AVE 5026 did not show significant activity in the tested concentrations (anti-IIa – IC50: 1.10±.45 μ M and >3.44±.00 μ M, respectively). On the other hand, AVE 5026 exhibited stronger interactions with AT in comparison to bemiparin (anti-FXA – IC50: .223±.03 μ M and .894±.06 μ M, respectively). Interestingly, heparinase digestion of the two products resulted in a complete loss of anti-IIa activity, but residual anti-Xa activity was found. AVE 5026 exhibited stronger anti-Xa interactions even after heparinase digestion. In the heparin induced platelet aggregation assay at 2.5 μ g/ml, bemiparin showed a relatively higher prevalence of positive interactions with HIT antibodies, whereas AVE 5026 showed a much lower prevalence (slope; AVE 5026 compared bemiparin, p=0.012). Bemiparin exhibited greater platelet factor 4 neutralization in comparison to AVE 5026. These studies clearly demonstrate that while bemiparin behaves like a typical ULMWH, AVE 5026 behaves differently in the different assays. Moreover, the oligosaccharide composition of the two products, in terms of distribution profile structure, is also different. Therefore, AVE 5026 does not represent a typical depolymerized ULMWH and is expected to exhibit a distinct pharmacologic and clinical profile. Disclosures: Hoppensteadt: Sanofi-Aventis: Research Funding.

Radioisomerization and Photoisomerization of Liquid 2 -Butenes in the Presence of Sulfur Compounds

1974 ◽  
Vol 52 (12) ◽  
pp. 2337-2340 ◽  
Author(s):  
Guy J. Collin ◽  
Patrick M. Perrin ◽  
François X. Garneau
Keyword(s):  
Molecular Weight ◽  
Hydrogen Sulfide ◽  
Liquid Phase ◽  
Molecular Oxygen ◽  
Carbon Disulfide ◽  
Sulfur Hexafluoride ◽  
The Other ◽  
Isomerization Reaction ◽  
Low Molecular Weight ◽  
Cis And Trans

The liquid phase radiolysis and photolysis of cis- and trans-2-butenes were studied in the presence of various additives. A very efficient isomerization of 2-butenes was achieved by the addition of thiols of low molecular weight (hydrogen sulfide, methyl and isopropyl mercaptans). In the absence of molecular oxygen, we have observed G values (trans-2-butene) of the order of 90 000. On the other hand, little or no isomerization occurred in the presence of carbon disulfide, sulfur hexafluoride, and tert-dodecylmercaptan. Although the majority of the additives have no effect on the 2-butene:hydrogen sulfide system, conjugated diolefins block the isomerization reaction. These diolefins disappear from the reaction mixture.

Sign in / Sign up

Export Citation Format

Share Document