Effect of nano silica and fine silica sand on compressive strength of sodium and potassium activators synthesised fly ash geopolymer at elevated temperatures

2017 ◽  
Vol 42 (3) ◽  
pp. 324-335 ◽  
Author(s):  
Faiz Shaikh ◽  
Sharany Haque
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Elevated Temperatures ◽  
Silica Sand ◽  
Nano Silica ◽  
Sodium And Potassium

scholarly journals Late Age Dynamic Strength of High-Volume Fly Ash Concrete with Nano-Silica and Polypropylene Fibres

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 243 ◽  
Author(s):  
Mohamed H. Mussa ◽  
Ahmed M. Abdulhadi ◽  
Imad Shakir Abbood ◽  
Azrul A. Mutalib ◽  
Zaher Mundher Yaseen
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Elevated Temperatures ◽  
High Volume ◽  
Nano Silica ◽  
Polypropylene Fibres ◽  
Fly Ash Concrete ◽  
High Volume Fly Ash ◽  
Dynamic Compressive Strength ◽  
Curing Age

The dynamic behaviour of high-volume fly ash concrete with nano-silica (HVFANS) and polypropylene fibres at curing ages of 7 to 90 days was determined by using a split Hopkinson pressure bar (SHPB) machine. At each curing age, the concrete samples were laboratory tested at different temperatures conditions under strain rates reached up to 101.42 s−1. At room temperature, the results indicated that the dynamic compressive strength of plain concrete (PC) was slightly higher than HVFANS concrete at early curing ages of 7 and 28 days, however, a considerable improvement in the strength of HVFANS concrete was noted at a curing age of 90 days and recorded greater values than PC owing to the increase of fly ash reactivity. At elevated temperatures, the HVFANS concrete revealed a superior behaviour than PC even at early ages in terms of dynamic compressive strength, critical strain, damage and toughness due to increase of nano-silica (NS) activity during the heating process. Furthermore, equations were suggested to estimate the dynamic increase factor (DIF) of both concretes under the investigated factors.

Effects of Elevated Temperatures on the Compressive Strength of HFCC

2011 ◽  
Vol 261-263 ◽  
pp. 416-420 ◽  
Author(s):  
Fu Ping Jia ◽  
Heng Lin Lv ◽  
Yi Bing Sun ◽  
Bu Yu Cao ◽  
Shi Ning Ding
Keyword(s):  
Compressive Strength ◽  
Elevated Temperature ◽  
Fly Ash ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Relative Strength ◽  
Ordinary Concrete ◽  
Residual Compressive Strength ◽  
Fly Ash Concrete ◽  
The Relationship

This paper presents the results of elevated temperatures on the compressive of high fly ash content concrete (HFCC). The specimens were prepared with three different replacements of cement by fly ash 30%, 40% and 50% by mass and the residual compressive strength was tested after exposure to elevated temperature 250, 450, 550 and 650°C and room temperature respectively. The results showed that the compressive strength apparently decreased with the elevated temperature increased. The presence of fly ash was effective for improvement of the relative strength, which was the ratio of residual compressive strength after exposure to elevated temperature and ordinary concrete. The relative compressive strength of fly ash concrete was higher than those of ordinary concrete. Based on the experiments results, the alternating simulation formula to determine the relationship among relative strength, elevated temperature and fly ash replacement is developed by using regression of results, which provides the theoretical basis for the evaluation and repair of HFCC after elevated temperature.

scholarly journals Research on Mechanical Performance & Behaviour of Geopolymer Concrete Subjected to Elevated Temperatures

2019 ◽  
Vol 8 (2S8) ◽  
pp. 883-887
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Geopolymer Concrete ◽  
Sem Images ◽  
Before And After ◽  
Alkaline Conditions ◽  
Compressive Strength Of Concrete

The investigative studies on mechanical performance & behaviour, of Geopolymer Concrete (GPC) before and after the exposure to elevated temperatures (of 200 0 C -1000 0 C with an increment of 100 0 C). Indicate that the GPC Specimens Exhibited better Compressive strength at higher temperatures than that of those made by regular OPC Concrete with M30 Grade. The chronological changes in the geopolymeric structure upon exposure to these temperatures and their reflections on the thermal behaviour have also been explored. The SEM images indicate GPC produced by fly ash , metakaolin and silica fume, under alkaline conditions form Mineral binders that are not only non-flammable and but are also non-combustible resins and binders. Further the Observations drawn disclose that the mass and compressive strength of concrete gets reduced with increase in temperatures.

High Volume Slag and Slag-Fly Ash Blended Cement Pastes Containing Nano Silica

2019 ◽  
Vol 967 ◽  
pp. 205-213
Author(s):  
Faiz U.A. Shaikh ◽  
Anwar Hosan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Paste ◽  
Ordinary Portland Cement ◽  
Blended Cement ◽  
High Volume ◽  
Ash Content ◽  
Partial Replacement ◽  
Nano Silica ◽  
Cement Pastes

This paper presents the effect of nanosilica (NS) on compressive strength and microstructure of cement paste containing high volume slag and high volume slag-fly ash blend as partial replacement of ordinary Portland cement (OPC). Results show that high volume slag (HVS) cement paste containing 60% slag exhibited about 4% higher compressive strength than control cement paste, while the HVS cement paste containing 70% slag maintained the similar compressive strength to control cement paste. However, about 9% and 37% reduction in compressive strength in HVS cement pastes is observed due to use of 80% and 90% slag, respectively. The high volume slag-fly ash (HVSFA) cement pastes containing total slag and fly ash content of 60% exhibited about 5%-16% higher compressive strength than control cement paste. However, significant reduction in compressive strength is observed in higher slag-fly ash blends with increasing in fly ash contents. Results also show that the addition of 1-4% NS improves the compressive strength of HVS cement paste containing 70% slag by about 9-24%. However, at higher slag contents of 80% and 90% this improvement is even higher e.g. 11-29% and 17-41%, respectively. The NS addition also improves the compressive strength by about 1-59% and 5-21% in high volume slag-fly ash cement pastes containing 21% fly ash+49%slag and 24% fly ash+56%slag, respectively. The thermogravimetric analysis (TGA) results confirm the reduction of calcium hydroxide (CH) in HVS/HVSFA pastes containing NS indicating the formation of additional calcium silicate hydrate (CSH) gels in the system. By combining slag, fly ash and NS in high volumes e.g. 70-80%, the carbon footprint of cement paste is reduced by 66-76% while maintains the similar compressive strength of control cement paste. Keywords: high volume slag, nanosilica, compressive strength, TGA, high volume slag-fly ash blend, CO2 emission.

EFFECT OF MIXING PROPORTION ON COMPRESSIVE STRENGTH OF FLY-ASH BASED GEOPOLYMER PASTE AND MORTAR USING TAGUCHI’S METHOD

2015 ◽  
Vol 2 (1) ◽  
Author(s):  
Sajid Khan Afridi ◽  
Vanissorn Vimonsatit
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Elevated Temperatures ◽  
Three Dimensional ◽  
Silica Content ◽  
Polymeric Chain ◽  
Low Carbon ◽  
Solid Ratio ◽  
Mix Proportion ◽  
Alkali Activated

Alkali activated pozzolan are known low carbon cementitious binders which can be used to replace cement. The material is also known as geopolymer because of its three dimensional polymeric chain and ring like structure consisting silica and alumina. A common type of pozzolan used is fly ash because of its rich silica content; therefore the term alkali activated fly-ash based binders is adopted. Despite much research and development of this material, there is no specific standard for design mix proportion. This research used the Taguchi’s design of experiment method to determine the optimum mix proportion of alkali activated fly ash based cement paste and mortar. Four factors were considered in the tests, silica fume, sand to cementitious ratio, liquid to solid ratio, and percentage of superplasticiser. Tests were conducted on the 9 batches of alkali activated fly-ash based paste and mortar samples to determine the compressive strength under ambient condition. Tests were also conducted to determine the residual strength of the samples after exposed to elevated temperatures. ANOVA analysis of the test results revealed the main factors contribution on the tested properties and led to the determination of the optimum design proportion of the factors considered in these tests.

scholarly journals Effect of Elevated Temperatures on Mortar with Naturally Occurring Volcanic Ash and Its Blend with Electric Arc Furnace Slag

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Nauman Khurram ◽  
Kaffayatullah Khan ◽  
Muhammad Umair Saleem ◽  
Muhammad Nasir Amin ◽  
Usman Akmal
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Volcanic Ash ◽  
Elevated Temperatures ◽  
Electric Arc Furnace ◽  
Electric Arc ◽  
Arc Furnace ◽  
Test Results ◽  
Electric Arc Furnace Slag ◽  
Furnace Slag

The mechanical behavior of basaltic volcanic ash (VA) and fly ash (FA) as a cement replacement under elevated temperatures is mainly investigated in the current study. For this, cement content has been partially replaced with and without the presence of electric arc furnace slag (S). Four distinct ranges of temperatures (200°C, 400°C, 600°C, and 800°C) were selected, and the modified mixes were subjected to these gradually elevated temperatures. Samples were cured and cooled by using air- and water-cooling techniques. Test results were established by examining the sample weights and compressive strength before and after the exposure of each temperature level. The pozzolanic potential of volcanic ash and fly ash samples was identified using the strength activity index. After analyzing the test results, it has been found that there is a significant effect on the compressive strength of mortar mixes at the early ages of its strength gain. However, at the later ages of curing, samples modified with volcanic and fly ash with the presence of electric arc furnace slag have shown a better performance than control mix in terms of strength and weight loss.

scholarly journals Mechanical and Microstructural Characterization of Quarry Rock Dust Incorporated Steel Fiber Reinforced Geopolymer Concrete and Residual Properties after Exposure to Elevated Temperatures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6890
Author(s):  
Muhammad Ibraheem ◽  
Faheem Butt ◽  
Rana Muhammad Waqas ◽  
Khadim Hussain ◽  
Rana Faisal Tufail ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Strength ◽  
Elevated Temperatures ◽  
Strength Properties ◽  
Steel Fibers ◽  
Geopolymer Concrete

The purpose of this research is to study the effects of quarry rock dust (QRD) and steel fibers (SF) inclusion on the fresh, mechanical, and microstructural properties of fly ash (FA) and ground granulated blast furnace slag (SG)-based geopolymer concrete (GPC) exposed to elevated temperatures. Such types of ternary mixes were prepared by blending waste materials from different industries, including QRD, SG, and FA, with alkaline activator solutions. The multiphysical models show that the inclusion of steel fibers and binders can enhance the mechanical properties of GPC. In this study, a total of 18 different mix proportions were designed with different proportions of QRD (0%, 5%, 10%, 15%, and 20%) and steel fibers (0.75% and 1.5%). The slag was replaced by different proportions of QRD in fly ash, and SG-based GPC mixes to study the effect of QRD incorporation. The mechanical properties of specimens, i.e., compressive strength, splitting tensile strength, and flexural strength, were determined by testing cubes, cylinders, and prisms, respectively, at different ages (7, 28, and 56 days). The specimens were also heated up to 800 °C to evaluate the resistance of specimens to elevated temperature in terms of residual compressive strength and weight loss. The test results showed that the mechanical strength of GPC mixes (without steel fibers) increased by 6–11%, with an increase in QRD content up to 15% at the age of 28 days. In contrast, more than 15% of QRD contents resulted in decreasing the mechanical strength properties. Incorporating steel fibers in a fraction of 0.75% by volume increased the compressive, tensile, and flexural strength of GPC mixes by 15%, 23%, and 34%, respectively. However, further addition of steel fibers at 1.5% by volume lowered the mechanical strength properties. The optimal mixture of QRD incorporated FA-SG-based GPC (QFS-GPC) was observed with 15% QRD and 0.75% steel fibers contents considering the performance in workability and mechanical properties. The results also showed that under elevated temperatures up to 800 °C, the weight loss of QFS-GPC specimens persistently increased with a consistent decrease in the residual compressive strength for increasing QRD content and temperature. Furthermore, the microstructure characterization of QRD blended GPC mixes were also carried out by performing scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive spectroscopy (EDS).

Sign in / Sign up

Export Citation Format

Share Document