scholarly journals Narrowband NIR-Induced In Situ Generation of the High-Energy Trans Conformer of Trichloroacetic Acid Isolated in Solid Nitrogen and its Spontaneous Decay by Tunneling to the Low-Energy Cis Conformer

2015 ◽  
Vol 88 (4) ◽  
pp. 377-386 ◽  
Author(s):  
R. F. G. Apóstolo ◽  
R. R. F. Bento ◽  
R. Fausto





2021 ◽  
Vol 126 (5) ◽  
Author(s):  
Zan Nie ◽  
Fei Li ◽  
Felipe Morales ◽  
Serguei Patchkovskii ◽  
Olga Smirnova ◽  
...  


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Amy Shore ◽  
Rachel Wood

AbstractCloudina is a globally distributed Ediacaran metazoan, with a tubular, funnel-in-funnel form built of thin laminae (ca. 1–10 μm). To what degree local environmental controlled morphology, and whether early diagenesis controlled the degree of calcification of Cloudina, is debated. Here we test these hypotheses by considering assemblages from four, coeval localities from the Upper Omkyk Member, Nama Group, Namibia, from inner ramp to mid-ramp reef across the Zaris Subbasin. We show that sinuosity of the Cloudina tube is variable between sites, as is the relative thickness of the tube wall, suggesting these features were environmentally controlled. Walls are thickest in high-energy reef settings, and thinnest in the low-energy, inner ramp. While local diagenesis controls preservation, all diagenetic expressions are consistent with the presence of weakly calcified, organic-rich laminae, and lamina thicknesses are broadly constant. Finally, internal ‘cements’ within Cloudina are found in all sites, and pre-date skeletal breakage, transport, as well as syn-sedimentary botryoidal cement precipitation. Best preservation shows these to be formed by fine, pseudomorphed aragonitic acicular crystals. Sr concentrations and Mg/Ca show no statistically significant differences between internal Cloudina cements and botryoidal cements, but we infer all internal cements to have precipitated when Cloudina was still in-situ and added considerable mechanical strength, but may have formed post-mortem or in abandoned parts of the skeleton.



1988 ◽  
Vol 128 ◽  
Author(s):  
Eric Chason ◽  
K. M. Horn ◽  
J. Y. Tsao ◽  
S. T. Picraux

ABSTRACTUsing in situ, real-time reflection high energy electron diffraction (RHEED), we have measured the evolution of Ge (001) surface morphology during simultaneous molecular beam epitaxy and Ar ion beam bombardment. Surprisingly, low-energy Ar ions during growth tend to smoothen the surface. Bombardment by the ion beam without growth roughens the surface, but the surface can be reversibly smoothened by restoring the growth beam. We have measured the effect of such “ion beam growth smoothening” above and below the critical temperature for intrinsic growth roughening. At all measured growth temperatures the surface initially smoothens, but below the critical roughening temperature the final surface morphology is rough whereas above this temperature the final morphology is smooth.



Author(s):  
M. J. Sanders ◽  
H. Jeanes ◽  
S. Fray ◽  
H.-U. Arnold

A need was identified for the in-situ size reduction of large components such as glove boxes, tanks and other components. A development programme resulted in a new cutting method that could be remotely deployed for the in-situ segmentation of large components of this type. RWE NUKEM has selected RASP as acronym for this technology Remotely-Operated Advanced Segmentation Process or RASP. A review of the standard manual cutting methods highlighted a number of significant shortcomings including operative safety; high energy cutting tools generating high temperatures; spread of contamination over wide areas; risk from sharp edges and operative fatigue. The development of new technology was therefore focused on improving safety for operatives and developing an inherently safe and flexible technology, which can be used for in-situ segmentation of any large components of various sizes and configurations. Important criteria included: minimal space requirements; fast set up times for use in confined spaces or high dose areas; the ability to cut in any direction; the ability to cut virtually any material and geometry; the minimization of secondary waste and low cutting temperature so flammable materials can be cut. It was concluded that a dry low energy mechanical cutting principle, which did not require cooling, would meet these criteria. The development program produced a low energy tool that uses the principles of a reciprocating saw together with a novel operating system that applies the principles of fuzzy logic. RASP technology can be used for virtually any cutting task and is among the safest and most versatile segmentation technologies for the in-situ processing of nuclear components. After completing a test programme in which a number of metal artefacts were segmented, RASP was been set up to cut a redundant SGHWR turbine shaft into pieces to facilitate packaging. The complete turbine assembly is a large heavy item with a steel shaft of 430mm diameter. The modular RASP framework was set up to enclose the unit and the system put to work and a hoist was set up to support the cut portion of the shaft on completion of the cut. The work was completed safely and without incident.



Author(s):  
Ningyue Zhang ◽  
Guoxu Wang ◽  
Ming Feng ◽  
Li-Zhen Fan

Solid-state batteries (SSBs) with metallic lithium (Li) anodes are regarded as the next-generation high energy and power densities energy storage devices. However, the issues of Li dendrite growth and the...



1993 ◽  
Vol 316 ◽  
Author(s):  
J. A. Floro ◽  
B. K. Kellerman ◽  
E. Chason ◽  
S. T. Picraux ◽  
D. K. Brice ◽  
...  

ABSTRACTLow energy Ar and Xe ion bombardment of Ge (001) produces large numbers of point defects on the Ge surface and in the near-surface regions. Defect concentrations on the surface are detected and quantified in real time during bombardment using in situ Reflection High Energy Electron Diffraction (RHEED). We report the energy dependence of the defect yield for 70–500 eV Ar and Xe ion bombardment, and the temperature dependence of the defect yield (defects/ion) during 200 eV ion bombardment. The defect yield drops rapidly as the substrate temperature during bombardment is varied from 175 K to 400 K. We attribute the yield reduction to surface recombination of adatoms and vacancies produced in the same collision cascade.



Author(s):  
Charles W. Allen

Irradiation effects studies employing TEMs as analytical tools have been conducted for almost as many years as materials people have done TEM, motivated largely by materials needs for nuclear reactor development. Such studies have focussed on the behavior both of nuclear fuels and of materials for other reactor components which are subjected to radiation-induced degradation. Especially in the 1950s and 60s, post-irradiation TEM analysis may have been coupled to in situ (in reactor or in pile) experiments (e.g., irradiation-induced creep experiments of austenitic stainless steels). Although necessary from a technological point of view, such experiments are difficult to instrument (measure strain dynamically, e.g.) and control (temperature, e.g.) and require months or even years to perform in a nuclear reactor or in a spallation neutron source. Consequently, methods were sought for simulation of neutroninduced radiation damage of materials, the simulations employing other forms of radiation; in the case of metals and alloys, high energy electrons and high energy ions.



Sign in / Sign up

Export Citation Format

Share Document