Effects of Extrusion on the Mechanical Properties and Damping Capacity of Mg-1.8Cu-0.5Mn Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 257-260 ◽  
Author(s):  
Zhen Yan Zhang ◽  
Li Ming Peng ◽  
Xiao Qin Zeng ◽  
Lin Du ◽  
Lan Ma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Optical Microscope ◽  
Damping Capacity ◽  
X Ray Diffraction ◽  
Dynamic Mechanical Analyzer ◽  
X Ray ◽  
Solute Atoms

Effects of extrusion on mechanical properties and damping capacity of Mg-1.8wt.%Cu -0.5wt.%Mn (MCM1805) alloy have been investigated. Tensile tests and dynamic mechanical analyzer were respectively used to measure tensile properties and damping capacity at room temperature of as-cast and as-extruded MCM1805 alloy. The microstructure was studied using optical microscope, X-ray diffraction and scanning electron microscope with an energy dispersive X-ray spectrometer. Granato-Lücke model was used to explain the influences of extrusion on damping capacity of MCM1805 alloy. The results showed that extrusion dramatically decreases the grain size but has little influence on phase composition and solute atoms concentration of MCM1805 alloy, and the grain refinement was the dominant reason for the obvious increase of tensile properties and decrease of internal friction of MCM1805 alloy.

Effects of Cu on Microstructure, Mechanical Properties and Damping Capacity of As-Cast Mg-3%Ni Alloy

2012 ◽  
Vol 463-464 ◽  
pp. 52-57 ◽  
Author(s):  
Shu Qun Chen ◽  
Xuan Pu Dong ◽  
Xiao Qing Xiong ◽  
Rong Ma ◽  
Zi Tian Fan
Keyword(s):  
Mechanical Properties ◽  
High Strain ◽  
Strain Range ◽  
Tensile Tests ◽  
Eutectic Phase ◽  
Damping Capacity ◽  
X Ray Diffraction ◽  
Dynamic Mechanical Analyzer ◽  
X Ray ◽  
Ni Alloy

The effects of Cu addition on microstructure, mechanical properties and damping capacity of Mg-3%Ni based alloy were investigated by using tensile tests, X-ray diffraction, scanning electron microscope and dynamic mechanical analyzer. The results show that Cu addition could reduce the size of -Mg dendrites and a new binary phase Mg2Cu can be identified, which mostly distributes among the inter-dendrites in the form of typical lamellar-like eutectic microstructure and improve the mechanical properties. In low strain amplitude, with the increase of Cu addition, the damping capacities of Cu contained alloys change little, while in high strain range, the internal friction values decrease gradually with the grain refinement and increasing content of eutectic phase.

Effect of Nitrogen Addition on Mechanical Property of Ti-Cr-Sn Alloy

2010 ◽  
Vol 654-656 ◽  
pp. 2126-2129 ◽  
Author(s):  
Yuichi Nakahira ◽  
Tomonari Inamura ◽  
Hiroyasu Kanetaka ◽  
Shuichi Miyazaki ◽  
Hideki Hosoda
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Tensile Tests ◽  
Nitrogen Addition ◽  
N Addition ◽  
X Ray Diffraction ◽  
Solution Hardening ◽  
X Ray ◽  
Bcc Phase ◽  
Cold Workability

Effect of nitrogen (N) addition on mechanical properties of Ti-Cr-Sn alloy was investigated in this study. Ti-7mol%Cr-3mol%Sn was selected and less than 0.5wt% of N were systematically added. The alloys were characterized by optical microscopy, X-ray diffraction analysis and tensile tests at room temperature. The apparent phase was β (bcc) phase, whereas the presence of precipitates was confirmed in 0.5wt%N-added alloy only which did not exhibit sufficient cold workability. The grain size was not largely affected by N addition being less than 0.5wt%. Tensile tests revealed that less than 0.5wt%N addition improves the strength which is due to the solution hardening by interstitial N atoms.

Influence of RE on Microstructure and Mechanical Properties of Mg-Li-Al Alloys

2007 ◽  
Vol 546-549 ◽  
pp. 211-216 ◽  
Author(s):  
Bin Liu ◽  
M.L. Zhang ◽  
Zhong Yi Niu
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Melting Furnace ◽  
Optical Microscope ◽  
Al Alloys ◽  
X Ray Diffraction ◽  
Vacuum Melting ◽  
X Ray ◽  
Electronic Microscope ◽  
Cast Microstructure

A series of alloys were designed and prepared using vacuum melting furnace. The as-cast microstructure and phase compositions of these alloys were characterized by optical microscope, X-ray diffraction (XRD) and scanning electronic microscope (SEM). The hardness and mechanical properties of alloys at room temperature were measured as well. The results show that the addition of RE leads to the formation of intermetallic Al3La distributed within grain boundaries. The intermetallic compound with oriented structure impedes grain growth, and refines the grain. The strength and the hardness of the alloys increase with the increase of the RE content in the range of 0.2-0.8 wt %.

Effects of Sb on Microstructure and Mechanical Properties of Mg-5.5Al-1.2Y Alloy

2011 ◽  
Vol 194-196 ◽  
pp. 1374-1377
Author(s):  
Chang Qing Li ◽  
Quan an Li ◽  
Xing Yuan Zhang ◽  
Qing Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Room Temperature ◽  
Optical Microscope ◽  
High Melting ◽  
X Ray Diffraction ◽  
High Melting Point ◽  
X Ray ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of aged Mg-5.5Al-1.2Y magnesium alloy with Sb addition are investigated by optical microscope, SEM and X-ray diffraction analyzer. The results show that with proper content of Sb addition,the microstructure of Mg-5.5Al-1.2Y magnesium alloy is refined obviously and high melting point intermetallic compounds Sb3Y5 and Mg3Sb2 are formed. Meanwhile, the β-Mg17Al12 phase is more distributed. With the increase of Sb addition, the mechanical properties of the alloy at room and elevated temperature increase at first, and then decrease. When the content of Sb is up to 0.5%, the values of tensile strength and elongation at room temperature, 150ºC and 175ºC are up to their maxima synchronously, 241MPa /16.84%, 198MPa/20.27.86% and 169MPa/21.21% respectively.

Physical and Mechanical Properties of Cement Paste Were Used Partially with Fly Ash and Kaolin Waste

2017 ◽  
Vol 866 ◽  
pp. 199-203
Author(s):  
Chidchanok Chainej ◽  
Suparut Narksitipan ◽  
Nittaya Jaitanong
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Partial Replacement ◽  
X Ray Diffraction ◽  
X Ray ◽  
Lime Water ◽  
Diffraction Patterns ◽  
Iron Mold

The aims of this research were study the microstructures and mechanical properties for partial replacement of cement with Fly ash (FA) and kaolin waste (KW). Ordinary Portland cement were partially replaced with FA and KW in the range of 25-35% and 10-25% by weight of cement powder. The kaolin waste was ground for 180 minutes before using. The specimen was packing into an iron mold which sample size of 5×5×5 cm3. Then, the specimens were kept at room temperature for 24 hours and were moist cured in the incubation lime water bath at age of 3 days. After that the specimens were dry cured with plastic wrap at age of 3, 7, 14 and 28 days. After that the compounds were examined by x-ray diffraction patterns (XRD) and the microstructures were examined by scanning electron microscopy (SEM). The compressive strength was then investigated.

Spark Plasma Sintering of Ti-4.5Al-3V-2Fe-2Mo (SP-700)

2010 ◽  
Vol 654-656 ◽  
pp. 819-822
Author(s):  
Genki Kikuchi ◽  
Hiroshi Izui ◽  
Yuya Takahashi ◽  
Shota Fujino
Keyword(s):  
Spark Plasma Sintering ◽  
Room Temperature ◽  
Volume Fraction ◽  
Titanium Boride ◽  
Tensile Tests ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Tib2 Particles

In this study, we focused on the sintering performance of Ti-4.5Al-3V-2Mo-2Fe (SP-700) and mechanical properties of SP-700 reinforced with titanium boride (TiB/SP-700) fabricated by spark plasma sintering (SPS). TiB whiskers formed in titanium by a solid-state reaction of titanium and TiB2 particles were analyzed with scanning electron microscopy and X-ray diffraction. The TiB/SP-700 was sintered at temperatures of 1073, 1173, and 1273 K and a pressure of 70 MPa for 10, 30, and 50 min. The volume fraction of TiB ranged from 1.7 vol.% to 19.9 vol.%. Tensile tests of TiB/SP-700 were conducted at room temperature, and the effect of TiB volume fraction on the tensile properties was investigated.

scholarly journals Microstructural Characterization and Mechanical Properties of L-PBF Processed 316 L at Cryogenic Temperature

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5856
Author(s):  
Pragya Mishra ◽  
Pia Åkerfeldt ◽  
Farnoosh Forouzan ◽  
Fredrik Svahn ◽  
Yuan Zhong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cryogenic Temperature ◽  
Room Temperature ◽  
Mechanical Performance ◽  
Microstructural Characterization ◽  
Tensile Tests ◽  
Phase Changes ◽  
X Ray Diffraction ◽  
Temperature Range ◽  
Aerospace Applications

Laser powder bed fusion (L-PBF) has attracted great interest in the aerospace and medical sectors because it can produce complex and lightweight parts with high accuracy. Austenitic stainless steel alloy 316 L is widely used in many applications due to its good mechanical properties and high corrosion resistance over a wide temperature range. In this study, L-PBF-processed 316 L was investigated for its suitability in aerospace applications at cryogenic service temperatures and the behavior at cryogenic temperature was compared with room temperature to understand the properties and microstructural changes within this temperature range. Tensile tests were performed at room temperature and at −196 °C to study the mechanical performance and phase changes. The microstructure and fracture surfaces were characterized using scanning electron microscopy, and the phases were analyzed by X-ray diffraction. The results showed a significant increase in the strength of 316 L at −196 °C, while its ductility remained at an acceptable level. The results indicated the formation of ε and α martensite during cryogenic testing, which explained the increase in strength. Nanoindentation revealed different hardness values, indicating the different mechanical properties of austenite (γ), strained austenite, body-centered cubic martensite (α), and hexagonal close-packed martensite (ε) formed during the tensile tests due to mechanical deformation.

Effect of Hot Forging and Different Cooling Rates on the Microstructure, Mechanical Properties of Carbon Steel Containing 0.8 and 1.2Al

2014 ◽  
Vol 622-623 ◽  
pp. 174-178
Author(s):  
Ahmed Ismail Zaky Farahat ◽  
Mohamed Kamal Elfawkhry
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Mechanical Testing ◽  
Room Temperature ◽  
Induction Furnace ◽  
Hot Forging ◽  
X Ray Diffraction ◽  
Cooling Rates ◽  
X Ray ◽  
Sem Microstructure

Two alloys of steel containing nominally 0.45C-1.0Si-2.0Mn-0.8Al and 1.2Al were cast in open air induction furnace. Dilatation testing was carried out to recognize the effect on Aluminum on the different critically transformation temperatures. The alloys were hot forged at 1200°C and then subjected to different cooling rates. Mechanical testing was carried out at room temperature. Optical and SEM microstructure were observed. X-ray diffraction was conducted to observe the microstructure constituents.

Microstructure characterization and evaluation of mechanical properties of stir rheocast AA2024/TiB2 composite

2019 ◽  
Vol 54 (7) ◽  
pp. 981-997
Author(s):  
Semegn Cheneke ◽  
D Benny Karunakar
Keyword(s):  
Mechanical Properties ◽  
Dendritic Structure ◽  
Optical Microscope ◽  
X Ray Diffraction ◽  
Globular Structure ◽  
Cast Sample ◽  
X Ray ◽  
Weight Percentage ◽  
The Matrix ◽  
Fractured Surface

In this research, microstructure and mechanical properties of stir rheocast AA2024/TiB2 metal matrix composite have been investigated. The working temperature was 640℃, which was the selected semisolid temperature that corresponds to 40% of the solid fraction. Two weight percentage, 4 wt%, and 6 wt% of the TiB2 reinforcements were added to the matrix. The field emission scanning electron microscope micrographs of the developed composites showed a uniform distribution of the particles in the case of the 2 wt% and 4 wt% of the reinforcements. However, the particles agglomerated as the weight percentages of the reinforcement increases to 6%. The optical microscope of the liquid cast sample showed the dendritic structure, whereas the rheocast samples showed a globular structure. The X-ray diffraction analysis confirmed the distribution of the reinforcements in the matrix and the formation of some intermetallic compounds. Mechanical properties significantly improved by the addition of the reinforcements in the matrix. An increase in tensile strength of 13.3%, 40%, 28%, and 5% was achieved for the unreinforced rheocast sample, 2 wt%, 4 wt%, and 6 wt% reinforced rheocast samples respectively, compared to the liquid cast sample. An increase in 20% of hardness was attained for the composite with 2 wt% TiB2 compared to the liquid cast sample. According to the fractography analysis, small dimples were observed on the fractured surface of the unreinforced rheocast sample, whereas small and large voids were dominant on the fractured surface of the 2 wt% composite, which shows the ductile fracture mode.

Structure and properties of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/poly(L-lactic acid) quasi core/sheath melt-electrospun microfibers

2018 ◽  
Vol 89 (9) ◽  
pp. 1770-1781 ◽  
Author(s):  
Huaizhong Xu ◽  
Benedict Bauer ◽  
Masaki Yamamoto ◽  
Hideki Yamane
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Diffraction Patterns

A facile route was proposed to fabricate core–sheath microfibers, and the relationships among processing parameters, crystalline structures and the mechanical properties were investigated. The compression molded poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH)/poly(L-lactic acid) (PLLA) strip enhanced the spinnability of PHBH and the mechanical properties of PLLA as well. The core–sheath ratio of the fibers was determined by the prefab strip, while the PLLA sheath component did not completely cover the PHBH core component due to the weak interfacial tension between the melts of PHBH and PLLA. A rotational target was applied to collect aligned fibers, which were further drawn in a water bath. The tensile strength and the modulus of as-spun and drawn fibers increased with increasing the take-up velocities. When the take-up velocity was above 500 m/min, the jet became unstable and started to break up at the tip of the Taylor cone, decreasing the mechanical properties of the fibers. The drawing process facilitated the crystallization of PLLA and PHBH, and the tensile strength and the modulus increased linearly with the increasing the draw ratio. The crystal information displayed from wide-angle X-ray diffraction patterns and differential scanning calorimetry heating curves supported the results of the tensile tests.

Sign in / Sign up

Export Citation Format

Share Document