Theoretical Prediction of Motions of High-Speed Planing Boats in Waves

1978 ◽  
Vol 22 (03) ◽  
pp. 140-169
Author(s):  
Milton Martin
Keyword(s):  
High Speed ◽  
Damping Ratio ◽  
Nonlinear Effects ◽  
Theoretical Method ◽  
Valuable Insight ◽  
Response Characteristics ◽  
Theoretical Predictions ◽  
Response Amplitude Operators ◽  
Phase Angles ◽  
Good Agreement

A theoretical method is derived for predicting the linearized response characteristics of constant deadrise high-speed planing boats in head and following waves. Comparisons of the theoretical predictions of the pitch and heave response amplitude operators and phase angles with existing experimental data show reasonably good agreement for a wide variety of conditions of interest. It appears that nonlinear effects are more severe at a speed to length ratio of 6 than of, say, 4 or less, principally because of the reduction of the damping ratio of the boat with increasing speed, and the consequent increase in motions in the vicinity of the resonant encounter frequency. However, it is concluded that the linear theory can provide a simple and fast means of determining the effect of various parameters such as trim angle, deadrise, loading, and speed on the damping, natural frequency, and linearized response in waves, and that this can furnish valuable insight into the actual boat dynamics, even though the accurate predictions of large motions and peak accelerations would require a nonlinear analysis.

scholarly journals Theoretical Determination of Porpoising Instability of High-Speed Planing Boats

1978 ◽  
Vol 22 (01) ◽  
pp. 32-53 ◽  
Author(s):  
Milton Martin
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Natural Frequencies ◽  
Theoretical Method ◽  
Theoretical Determination ◽  
Damping Characteristics ◽  
Wide Range ◽  
Theoretical Predictions ◽  
Good Agreement

A theoretical method is derived for predicting trim angle and speed coefficient at the inception of propoising of prismatic planing hulls. Although equations are derived for the surge, pitch, and heave degrees of freedom, it is seen that the effect of surge is small at ordinary operating trim angles. Comparisons of theoretical predictions with existing experimental data on coupled pitch and heave porpoising show reasonably good agreement for a wide range of speed coefficients, load coefficients, and deadrise angles. The theory may also be used for estimating the natural frequencies and damping characteristics of prismatic hulls in the stable, high-speed planing range.

Some Limitations in Applying Classical EHD Film Thickness Formulas to a High-Speed Bearing

1981 ◽  
Vol 103 (2) ◽  
pp. 295-301 ◽  
Author(s):  
J. J. Coy ◽  
E. V. Zaretsky
Keyword(s):  
Film Thickness ◽  
High Speed ◽  
Heating Effects ◽  
Theoretical Predictions ◽  
Traction Fluid ◽  
Shear Heating ◽  
Thickness Measurements ◽  
Inner Race ◽  
Maximum Stresses ◽  
Good Agreement

Elastohydrodynamic film thickness was measured for a 20-mm ball bearing using the capacitance technique. The bearing was thrust loaded to 90, 448, and 778 N (20, 100, and 175 lb). The corresponding maximum stresses on the inner race were 1.28, 2.09, and 2.45 GPa (185,000, 303,000, and 356,000 psi). Test speeds ranged from 400 to 14,000 rpm. Film thickness measurements were taken with four different lubricants: (a) synthetic paraffinic, (b) synthetic paraffinic with additives, (c) neopentylpolyol (tetra) ester meeting MIL-L-23699A specifications, and (d) synthetic cycloaliphatic hydrocarbon traction fluid. The test bearing was mist lubricated. Test temperatures were 300, 338, and 393 K. The measured results were compared to theoretical predictions using the formulae of Grubin, Archard and Cowking, Dowson and Higginson, and Hamrock and Dowson. There was good agreement with theory at low dimensionless speed, but the film was much smaller than theory predicts at higher speeds. This was due to kinematic starvation and inlet shear heating effects. Comparisons with Chiu’s theory on starvation and Cheng’s theory on inlet shear heating were made.

Stability of Water-Lubricated, Hydrostatic, Conical Bearings With Spiral Grooves for High-Speed Spindles

2001 ◽  
Vol 124 (2) ◽  
pp. 398-405 ◽  
Author(s):  
S. Yoshimoto ◽  
S. Oshima ◽  
S. Danbara ◽  
T. Shitara
Keyword(s):  
High Speed ◽  
Water Pressure ◽  
Rotating Shaft ◽  
Pressurized Water ◽  
High Speeds ◽  
Theoretical Predictions ◽  
The Stability ◽  
Stability Of Water ◽  
Spiral Grooves ◽  
Good Agreement

In this paper, the stability of water-lubricated, hydrostatic, conical bearings with spiral grooves for high-speed spindles is investigated theoretically and experimentally. In these bearing types, pressurized water is first fed to the inside of the rotating shaft and then introduced into spiral grooves through feeding holes located at one end of each spiral groove. Therefore, water pressure is increased due to the effect of the centrifugal force at the outlets of the feeding holes, which results from shaft rotation. In addition, water pressure is also increased by the viscous pumping effect of the spiral grooves. The stability of the proposed bearing is theoretically predicted using the perturbation method, and calculated results are compared with experimental results. It was consequently found that the proposed bearing is very stable at high speeds and theoretical predictions show good agreement with experimental data.

Comparison of Rotordynamic Analysis Predictions With the Test Response of Simple Gas Hybrid Bearings for Oil Free Turbomachinery

2003 ◽  
Author(s):  
Deborah A. Wilde ◽  
Luis San Andre´s
Keyword(s):  
High Speed ◽  
Natural Frequencies ◽  
Damping Ratio ◽  
Rotor Speed ◽  
Gas Bearings ◽  
Model Predictions ◽  
Rotor Bearing ◽  
Frequency Ratios ◽  
Bearing System ◽  
Good Agreement

Current applications of gas film bearings in high-speed oil-free micro-turbomachinery (<0.4 MW) require calibrated predictive tools to successfully deploy their application to mass-produced systems, for example oil-free turbochargers. The present investigation details the linear rotordynamic analysis of a test rotor supported on externally pressurized gas bearings. Model predictions are compared with the test rotordynamic response determined through comprehensive experiments conducted on a small rotor supported on three lobed hybrid (hydrostatic/hydrodynamic) rigid gas bearings. Predictions for the rotor-bearing system synchronous response to imbalance show good agreement with measurements during rotor coast downs, and manifest a decrease in damping ratio as the level of external pressurization increases. The rotor-bearing eigenvalue analysis forwards natural frequencies in accordance with the measurements, and null damping ratios evidence the threshold speeds of rotordynamic instability. Estimated whirl frequency ratios are typically 50% of rotor speed, thus predicting sub synchronous instabilities at lower rotor speeds than found experimentally when increasing the magnitude of feed pressurization. Rationale asserting the nature of the discrepancies calls for further analysis.

Pumping Characteristics of a Herringbone-Grooved Journal Bearing Functioning as a Viscous Vacuum Pump

1999 ◽  
Vol 122 (1) ◽  
pp. 131-136 ◽  
Author(s):  
S. Yoshimoto ◽  
Y. Ito ◽  
A. Takahashi
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Slip Flow ◽  
Laser Scanner ◽  
Vacuum Pump ◽  
Chamber Pressure ◽  
Design Parameters ◽  
Theoretical Predictions ◽  
Flow Effects ◽  
Good Agreement

A laser scanner motor with low power and high speed has been developed. This scanner motor uses a herringbone-grooved journal bearing which functions as a viscous vacuum pump. The windage power loss of a polygon mirror is reduced, since the air inside the pump housing is pumped out by herringbone-grooved viscous vacuum action. In this paper, the theoretical pumping characteristic of this bearing is investigated, using the narrow-groove theory and accounting for first-order slip flow. The effects of various design parameters on the pumping characteristics are discussed. Optimum geometric design parameters were found to obtain the minimum inner chamber pressure of the housing. The theoretical predictions considering slip flow effects are in good agreement with experimental measurements. [S0742-4787(00)01801-4]

Comparison of Rotordynamic Analysis Predictions With the Test Response of Simple Gas Hybrid Bearings for Oil Free Turbomachinery

2006 ◽  
Vol 128 (3) ◽  
pp. 634-643 ◽  
Author(s):  
Deborah A. Osborne ◽  
Luis San Andre´s
Keyword(s):  
High Speed ◽  
Natural Frequencies ◽  
Damping Ratio ◽  
Rotor Speed ◽  
Gas Bearings ◽  
Model Predictions ◽  
Rotor Bearing ◽  
Frequency Ratios ◽  
Bearing System ◽  
Good Agreement

Current applications of gas film bearings in high-speed oil-free microturbomachinery (<0.4 MW) require calibrated predictive tools to successfully deploy their application to mass-produced systems, for example, oil-free turbochargers. The present investigation details the linear rotordynamic analysis of a test rotor supported on externally pressurized gas bearings. Model predictions are compared with the test rotordynamic response determined through comprehensive experiments conducted on a small rotor supported on three lobed hybrid (hydrostatic/hydrodynamic) rigid gas bearings. Predictions for the rotor-bearing system synchronous response to imbalance show good agreement with measurements during rotor coastdowns, and manifest a decrease in damping ratio as the level of external pressurization increases. The rotor-bearing eigenvalue analysis forwards natural frequencies in accordance with the measurements, and null damping ratios evidence the threshold speeds of rotordynamic instability. Estimated whirl frequency ratios are typically 50% of rotor speed, thus predicting subsynchronous instabilities at lower rotor speeds than found experimentally when increasing the magnitude of feed pressurization. Rationale asserting the nature of the discrepancies calls for further analysis.

scholarly journals Displacement Transmissibility Characteristics of Harmonically Base Excited Damper Isolators with Mixed Viscous Damping

2013 ◽  
Vol 20 (5) ◽  
pp. 921-931 ◽  
Author(s):  
Xiaojuan Sun ◽  
Jianrun Zhang
Keyword(s):  
Damping Ratio ◽  
Harmonic Balance Method ◽  
Nonlinear Damping ◽  
Viscous Damping ◽  
Damping Force ◽  
Response Characteristics ◽  
Damping Characteristics ◽  
Linear Damping ◽  
Frequency Ratios ◽  
Good Agreement

The viscous damping force in the mixed form asfd(x˙)=c1x˙+c2|x˙|x˙can well describe damping characteristics of isolators and dampers in many cases. In this paper, performance characteristics of single-degree-of-freedom (SDOF) linear-stiffness isolators with mixed and piecewise mixed viscous damping are analytically examined under harmonic base excitation. Based on the first-order harmonic balance method (HBM), both relative and absolute displacement transmissibility expressions with the equivalent linear damping coefficient (ELDC) are given. And the analytical calculations show good agreement with the numerical results. Also, the influence of nonlinear damping on the response characteristics is investigated by comparing the transmissibility of linear and nonlinear systems. The resonant frequency always shifts to a lower value as the nonlinear damping component of the forcefd(x˙)=c1x˙+c2|x˙|x˙becomes stronger, and when the damping ratio in the corresponding linear model is relatively high, the relative transmissibility decreases at frequencies higher than the resonance frequency of the corresponding linear damping system and the absolute one increases for the frequency ratios above2. Finally, the displacement transmissibility of a nonlinear isolator with piecewise mixed viscous damping is discussed and the process shows research similarity with the non-piecewise case.

The Lubrication of Lightly Loaded Cylinders in Combined Rolling, Sliding, and Normal Motion—Part II: Experimental

1976 ◽  
Vol 98 (4) ◽  
pp. 517-522 ◽  
Author(s):  
P. H. Markho ◽  
D. Dowson
Keyword(s):  
Boundary Condition ◽  
Theoretical Analysis ◽  
High Speed ◽  
Squeeze Film ◽  
Theoretical Predictions ◽  
Good Agreement

This paper forms part of a wider investigation which includes the theoretical analysis given in Part I in addition to a study of the outlet cavitation boundary, using high-speed cine photography, reported elsewhere [4]. Pressure and some load measurements are presented which show good agreement with the theoretical predictions despite the well-known shortcomings of the Swift-Stieber boundary condition used in the analysis. Two sets of results have been included to cover the pure squeeze-film problem in addition to that of combined rolling, sliding and “normal” motion.

A crystallographic analysis of the CoSi/Si(111) interface using Transmission Electron Microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 574-575
Author(s):  
A.C. Daykin ◽  
C.J. Kiely ◽  
R.C. Pond ◽  
J.L. Batstone
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Defect Structure ◽  
Room Temperature ◽  
Theoretical Method ◽  
Crystallographic Analysis ◽  
Si Substrate ◽  
Transmission Electron ◽  
Theoretical Predictions

When CoSi2 is grown onto a Si(111) surface it can form in two distinct orientations. A-type CoSi2 has the same orientation as the Si substrate and B-type is rotated by 180° degrees about the [111] surface normal.One method of producing epitaxial CoSi2 is to deposit Co at room temperature and anneal to 650°C.If greater than 10Å of Co is deposited then both A and B-type CoSi2 form via a number of intermediate silicides .The literature suggests that the co-existence of A and B-type CoSi2 is in some way linked to these intermediate silicides analogous to the NiSi2/Si(111) system. The phase which forms prior to complete CoSi2 formation is CoSi. This paper is a crystallographic analysis of the CoSi2/Si(l11) bicrystal using a theoretical method developed by Pond. Transmission electron microscopy (TEM) has been used to verify the theoretical predictions and to characterise the defect structure at the interface.

Modeling of Tread Block Contact Mechanics Using Linear Viscoelastic Theory3

2008 ◽  
Vol 36 (3) ◽  
pp. 211-226 ◽  
Author(s):  
F. Liu ◽  
M. P. F. Sutcliffe ◽  
W. R. Graham
Keyword(s):  
High Speed ◽  
Slip Rate ◽  
Material Model ◽  
Contact Forces ◽  
Block Modeling ◽  
Rate Dependent ◽  
Linear Viscoelastic Material ◽  
Linear Viscoelastic ◽  
The Impact ◽  
Good Agreement

Abstract In an effort to understand the dynamic hub forces on road vehicles, an advanced free-rolling tire-model is being developed in which the tread blocks and tire belt are modeled separately. This paper presents the interim results for the tread block modeling. The finite element code ABAQUS/Explicit is used to predict the contact forces on the tread blocks based on a linear viscoelastic material model. Special attention is paid to investigating the forces on the tread blocks during the impact and release motions. A pressure and slip-rate-dependent frictional law is applied in the analysis. A simplified numerical model is also proposed where the tread blocks are discretized into linear viscoelastic spring elements. The results from both models are validated via experiments in a high-speed rolling test rig and found to be in good agreement.

Sign in / Sign up

Export Citation Format

Share Document