Influence of Sweat on Joint and Sensor Reliability of E-Textiles

This article addresses reliability under the sweat of interconnection techniques for the mounting surface mounted device (SMD) components and fully printed humidity sensors onto conductive stretchable textile ribbons. Samples underwent testing for the effect of ageing by artificial sweat on their electrical resistance using both alkaline and acidic artificial sweat. The best results in terms of electrical resistance change were obtained for samples soldered to the conductive fibers interwoven in the ribbon. However, this method can damage the ribbon due to the high temperature during soldering and significantly reduce the mechanical properties and flexibility of the ribbon, which can lead to a limited service life of samples. On the other hand, adhesive bonding is a very interesting alternative, where the above-mentioned properties are preserved, but there is a significant effect of sweat ageing on electrical resistance. The results of fully printed graphene-based humidity sensors show that, for the intended use of these sensors (i.e., detection of changes in moisture on the human body), usage of the samples is possible, and the samples are sufficiently reliable in the case of sweat degradation. In addition, the response of the sensor to humidity is quite high: 98% at a relative humidity of 98%.

Effects of Artificial Sweat Formulation and Extraction Temperature on Estimation of the Dermal Bioaccessibility of Potentially Toxic Elements in a Contaminated Soil from an E-Waste Recycling Site

Informal recycling of electronic waste leads to soil contamination that can impact human health. To accurately assess exposure to potentially toxic elements (PTE) in soil it is necessary to consider their bioavailability through ingestion, inhalation and dermal contact. However, bioaccessibility tests that estimate dermal absorption following adhesion of contaminated soil particles to skin are not well established. In this study the concentrations of As, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn were estimated in the <45 µm particle size fraction of a bulk composite soil from an e-waste recycling site using five different artificial sweat formulations. Extractions were performed at temperatures ranging from 17 to 47 °C to investigate the effect of ambient temperature on bioaccessibility. Results obtained using the different artificial sweats were not consistent with one another. In particular, the NIHS 96-10 formulation solubilized larger amounts of analytes (ranging from 6.3 times the next most effective extractant for Cu to 1700 times the next most effective for Pb). There was a general increase in release of PTE with increasing temperature, except for As. Although trends varied between analytes and formulations, this highlights the need to consider ambient temperature when estimating dermal bioaccessibility of PTE in soil.

Antioxidant Power on Dermal Cells by Textiles Dyed with an Onion (Allium cepa L.) Skin Extract

In this study, the phenol loading and antioxidant activity of wool yarn prepared with the aqueous extract of onion (Allium cepa L.) skin was enhanced by implementing the dyeing process with the use of alum as a mordant. Spectrophotometric and chromatographic methods were applied for the characterization of polyphenolic substances loaded on the wool yarn. The antioxidant/anti-inflammatory properties were evaluated by determining the level of intra- and extra-cellular reactive oxygen species (ROS) production in keratinocytes and dermal fibroblasts pre-treated with lipopolysaccharide put in contact with artificial sweat. An elevated dye uptake on wool was observed for the pre-mordanted sample, as demonstrated by high absorbance values in the UV-Visible spectral range. Chromatographic results showed that protocatechuic acid and its glucoside were the main phenolic acid released in artificial sweat by the wool yarns, while quercetin-4′-glucoside and its aglycone quercetin were more retained. The extract released from the textile immersed in artificial sweat showed a significant reducing effect on the intra-and extracellular ROS levels in the two cell lines considered. Cytofluorimetric analyses demonstrated that the selected mordant was safe at the concentration used in the dyeing procedure. Therefore, alum pre-mordanted textiles dyed with onion-skin extracts may represent an interesting tool against skin diseases.

Alginate Bead Biosystem for the Determination of Lactate in Sweat Using Image Analysis

Lactate is present in sweat at high concentrations, being a metabolite of high interest in sport science and medicine. Therefore, the potential to determine lactate concentrations in physiological fluids, at the point of need with minimal invasiveness, is very valuable. In this work, the synthesis and performance of an alginate bead biosystem was investigated. Artificial sweat with different lactate concentrations was used as a proof of concept. The lactate detection was based on a colorimetric assay and an image analysis method using lactate oxidase, horseradish peroxidase and tetramethyl benzidine as the reaction mix. Lactate in artificial sweat was detected with a R² = 0.9907 in a linear range from 10 mM to 100 mM, with a limit of detection of 6.4 mM and a limit of quantification of 21.2 mM. Real sweat samples were used as a proof of concept to test the performance of the biosystem, obtaining a lactate concentration of 48 ± 3 mM. This novel sensing configuration, using alginate beads, gives a fast and reliable method for lactate sensing, which could be integrated into more complex analytical systems.

Controllable Release of Povidone-Iodine from Networked Pectin@Carboxymethyl Pullulan Hydrogel

Povidone-iodine (PI) is a common antiseptic reagent which is used for skin infections and wound healing. The control release of PI is quite important to heal the deep and intense wounds. Herein, the preparation of biodegradable pectin@carboxymethyl pullulan (Pe@CMP) hydrogel was carried out and applied for controllable release of PI. CMP was synthesized by interaction of monochloroacetic acid with pullulan at different ratios. The Pe@CMP hydrogel was then prepared by crosslinking of pectin with CMP in presence of glutaraldehyde as cross linker. After carboxymethylation, COOH contents were enlarged to be 24.2–51.2 mmol/kg and degree of substitution was 0.44–0.93. The rheological properties of Pe@CMP hydrogel were enlarged by increment of pectin ratio. Swelling ratio in water (16.0–18.0%) was higher than that of artificial sweat (11.7–13.2%). Pe@CMP hydrogel containing 20% pectin, exhibited the lowest release and 57.7% from PI was released within 360 min. The biological activity of the released PI was monitored to be highly efficient. The kinetic of release was fitted well to the first ordered reaction and Higuchi models. The mechanism of release was explained by the swelling of hydrogel. The networked structure of hydrogel was opened by swelling and PI was released from the outer pores followed by inner pores, achieving the controllable release.

Safety Assessment of Polypyrrole Nanoparticles and Spray-Coated Textiles

Polypyrrole (PPy) nanoparticles (NPs) are used for the coating of materials, such as textiles, with biomedical applications, including wound care and tissue engineering, but they are also promising antibacterial agents. In this work, PPy NPs were used for the spray-coating of textiles with antimicrobial properties. The functional properties of the materials were verified, and their safety was evaluated. Two main exposure scenarios for humans were identified: inhalation of PPy NPs during spray (manufacturing) and direct skin contact with NPs-coated fabrics (use). Thus, the toxicity properties of PPy NPs and PPy-coated textiles were assessed by using in vitro models representative of the lung and the skin. The results from the materials’ characterization showed the stability of both the PPy NP suspension and the textile coating, even after washing cycles and extraction in artificial sweat. Data from an in vitro model of the air–blood barrier showed the low toxicity of these NPs, with no alteration of cell viability and functionality observed. The skin toxicity of PPy NPs and the coated textiles was assessed on a reconstructed human epidermis model following OECD 431 and 439 guidelines. PPy NPs proved to be non-corrosive at the tested conditions, as well as non-irritant after extraction in artificial sweat at two different pH conditions. The obtained data suggest that PPy NPs are safe NMs in applications for textile coating.