scholarly journals Effects of Specific Fuel Consumption and Exhaust Emissions of Four Stroke Diesel Engine with CuO/Water Nanofluid as Coolant

2017 ◽  
Vol 64 (1) ◽  
pp. 111-121 ◽  
Author(s):  
S. Senthilraja ◽  
KCK. Vijayakumar ◽  
R. Gangadevi
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Load Condition ◽  
Exhaust Emissions ◽  
Cuo Nanoparticles ◽  
Specific Fuel Consumption ◽  
Gas Temperature ◽  
Step Method ◽  
Series Of Experiments ◽  
Exhaust Gas Temperature

Abstract This article reports the effects of CuO/water based coolant on specific fuel consumption and exhaust emissions of four stroke single cylinder diesel engine. The CuO nanoparticles of 27 nm were used to prepare the nanofluid-based engine coolant. Three different volume concentrations (i.e 0.05%, 0.1%, and 0.2%) of CuO/water nanofluids were prepared by using two-step method. The purpose of this study is to investigate the exhaust emissions (NOx), exhaust gas temperature and specific fuel consumption under different load conditions with CuO/water nanofluid. After a series of experiments, it was observed that the CuO/water nanofluids, even at low volume concentrations, have a significant influence on exhaust emissions. The experimental results revealed that, at full load condition, the specific fuel consumption was reduced by 8.6%, 15.1% and 21.1% for the addition of 0.05%, 0.1% and 0.2% CuO nanoparticles with water, respectively. Also, the emission tests were concluded that 881 ppm, 853 ppm and 833 ppm of NOx emissions were observed at high load with 0.05%, 0.1% and 0.2% volume concentrations of CuO/water nanofluids, respectively.

scholarly journals An Experimental Study on the Performance Characteristics of a Diesel Engine Fueled with ULSD-Biodiesel Blends

2020 ◽  
Vol 10 (2) ◽  
pp. 183-190
Author(s):  
Viet Dung Tran ◽  
Anh Tuan Le ◽  
Anh Tuan Hoang
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Cooling System ◽  
Specific Fuel Consumption ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature ◽  
Low Sulfur

As a rule, the highest permissible sulfur content in the marine fuel must drop below 0.5% from 1 January 2020 for global fleets. As such, ships operating in emission control areas must use low sulfur or non-sulfur fuel to limit sulfur emissions as a source of acid rain. However, that fact has revealed two challenges for the operating fleet: the very high cost of ultra-low sulfur diesel (ULSD) and the installation of the fuel conversion system and the ULSD cooling system. Therefore, a solution that blends ULSD and biodiesel (BO) into a homogeneous fuel with properties equivalent to that of mineral fuels is considered to be significantly effective. In the current work, an advanced ultrasonic energy blending technology has been applied to assist in the production of homogeneous ULSD-BO blends (ULSD, B10, B20, B30, and B50 with blends of coconut oil methyl ester with ULSD of 10%, 20%, 30% and 50% by volume) which is supplied to a small marine diesel engine on a dynamo test bench to evaluate the power and torque characteristics, also to consider the effect of BO fuel on specific fuel consumption exhaust gas temperature and brake thermal efficiency. The use of the ultrasonic mixing system has yielded impressive results for the homogeneous blend of ULSD and BO, which has contributed to improved combustion quality and thermal efficiency. The results have shown that the power, torque, and the exhaust gas temperature, decrease by approximately 9%, 2%, and 4% respectively with regarding the increase of the blended biodiesel rate while the specific fuel consumption and brake thermal efficiency tends to increase of around 6% and 11% with those blending ratios.

The Comparative Trail Research on the Performance of a Diesel Engine Fuelled with Diesel Fuel and Biodiesel/Diesel Blended Fuel

2011 ◽  
Vol 142 ◽  
pp. 103-106
Author(s):  
Wen Ming Cheng ◽  
Hui Xie ◽  
Gang Li
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Brake Thermal Efficiency ◽  
Series Of Experiments ◽  
Blended Fuel ◽  
Load Conditions

This paper discusses the brake specific fuel consumption and brake thermal efficiency of a diesel engine using cottonseed biodiesel blended with diesel fuel. A series of experiments were conducted for the various blends under varying load conditions at a speed of 1500 rpm and 2500 rpm and the results were compared with the neat diesel. From the results, it is found that the brake specific fuel consumption of cottonseed biodiesel is slightly higher than that of diesel fuel at different engine loads and speeds, with this increase being higher the higher the percentage of the biodiesel in the blend. And the brake thermal efficiency of cottonseed biodiesel is nearly similar to that of diesel fuel at different engine loads and speeds. From the investigation, it is concluded that cottonseed biodiesl can be directly used in diesel engines without any modifications, at least in small blending ratios.

scholarly journals Study of the working process of a diesel engine with modified fuel

2021 ◽  
Vol 2131 (2) ◽  
pp. 022073
Author(s):  
G Yur ◽  
E Nosonova
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Numerical Study ◽  
Gas Temperature ◽  
Vapor Bubbles ◽  
Fuel Gas ◽  
Operation Process ◽  
Study Results ◽  
Exhaust Fumes ◽  
Exhaust Gas Temperature

Abstract The research objective is to reduce specific fuel consumption and emissions of exhaust fume pollutants. Specifically treated (modified) fuel is used to comprehensively improve the economic and environmental performance of the diesel operation process. Fuel treatment was carried out at a pilot plant using the process of fuel gas cavitation. During processing, high-molecular fuel compounds were broken down and the fuel was saturated with gas-vapor bubbles. The description of the pilot unit is given. The characteristics of the base distillate and modified fuel are studied. A mathematical model and the numerical study results of the fuel droplet development containing vapor-gas bubbles are presented. An experimental study of the work process in a 10.5/12 H diesel engine single-cylinder compartment when operating on various fuels was carried out. Diesel tests have shown that when using modified fuel, the specific indicative fuel consumption has decreased by 5-7 per g / kWh, the exhaust gas temperature has decreased by 5-8 degrees, the concentration of nitrogen oxides in the exhaust fumes has decreased by 32-46 ppm, the concentration of total hydrocarbons has decreased by 9-14 ppm, the smoke content has decreased by 1.2-1.7 times.

scholarly journals Investigations on Performance and Emission Characteristics of Diesel Engine with Biodiesel (Jatropha Oil) and Its Blends

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Amar Pandhare ◽  
Atul Padalkar
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Brake Thermal Efficiency ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Exhaust Gas Temperature ◽  
Load Conditions

This paper presents the performance of biodiesel blends in a single-cylinder water-cooled diesel engine. All experiments were carried out at constant speed 1500 rpm and the biodiesel blends were varied from B10 to B100. The engine was equipped with variable compressions ratio (VCR) mechanism. For 100% Jatropha biodiesel, the maximum fuel consumption was 15% higher than that of diesel fuel. The brake thermal efficiency for biodiesel and its blends was found to be slightly higher than that of diesel at various load conditions. The increase in specific fuel consumption ranged from 2.75% to 15% for B10 to B100 fuels. The exhaust gas temperature increased with increased biodiesel blend. The highest exhaust gas temperature observed was 430°C with biodiesel for load conditions 1.5 kW, 2.5 kW, and 3.5 kW, where as for diesel the maximum exhaust gas temperature was 440°C. The CO2emission from the biodiesel fuelled engine was higher by 25% than diesel fuel at full load. The CO emissions were lower with Jatropha by 15%, 13%, and 13% at 1.5 kW, 2.5 kW, and 3.5 kW load conditions, respectively. TheNOxemissions were higher by 16%, 19%, and 20% at 1.5 kW, 2.5 kW, and 3.5 kW than that of the diesel, respectively.

scholarly journals Performance, Emissions and Durability Studies on Diesel Engine Fuelled with a Preheated Raw Microalgal Oil

Proceedings ◽  
2020 ◽  
Vol 58 (1) ◽  
pp. 4
Author(s):  
Hassan M Attar ◽  
Dawei Wu ◽  
Adam P Harvey
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Specific Fuel Consumption ◽  
Critical Parameters ◽  
Significant Finding ◽  
Brake Specific Fuel Consumption ◽  
Gas Temperature ◽  
Durability Test ◽  
Microalgal Oil ◽  
Brake Power

Preheated Schizochytrium sp. raw microalgae oil (MAO) was evaluated as a fuel in a single-cylinder four-stroke diesel engine to produce a comparative study of MAO and diesel oil (DO) critical parameters. In particular, brake power, brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), in-cylinder pressure (CP), exhaust gas temperature (EGT), both nitrogen oxides (NOx) and carbon monoxide (CO) emissions were investigated. Additionally, an engine durability test for longevity was undertaken over a 30-h period, using raw MAO as the fuel. The study demonstrated that the preheated MAO could be successfully used in a diesel engine smoothly. The use of MAO reduced the engine brake power by 26% and increased brake-specific fuel consumption by 20%. The most significant finding from this research study is that there was a significant reduction in NOx and CO emission by 42% and 60% when using raw MAO, respectively. Therefore, these findings demonstrate that algae oil is a highly credible fuel for use in diesel engines and offers a promising solution to diesel engine emissions.

scholarly journals Computational model of the fuel consumption and exhaust temperature of a heavy duty diesel engine using MATLAB/SIMULINK

2020 ◽  
Vol 45 (4) ◽  
pp. 51-70
Author(s):  
Ifeanyi Dilibe
Keyword(s):  
Control System ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Exhaust Gas ◽  
Electronic Control ◽  
Gas Temperature ◽  
Brake Torque ◽  
Exhaust Temperature ◽  
Electronic Control System ◽  
Exhaust Gas Temperature

A model of a diesel engine and its electronic control system was developed to investigate the engine behaviour in a vehicle simulation environment. The modelled quantities were brake torque, fuel consumption and exhaust gas temperature and were based on engine speed and pedal position. In order to describe these outputs the inlet air flow and boost pressure were also modelled and used as inner variables. The model was intended to be implemented on board a vehicle in a control unit which had limited computational performance. To keep the model as computationally efficient as possible the model basically consists of look-up tables and polynomials. First order systems were used to describe the dynamics of air flow and exhaust temperature. The outputs enable gear shift optimization over three variables, torque for vehicle acceleration, fuel consumption for efficiency and exhaust temperature to maintain high efficiency in the exhaust after treatment system. The engine model captures the low frequent dynamics of the modelled quantities in the closed loop of the engine and its electronic control system. The model only consists of three states, one for the pressure build up in the intake manifold and two states for modelling the exhaust temperature. The model was compared to measured data from an engine test cell (as got in INNOSON NIG. LTD.) and the mean absolute relative error were lower than 6.8%, 7.8% and 5.8% for brake torque, fuel consumption and exhaust gas temperature respectively. These results were considered good given the simplicity of the model.

The Performance of a Common Rail Diesel Engine Fueled with Different Blending Ratio of Biodiesels at Different Altitudes

2013 ◽  
Vol 860-863 ◽  
pp. 1685-1689
Author(s):  
Ze Fei Tan ◽  
Li Zhong Shen ◽  
De Cai Jin ◽  
Yang Wen Bin Ou
Keyword(s):  
High Pressure ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Common Rail ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Gas Temperature ◽  
Engine Power ◽  
High Pressure Common Rail

To study the effect of the biodiesel on the performance of the high pressure common rail diesel engine performance, a experiment is conducted about the high pressure common rail diesel engine uses diesel fuel and different blending ratio of biodiesels. The results show that with the rising of the altitude, the engine power and the brake specific fuel consumption reduce, exhaust gas temperature increases; At the same altitude, the engine fueled with different blending ratio of bio-diesel has higher brake specific fuel consumption in comparison with fueled engine, but it has lower power, with the increase in bio-diesel blending ratio, engine power, fuel consumption increase.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Numerical and Experimental Study on the Impact of Mild Cold EGR on Exhaust Emissions in a Biodiesel Fueled Diesel Engine

2021 ◽  
Author(s):  
Alex Oliveira ◽  
Junfeng Yang ◽  
Jose Sodre
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Exhaust Emissions ◽  
Pollutant Emissions ◽  
Cylinder Pressure ◽  
Nox Formation ◽  
Ratio Distribution ◽  
Engine Model ◽  
Gas Recirculation ◽  
The Impact

Abstract This work evaluated the effect of cooled exhaust gas recirculation (EGR) on fuel consumption and pollutant emissions from a diesel engine fueled with B8 (a blend of biodiesel and Diesel 8:92%% by volume), experimentally and numerically. Experiments were carried out on a Diesel power generator with varying loads from 5 kW to 35 kW and 10% of cold EGR ratio. Exhaust emissions (e.g. THC, NOX, CO etc.) were measured and evaluated. The results showed mild EGR and low biodiesel content have minor impact of engine specific fuel consumption, fuel conversion efficiency and in-cylinder pressure. Meanwhile, the combination of EGR and biodiesel reduced THC and NOX up to 52% and 59%, which shows promising effect on overcoming the PM-NOX trade-off from diesel engine. A 3D CFD engine model incorporated with detailed biodiesel combustion kinetics and NOx formation kinetics was validated against measured in-cylinder pressure, temperature and engine-out NO emission from diesel engine. This valid model was then employed to investigate the in-cylinder temperature and equivalence ratio distribution that predominate NOx formation. The results showed that the reduction of NOx emission by EGR and biodiesel is obtained by a little reduction of the local in-cylinder temperature and, mainly, by creating comparatively rich combusting mixture.

Sign in / Sign up

Export Citation Format

Share Document