A Procedure for the Fatigue Life Prediction of Straight Fibers Pneumatic Muscles

Different from the McKibben pneumatic muscle actuator, the straight fibers one is made of an elastomeric tube closed at the two ends by two heads that ensure a mechanical and pneumatic seal. High stiffness threads are placed longitudinally into the wall of the tube while external rings are placed at some sections of it to limit the radial expansion of the tube. The inner pressure in the tube causes shortening of the actuator. The working mode of the muscle actuator requires a series of critical repeated contractions and extensions that cause it to rupture. The fatigue life duration of a pneumatic muscle is often lower than traditional pneumatic actuators. The paper presents a procedure for the fatigue life prediction of a straight-fibers muscle based on experimental tests directly carried out with the muscles instead of with specimens of the silicone rubber material which the muscle is made of. The proposed procedure was experimentally validated. Although the procedure is based on fatigue life duration data for silicone rubber, it can be extended to all straight-fibers muscles once the fatigue life duration data of any material considered for the muscles is known.

Studies Regarding the Use of Pneumatic Muscles in Precise Positioning Systems

The paper presents the methods and results of an experimental study that highlights the behavior of a pneumatic actuator under different pressures and with different loads applied. One important challenge that occurs in the application of pneumatic muscles is the phenomenon of hysteresis, which causes a nonlinear relationship between the input–output values. The aim of this study is to identify the occurrence of hysteresis in the operation of a small pneumatic muscle in different conditions. Thus, different loads are attached to the free end of a pneumatic muscle and different successive pressures are applied in order to examine the hysteresis of the contraction ratio when the muscle is inflated and then deflated. The obtained equations that describe the relationship between the input pressure and the axial contraction are significant for reaching a high-performance position control. In this regard, the article proposes a solution to increase positioning accuracy based on pressure control using a proportional pressure regulator and a programmable logic controller.

Research on frog-inspired swimming robot driven by pneumatic muscles

This article designs a frog-inspired swimming robot based on pneumatic muscles. The musculoskeletal characteristics of the frog are refined and used as the basis for the design of the robot joint structure and movement mode. The posture adjustment module, joint water seal, and power system are designed to meet the robot’s motion requirements, and the structure optimization design of the robot is completed by combining simulation analysis. The body length of the robot is about 710 mm, and the overall mass is 10 kg. Combining the structural characteristics of the robot, the control system is built to realize the frog-like motion. The robot’s propulsion speed is about 0.6 m/s, the propulsion distance reaches 2.4 m, the turning angle is 30°, and the turning radius is 0.6 m. The prototype experiment verifies the rationality of the frog-inspired swimming robot structure design and the reliability of the control system and water seal.

Design, Fabrication, and Performance Analysis of a Vertically Suspended Soft Manipulator

Soft continuum manipulators are comprised of flexible materials in a serpentine shape. Such manipulators can be controlled mechanically through tendons or pneumatic muscles. Continuum manipulators utilizing tendons are traditionally formed in a thick cross section, which presents limitations in achieving a high bending range as well as difficulties for storage and transportation. This study introduces a continuum manipulator comprised of two thin plastic bands and driven by a tendon to provide a bending action. The manipulator’s thin body form enables it to be rolled up for storage and transportation. Experimental results on different section lengths show the possibility of achieving a horizontal displacement of up to 34% of the bending-segment’s length, and a full closed-loop curvature for most segments. However, the results also indicated an elongation of the tip paths owing to gravity. These results, in addition to the manipulator’s flexibility and light weight features, confirm its suitability for applications in space and underwater environments.

Determination of the Function of the Course of the Static Property of PAMs as Actuators in Industrial Robotics

Current efforts are focused on assembling new constructions while applying non-conventional actuators, for example, artificial pneumatic muscles, in engineering manufacturing processes. The reason is to eliminate stiffness and inflexibility of equipment structures that make sharing the working space of the technological equipment complicated. This article presents the results of experimental measurements of pressures in artificial muscles and rotations of the actuator with artificial muscles at various loads, using a testing device of an antagonistic actuator. The measurement results were used to create the function of the course of the static property of the antagonistic actuator with artificial muscles of the Festo type and to determine a mathematical model of the actuator dynamics, while applying the method of least squares.

Overview of solutions used in rehabilitation devices using muscles and pneumatic actuators

The article presents selected rehabilitation devices with the use of classic actuators and pneumatic muscles. Manipulators supporting the movements of the lower and upper limbs of humans are presented. Moreover, the construction of actuators and pneumatic muscles is described.