effective coefficients
Recently Published Documents


TOTAL DOCUMENTS

125
(FIVE YEARS 29)

H-INDEX

19
(FIVE YEARS 4)

Author(s):  
Sanjeev Kumar Singh ◽  
Saroja Kanta Panda

In this paper, a micromechanics method is developed to evaluate effective coefficients of piezoelectric fiber-reinforced composites. An exact solution is derived for effective elastic, piezoelectric and dielectric coefficients of such piezocomposites subjected to the applied load in the direction transverse to the fiber orientation. Simultaneously, based on finite element method, a numerical study is performed on a representative volume element of such piezo composite containing fiber in square packing arrangement. The finite element method provides a numerical solution to evaluate effective elastic, piezoelectric and dielectric coefficients for discrete volume fraction of fiber, the range being 0.1–0.6 for this study. The results are interpolated to understand the overall behavior of such piezocomposites. The results obtained from the micromechanics method and the finite element method are compared with the results obtained from other models based on strength of materials method given in the literature. It is observed that the method developed in this study provides better results for effective coefficients susceptible to fiber packing arrangements.


2021 ◽  
Vol 2021 (10) ◽  
Author(s):  
Fang-Min Cai ◽  
Wei-Jun Deng ◽  
Xin-Qiang Li ◽  
Ya-Dong Yang

Abstract With updated experimental data and improved theoretical calculations, several significant deviations are being observed between the Standard Model predictions and the experimental measurements of the branching ratios of $$ {\overline{B}}_{(s)}^0\to {D}_{(s)}^{\left(\ast \right)+}{L}^{-} $$ B ¯ s 0 → D s ∗ + L − decays, where L is a light meson from the set {π, ρ, K(∗)}. Especially for the two channels $$ {\overline{B}}^0\to {D}^{+}{K}^{-} $$ B ¯ 0 → D + K − and $$ {\overline{B}}_s^0\to {D}_s^{+}{\pi}^{-} $$ B ¯ s 0 → D s + π − , both of which are free of the weak annihilation contribution, the deviations observed can even reach 4–5σ. Here we exploit possible new-physics effects in these class-I non-leptonic B-meson decays within the framework of QCD factorization. Firstly, we perform a model-independent analysis of the effects from twenty linearly independent four-quark operators that can contribute, either directly or through operator mixing, to the quark-level b →$$ c\overline{u}d(s) $$ c u ¯ d s transitions. It is found that, under the combined constraints from the current experimental data, the deviations observed could be well explained at the 1σ level by the new-physics four-quark operators with γμ(1 − γ5) ⨂ γμ(1 − γ5) structure, and also at the 2σ level by the operators with (1 + γ5) ⨂ (1 − γ5) and (1 + γ5) ⨂ (1 + γ5) structures. However, the new-physics four-quark operators with other Dirac structures fail to provide a consistent interpretation, even at the 2σ level. Then, as two specific examples of model-dependent considerations, we discuss the case where the new-physics four-quark operators are generated by either a colorless charged gauge boson or a colorless charged scalar, with their masses fixed both at the 1 TeV. Constraints on the effective coefficients describing the couplings of these mediators to the relevant quarks are obtained by fitting to the current experimental data.


2021 ◽  
Author(s):  
KOSTIANTYN VASYLEVSKYI ◽  
BORYS DRACH ◽  
IGOR TSUKROV

3D woven composites are well known for their high strength, dimensional stability, delamination, and impact resistance. They are often used in aerospace, energy, and automotive industries where material parts can experience harsh service conditions including substantial variations in temperature. This may lead to significant thermal deformations and thermally-induced stresses in the material. Additionally, 3D woven composites are often produced using resin transfer molding (RTM) technique which involves curing the epoxy resin at elevated temperatures leading to accumulation of the processing-induced residual stress. Thus, understanding of effective thermal behavior of 3D woven composites is essential for their successful design and service. In this paper, the effective thermal properties of 3D woven carbon-epoxy composite materials are estimated using mesoscale finite element models previously developed for evaluation of the manufacturing-induced residual stresses. We determine effective coefficients of thermal expansion (CTEs) of the composites in terms of the known thermal and mechanical properties of epoxy resin and carbon fibers. We investigate how temperature sensitivity of the thermal and mechanical properties of the epoxy influences the overall thermal properties of the composite. The simulations are performed for different composite reinforcement morphologies including ply-to-ply and orthogonal. It is shown that even linear dependence of epoxy’s stiffness and CTE on temperature results in a nonlinear dependence on temperature of the overall composite’s CTE.


2021 ◽  
Vol 8 (8) ◽  
pp. 210593
Author(s):  
Teik-Cheng Lim

A metamaterial that can manifest both positive and negative coefficients of moisture and thermal expansion is presented herein, based on inspiration from the Maltese cross. Each unit of the metamaterial consists of a pair of equal-armed crosses pin-joined at their junctions to permit rotation, but elastically restrained by a bimaterial spiral spring, and four pairs of hinge rods to translate the relative rotational motion of the pair of equal-armed crosses into translational motion of the connecting rods. The effective coefficients of moisture and thermal expansion models were developed for small and large changes in the hygrothermal conditions using infinitesimal (approximate) and finite (exact) motion analyses, respectively, with the former giving constant effective coefficients with respect to environmental changes. Results indicate that the approximate method underestimates the magnitude of both the effective expansion coefficients under cooling and drying but overestimates magnitudes of both coefficients during heating and moistening, and that the change in both expansion coefficients is more drastic during cooling and drying than during heating and moistening. In addition to providing another micro-lattice geometry for effecting expansion coefficients of either signs, this metamaterial exhibits auxetic property.


2021 ◽  
Vol 11 (12) ◽  
pp. 5354
Author(s):  
Rodolfo Avellaneda ◽  
Suset Rodríguez-Alemán ◽  
José A. Otero

Effective elastic and thermal properties for isotropic or transversely isotropic thermoelastic fibrous composite materials are obtained. Fibers are distributed with the same periodicity along the two perpendicular directions to the fiber orientation. The periodic cell of the composite has a square or hexagonal distribution. Perfect contact between the fiber and the matrix is presented. The effective properties are calculated using a semi-analytical method. The semi-analytical method consists of obtaining the differential equations that describe the local problems using the Asymptotic Homogenization Method. Then, these equations are solved using the Finite Element Method. Effective elastic coefficient (C¯), effective thermal expansion coefficient (α¯) and the effective thermal conductivity (κ¯) are obtained. The numerical results are compared with the semi-analytical solution and with results reported by other authors. Additionally, the effective properties for a fiber with an elliptical cross section are calculated. Distributions of the fiber’s cross section with different orientations are also studied. A MATLAB program for computing the effective coefficients is presented.


2021 ◽  
Vol 15 ◽  
pp. 61-68
Author(s):  
Beketayeva Meruyert

Knowledge of the laws of diffusion is necessary in the description, design and calculation of the mass transfer process in the production, operation and transportation of gaseous fuels. In this article, the calculation of diffusion processes for five natural hydrocarbon gas mixtures into the air was carried out. The effective diffusion coefficients and matrix coefficients of multicomponent diffusion were determined. Also the advantages of using effective coefficients in the description of mass transfer were shown.


2021 ◽  
Vol 2 (2) ◽  
pp. 125-141
Author(s):  
Luiz Roberto Evangelista ◽  
Giovanni Barbero ◽  
Anca Luiza Alexe-Ionescu

We discuss the foundations of a model based on an extension of the Langmuir approximation for the adsorption–desorption phenomena, in which the phenomenological coefficients depend on the bias potential, in addition to their dependence on the adsorption energy. The theoretical analysis focuses on the effect of these effective coefficients on the electrical response of an electrolytic cell to an external electric field, as predicted by the Poisson–Nernst–Planck model. Kinetic balance equations govern the current densities on the electrodes when the adsorption phenomenon occurs in the presence of an electric bias. The influence of the phenomenological parameters entering the model, as well as of the symmetry of the cell on the cyclic voltammetry, is investigated.


Sign in / Sign up

Export Citation Format

Share Document