Effect of plastic deformation rate at room temperature on structure and mechanical properties of high-Mn austenitic Mn-Al-Si 25-3-3 type steel

2019 ◽  
Vol 1 (96) ◽  
pp. 22-31
Author(s):  
W. Borek ◽  
A. Lis ◽  
K. Gołombek ◽  
P. Sakiewicz ◽  
K. Piotrowski
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Deformation Rate ◽  
Room Temperature ◽  
Dynamic Conditions ◽  
X Ray ◽  
Type Steel ◽  
Austenitic Structure ◽  
Plastic Deformation Rate ◽  
Static Conditions

Purpose: The aim of the paper is to determine influence of plastic deformation rate at room temperature on structure and mechanical properties of high-Mn austenitic Mn-Al-Si 25-3-3 type steel tested at room temperature. Design/methodology/approach: Mechanical properties of tested steel was determined using Zwick Z100 static testing machine for testing with the deformation speed equal 0.008 s-1, and RSO rotary hammer for testing with deformation speeds of 250, 500 and 1000s-1. The microstructure evolution samples tested in static and dynamic conditions was determined in metallographic investigations using light microscopy as well as X-ray diffraction. Findings: Based on X-ray phase analysis results, together with observation using metallographic microscope, it was concluded, that the investigated high-Mn X13MnAlSiNbTi25-3-3 steel demonstrates austenitic structure with numerous mechanical twins, what agrees with TWIP effect. It was demonstrated, that raise of plastic deformation rate produces higher tensile strength UTS and higher conventional yield point YS0.2. The UTS strength values for deformation rate 250, 500 and 1000 s-1 grew by: 35, 24 and 31%, appropriately, whereas in case of YS0.2 these were: 7, 74 and 130%, accordingly, in respect to the results for the investigated steel deformed under static conditions, where UTS and YS0.2 values are 1050 MPa and 700 MPa. Opposite tendency was observed for experimentally measured uniform and total relative elongation. Homogeneous austenitic structure was confirmed by X-ray diffractometer tests. Research limitations/implications: To fully describe influence of strain rates on structure and mechanical properties, further investigations specially with using transmission electron microscope are required. Practical implications: Knowledge about obtained microstructures and mechanical properties results of tested X13MnAlSiNbTi25-3-3 steel under static and dynamic conditions can be useful for the appropriate use of this type of engineering material in machines and equipment susceptible to static or dynamic loads. Originality/value: The influence of plastic deformation at room temperature under static and dynamic conditions of new-developed high-manganese austenitic X13MnAlSiNbTi25-3-3 steels were investigated.

Influence of Aging Treatments on the Structural and Mechanical Properties of AGS Alloy Wire Cold Drawn

2018 ◽  
Vol 18 ◽  
pp. 73-78
Author(s):  
Mokhtar Bayarassou ◽  
Mosbah Zidani ◽  
Hichem Farh
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Electron Microscope ◽  
Artificial Ageing ◽  
Micro Hardness ◽  
X Ray Diffraction ◽  
Alloy Wire ◽  
X Ray ◽  
Plastic Deformation Rate ◽  
Scanning Electron

The scope of this work is to study of microstructural changes and mechanical properties during natural and artificial ageing treatment of AGS Alloy wire cold drawn with different deformation at ENICAB in Biskra. And as well to know the phase formation during different deformation of aluminum alloys wires. as well as the combined influence of the plastic deformation rate and the aging temperature. Wire section reduction shows a change in microstructure and texture. The methods of characterization used in this work are: scanning electron microscope and X-ray diffraction, micro hardness (Hv).

scholarly journals Improving of Mechanical Properties of Titanium Alloy VT23 due to Impact-Oscillatory Loading and the Use of Carbon Nano-Solution

Metals ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 652
Author(s):  
Mykola Chausov ◽  
Oleg Khyzhun ◽  
Janette Brezinová ◽  
Pavlo Maruschak ◽  
Andrii Pylypenko ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Titanium Alloy ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
High Strength ◽  
Surface Layers ◽  
Two Phase ◽  
X Ray ◽  
Alloy Vt23

Improvement in the mechanical properties of sheet two-phase high-strength titanium alloy VT23 due to impact-oscillatory loading and the use of carbon nanosolutions at room temperature was tested experimentally. It was shown that in addition to obtaining a significant increase in the initial plastic deformation of the alloy, it is possible to strengthen the surface layers of the alloy by a factor of 8.4% at a time via the impulse introduction of energy into the alloy and the use of carbon nanosolutions. Using X-ray photoelectron spectroscopy (XPS), it was first found that strengthening of the surface layers of the titanium alloy at a given load, in line with using a carbon nanosolution, leads to the formation of a mixture of titanium oxide and titanium carbide or oxycarbide of type TiO2−xCx on the surface.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

scholarly journals Low-temperature degradation resistance and plastic deformation of ATZ ceramics stabilized by CaO

2021 ◽  
Vol 2103 (1) ◽  
pp. 012075
Author(s):  
AA Dmitrievskiy ◽  
DG Zhigacheva ◽  
VM Vasyukov ◽  
PN Ovchinnikov
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Plastic Deformation ◽  
Compressive Strength ◽  
Phase Composition ◽  
Low Temperature ◽  
Uniaxial Compression ◽  
Calcium Oxide ◽  
Tetragonal Phase ◽  
Room Temperature

Abstract In this work, the phase composition (relative fractions of monoclinic m-ZrO2, tetragonal t-ZrO2, and cubic c-ZrO2 phases) and mechanical properties (hardness, fracture toughness, compressive strength) of alumina toughened zirconia (ATZ) ceramics, with an addition of silica were investigated. Calcium oxide was used as a stabilizer for the zirconia tetragonal phase. It was shown that CaO-ATZ+SiO2 ceramics demonstrate increased resistance to low-temperature degradation. The plasticity signs at room temperature were found due to the SiO2 addition to CaO-ATZ ceramics. A yield plateau appears in the uniaxial compression diagram at 5 mol. % SiO2 concentration. It is hypothesized that discovered plasticity is due to the increased t→m transformability.

Effect of Hot Forging and Different Cooling Rates on the Microstructure, Mechanical Properties of Carbon Steel Containing 0.8 and 1.2Al

2014 ◽  
Vol 622-623 ◽  
pp. 174-178
Author(s):  
Ahmed Ismail Zaky Farahat ◽  
Mohamed Kamal Elfawkhry
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Mechanical Testing ◽  
Room Temperature ◽  
Induction Furnace ◽  
Hot Forging ◽  
X Ray Diffraction ◽  
Cooling Rates ◽  
X Ray ◽  
Sem Microstructure

Two alloys of steel containing nominally 0.45C-1.0Si-2.0Mn-0.8Al and 1.2Al were cast in open air induction furnace. Dilatation testing was carried out to recognize the effect on Aluminum on the different critically transformation temperatures. The alloys were hot forged at 1200°C and then subjected to different cooling rates. Mechanical testing was carried out at room temperature. Optical and SEM microstructure were observed. X-ray diffraction was conducted to observe the microstructure constituents.

Effect of Nitrogen Addition on Mechanical Property of Ti-Cr-Sn Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 2126-2129 ◽  
Author(s):  
Yuichi Nakahira ◽  
Tomonari Inamura ◽  
Hiroyasu Kanetaka ◽  
Shuichi Miyazaki ◽  
Hideki Hosoda
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Nitrogen Addition ◽  
N Addition ◽  
X Ray Diffraction ◽  
Solution Hardening ◽  
X Ray ◽  
Bcc Phase ◽  
Cold Workability

Effect of nitrogen (N) addition on mechanical properties of Ti-Cr-Sn alloy was investigated in this study. Ti-7mol%Cr-3mol%Sn was selected and less than 0.5wt% of N were systematically added. The alloys were characterized by optical microscopy, X-ray diffraction analysis and tensile tests at room temperature. The apparent phase was β (bcc) phase, whereas the presence of precipitates was confirmed in 0.5wt%N-added alloy only which did not exhibit sufficient cold workability. The grain size was not largely affected by N addition being less than 0.5wt%. Tensile tests revealed that less than 0.5wt%N addition improves the strength which is due to the solution hardening by interstitial N atoms.

Superplasticity of Aerospace 7075 (Al-Zn-Mg-Cu) Aluminium Alloy Obtained by Severe Plastic Deformation

2018 ◽  
Vol 385 ◽  
pp. 39-44 ◽  
Author(s):  
Fernando Carreño ◽  
Oscar A. Ruano
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Aluminium Alloy ◽  
Room Temperature ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
Aerospace Applications ◽  
Boundary Sliding ◽  
Processing Stress

The 7075 (Al-Zn-Mg-Cu) aluminium alloy is the reference alloy for aerospace applications due to its specific mechanical properties at room temperature, showing excellent tensile strength and sufficient ductility. Formability at high temperature can be improved by obtaining superplasticity as a result of fine, equiaxed and highly misoriented grains prone to deform by grain boundary sliding (GBS). Different severe plastic deformation (SPD) processing routes such as ECAP, ARB, HPT and FSP have been considered and their effect on mechanical properties, especially at intermediate to high temperatures, are studied. Refined grains as fine as 100 nm and average misorientations as high as 39o allow attainment of high strain rate superplasticity (HSRSP) at lower than usual temperatures (250-300oC). It is shown that increasing misorientations are obtained with increasing applied strain, and increasing grain refinement is obtained with increasing processing stress. Thus, increasing superplastic strains at higher strain rates, lower stresses and lower temperatures are obtained with increasing processing strain and, specially, processing stress.

Effects of Extrusion on the Mechanical Properties and Damping Capacity of Mg-1.8Cu-0.5Mn Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 257-260 ◽  
Author(s):  
Zhen Yan Zhang ◽  
Li Ming Peng ◽  
Xiao Qin Zeng ◽  
Lin Du ◽  
Lan Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Damping Capacity ◽  
X Ray Diffraction ◽  
Dynamic Mechanical Analyzer ◽  
X Ray ◽  
Solute Atoms

Effects of extrusion on mechanical properties and damping capacity of Mg-1.8wt.%Cu -0.5wt.%Mn (MCM1805) alloy have been investigated. Tensile tests and dynamic mechanical analyzer were respectively used to measure tensile properties and damping capacity at room temperature of as-cast and as-extruded MCM1805 alloy. The microstructure was studied using optical microscope, X-ray diffraction and scanning electron microscope with an energy dispersive X-ray spectrometer. Granato-Lücke model was used to explain the influences of extrusion on damping capacity of MCM1805 alloy. The results showed that extrusion dramatically decreases the grain size but has little influence on phase composition and solute atoms concentration of MCM1805 alloy, and the grain refinement was the dominant reason for the obvious increase of tensile properties and decrease of internal friction of MCM1805 alloy.

Platelet Adhesion Study and Characteristic of Hydrogenated Carbon Films Synthesized by PIII-D

2005 ◽  
Vol 288-289 ◽  
pp. 323-326 ◽  
Author(s):  
Feng Wen ◽  
Nan Huang ◽  
H. Sun ◽  
Ping Yang ◽  
Jin Wang
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Raman Spectra ◽  
Room Temperature ◽  
Platelet Adhesion ◽  
Carbon Films ◽  
Photoelectron Spectra ◽  
X Ray ◽  
Composition And Structure ◽  
Amorphous Hydrogenated Carbon

Amorphous hydrogenated carbon (a-C:H) thin films were deposited on silicon wafers and Ti6Al4V substrate using plasma ion immersion implantation and deposition (PIII-D) at room temperature (R.T.). The composition and structure of a-C:H films were employed by X-ray photoelectron spectra (XPS) and Raman spectra. Nano-indenter tests measured the hardness of the films. In addition, wettability and bloodcompatibility were investigated. In this paper, the effects of hydrogen content on structure, mechanical properties, surface wettability and haemocompatibility were discussed.

Sign in / Sign up

Export Citation Format

Share Document