The Sensitive Detection of Organically Combined Bromine

1939 ◽  
Vol 12 (1) ◽  
pp. 103-104
Author(s):  
F. Kirchhof

Abstract When a few drops of concentrated copper sulfate solution are added to a concentrated solution of potassium bromide, this solution turns yellow or brownish. When it is warmed, the color darkens, and on cooling or by dilution it becomes light again; finally at a definite concentration the color becomes yellow-green. If a drop of the concentrated solution is placed on chemically pure filter paper and is allowed to dry, a bright or dark purple-red color is obtained, the shade depending on the method of drying. This color appears even when drying is at room temperature; it becomes paler when one breathes on the sample, and disappears completely when the colored spot is moistened with water, but on drying reappears as a pale rose color, the intensity of which depends on the concentration. The same purple color, but more brilliant, appears when a few drops of concentrated sulfuric acid are added to potassium bromide—copper bromide solution. In this case the color is extraordinarily intense, and it is visible even when only 0.5 mg. of bromine per liter is present.

2021 ◽  
Vol 108 ◽  
pp. 103194
Author(s):  
Francisco R.A. Ziegler-Rivera ◽  
Blanca Prado ◽  
Alfonso Gastelum-strozzi ◽  
Jorge Márquez ◽  
Lucy Mora ◽  
...  

2021 ◽  
Author(s):  
Rahul Kumar Kushwaha ◽  
Ambresh Mallya ◽  
Dipen Sahu ◽  
Jaya Krishna Meka ◽  
Sheng-Lung Chou ◽  
...  

<p>Benzene (C<sub>6</sub>H<sub>6</sub>) ice has been observed in the Titan’s stratosphere [1], and benzonitrile (C<sub>6</sub>H<sub>5</sub>CN) is a possible constituent in the benzene and nitrogen-rich environment of Titan’s atmosphere [2]. The energetic processing of such aromatic molecules can synthesize large and complex aromatic molecules such as the Polycyclic Aromatic Hydrocarbons (PAHs). To-date a number of laboratory experiments have reported the formation of complex organics from the energetic processing of aromatic molecules [3-6]. In particular, Scanning Electron Microscopy (SEM) micrographs of the residues resulting from irradiated benzene ices are found to contain geometrically shaped particles [6]. Therefore, by employing electron microscopes, we can understand the physical nature of the dust leftover from the aromatic molecule irradiation.</p> <p>In the present investigation, we subjected benzonitrile ice made at 4 K to vacuum ultraviolet (9 eV) radiation at two beamlines, BL03 and BL21A2 of Taiwan Light Source at NSRRC, Taiwan. After irradiation, the ice was warmed to room temperature, which left a brownish residue on the Potassium Bromide (KBr) substrate. The VUV spectrum of the residue is observed to have characteristic aromatic signatures. The residue is then transferred to a quantifoil grid for High-Resolution Transmission Electron Microscope (HR- TEM) imaging. HR-TEM micrographs revealed the presence of graphene in the residue. This result suggests that N-graphene could be present in benzene and nitrogen-rich icy clouds of Titan. The high masses observed by the Cassini plasma spectrometer in Titan’s atmosphere could then be attributed to the presence of N-graphene along with the more common tholins [7].</p> <p><strong>References</strong></p> <p>[1] Vinatier S. et al. (2018) <em>Icarus, 310,</em> 89.</p> <p>[2] Loison J. C. et al. (2019) <em>Icarus 329,</em> 55.</p> <p>[3] Strazzulla G. et al. (1991) <em>A&A, 241</em>, 310.</p> <p>[4] Callahan M. P. et al. (2013) <em>Icarus, 226</em>, 1201.</p> <p>[5] James R. et al. (2019) <em>RSC Adv. 9</em> (10), 5453.</p> <p>[6] Rahul K. K. et al. (2020) <em>Spectrochim. Acta A, 231, </em>117797.</p> <p>[7] Rahul K. K. et al. (2020) <em>arXiv:2008.10011</em>.</p>


2019 ◽  
Vol 73 (11) ◽  
pp. 945-946
Author(s):  
Rachel Fischer ◽  
Marco Oetken

For aluminum, a new visualization method is presented in which copper is deposited electrochemically. The fingerprint on the aluminum (trace carrier) serves as an insulator as it prevents direct contact between electrolyte and aluminum. The decisive factor is the choice of an ammoniacal copper sulfate solution, which acts as a corrosion inhibitor due to the ammonia molecules. This enables uniform copper deposition on aluminum and thus the development of a clearly defined negative image.


2007 ◽  
Vol 353-358 ◽  
pp. 2025-2028 ◽  
Author(s):  
Ikuo Shohji ◽  
Susumu Arai ◽  
Naoki Kano ◽  
Noboru Otomo ◽  
Masahisa Uenishi

A Cu brazing sheet has been developed using a Cu-P composite plating method. A Cu-P composite plating layer, which contains 7mass%P, was formed on a Cu plate with a copper sulfate solution including P particles. The melting start temperature of the Cu-P composite layer was determined to be approximately 765°C. Microstructure and joint strength of a brazed joint with the Cu-P composite layer were investigated and compared with those of the joint with a conventional Cu-7P filler foil. As the results of the study, it was clarified that the Cu-P composite layer developed is feasible to use as a brazing material for Cu and Cu alloys.


2004 ◽  
Vol 836 ◽  
Author(s):  
Susan Huang ◽  
Harry Efstathiadis ◽  
Pradeep Haldar ◽  
Hee-Gyoun Lee

ABSTRACTWe report on a novel use of nanorod arrays for organic based solar cell devices. A metal foil with copper nanorods attached to the surface was developed by electrodepositing copper from a copper sulfate solution into an anodic alumina oxide (AAO) template that had been coated with a metal on one side. The AAO membrane was dissolved in NaOH leaving behind an aligned array of copper nanorods. This nanorod array was evaluated to explore the possibility of increasing the power conversion efficiency of organic solar cells. Nanorod array characteristics were investigated by focus ion beam, scanning electron microscopy, and x-ray diffraction spectroscopy. A solar cell device was made by applying a polymer layer of poly(2-methoxy-5-(3', 7'-dimethyloctyloxy)-1, 4-phenylene-vinylene) (MDMO-PPV) mixed with 6, 6 phentl-C61-butyl acid-methylester (PCBM) onto the copper nanorod array and sandwiching it with a film of poly(3, 4-ethylenedioxythiophene): poly(styrene-sulfonate) (PEDOT:PSS) applied onto a indium tin oxide coated glass substrate.


2008 ◽  
Vol 8 (7) ◽  
pp. 3416-3421
Author(s):  
K. Valenzuela ◽  
S. Raghavan ◽  
P. A. Deymier ◽  
J. Hoying

Microtubules (MTs) are self-assembling, protein-based, tubular structures several micrometers long with outer and inner diameters of 25 nm and 15 nm, respectively. This aspect ratio makes MTs ideal templates for producing nanowires for applications such as electrical nano-interconnects. MTs are poorly conductive and their use as interconnects necessitates their metallization. We report a process for metallization of MTs with copper using a biologically benign electroless deposition chemistry consisting of copper sulfate solution containing acetic acid as a complexant and ascorbic acid as reducing agent. The pH of the plating bath is controlled such that copper metallization occurs without disassembling the MTs. Electron microscopic characterization of the morphology and dimensions of the copper nanowires shows that metallization for approximately 1 minute produces a uniform nanowire with an average diameter of approximately 15 nm, suggesting that metallization is initiated selectively from the MT inner core.


2014 ◽  
Vol 84 (19) ◽  
pp. 2026-2035 ◽  
Author(s):  
Bing Li ◽  
Dapeng Li ◽  
Jiping Wang

A three-axis automatic robot was coupled with a precision liquid dispenser to deposit copper on fabrics to be used as the conductive layer for assembly of textile-based flexible microstrip patch antennas. Two reactive solutions, copper sulfate and sodium borohydride, were sequentially dispensed on fabrics and a conductive copper was produced in situ and in real time, through a simple redox mechanism. Driving pressure, the number of dispensing cycles, concentration and composition (i.e. the addition of a complexing agent sodium citrate to the copper sulfate solution) of the reactive solutions were studied to optimize the dispensing process in favor of rapid copper deposition. The electrical performance of the resulting copper deposit and its adhesion to the textile substrates were characterized. A copper coating of about 0.2 ohm/□ sheet resistance could be prepared in less than 1 hour under a 45 kPa driving pressure, at a 200 mm·s−1 moving speed, and within 60 dispensing cycles.


Sign in / Sign up

Export Citation Format

Share Document