Raman analysis of the crystallinity degree for the local regions in Ge2Sb2Te5 films after laser exposure at different parameters

The evaluation of the crystallinity degree for the local regions in Ge2Sb2Te5 (GST) thin films after phase state transformation by laser pulses at 405 nm wavelength was analyzed using the Raman spectroscopy. The modes of laser radiation for controlling the reflectivity and transmissivity at 1550 nm telecommunication wavelength of the local regions in the GST film were established. The results obtained make it possible to implement the method of the completely optical control of the multilevel modulation of the optical signals for the integrated optics devices.

Preparation of Carbon Nanowall and Carbon Nanotube for Anode Material of Lithium-Ion Battery

Carbon nanowall (CNW) and carbon nanotube (CNT) were prepared as anode materials of lithium-ion batteries. To fabricate a lithium-ion battery, copper (Cu) foil was cleaned using an ultrasonic cleaner in a solvent such as trichloroethylene (TCE) and used as a substrate. CNW and CNT were synthesized on Cu foil using plasma-enhanced chemical vapor deposition (PECVD) and water dispersion, respectively. CNW and CNT were used as anode materials for the lithium-ion battery, while lithium hexafluorophosphate (LiPF6) was used as an electrolyte to fabricate another lithium-ion battery. For the structural analysis of CNW and CNT, field emission scanning electron microscope (FE-SEM) and Raman spectroscopy analysis were performed. The Raman analysis showed that the carbon nanotube in composite material can compensate for the defects of the carbon nanowall. Cyclic voltammetry (CV) was employed for the electrochemical properties of lithium-ion batteries, fabricated by CNW and CNT, respectively. The specific capacity of CNW and CNT were calculated as 62.4 mAh/g and 49.54 mAh/g. The composite material with CNW and CNT having a specific capacity measured at 64.94 mAh/g, delivered the optimal performance.

Preparation and Characterization of Biochar Derived from Agricultural By-Products for Dye Removal

In this study, biochar was derived from the agricultural by-products coconut coir (BC1) and rice husk (BC2) activated with NaOH 25%. This material was characterized through analytical methods such as SEM images, XRD, FTIR, and Raman. Analysis results indicated that the carbon structure carbon is amorphous and with many graphene layers. A high specific surface area was detected with 364.22 m2.g-1 for BC1 and 329.71 m2.g-1 for BC2 with many meso and micropores when analyzed by N2 and CO2 adsorption. The material also showed anionic and cationic dye adsorption capacity for textile wastewater following both Langmuir and Freundlich models where BC2 had better max adsorption capacity compared to BC1, 6.519 mg.g-1 for MO and 8.612 mg.g-1 for MB.

Structure and Dielectric Behavior of Yb2O3-MgO Co-Doped 0.92BaTiO3-0.08(Na0.5Bi0.5)TiO3 Ferroelectric Relaxor

Dielectric properties and structure of 0.015Yb2O3-xMgO doped 0.92BaTiO3-0.08(Na0.5Bi0.5)TiO3 ceramics with x = 0.0–0.025 have been investigated. As Yb2O3-MgO was added into the BT-NBT, the phase changes from tetragonal to pseudo-cubic, with the tetragonality c/a decreases from 1.011 to 1.008 and XRD peaks broadened. The combined study of XRD and TEM image revealed a formation of core–shell structure in grains with core of 400–600 nm and the shell of a thickness 60–200 nm. There is a slowly phase transition against temperature from the variable temperature Raman analysis. The ferroelectric relaxor peak of BT-NBT decreases from ~4000 to ~2000 and a new broad dielectric peak with an equivalent maximum (εr′~2300) appears in the temperature dependent dielectric constant curve (εr′-T), which produces a flat εr′-T curve. Sample 0.92BaTiO3-0.08(Na0.5Bi0.5)TiO3-0.015Yb2O3-0.005 MgO and 0.92BaTiO3-0.08(Na0.5Bi0.5)TiO3-0.015Yb2O3-0.01MgO give a εr′ variation within ±14% and ±10% in 20–165 °C. The core–shell microstructure should take account for the flattened εr′–T behavior of these samples.