Fluctuation at High Temperature Combined with Nutrients Alters the Thermal Dependence of Phytoplankton

2021 ◽  
Author(s):  
Juan Manuel González-Olalla ◽  
Juan Manuel Medina-Sánchez ◽  
Presentación Carrillo
Keyword(s):  
High Temperature ◽  
Thermal Dependence

scholarly journals Thermographic properties of Eu3+ and Sm3+ doped Lu2O3 nanophosphor

2012 ◽  
Vol 77 (12) ◽  
pp. 1735-1746 ◽  
Author(s):  
Vesna Lojpur ◽  
Zeljka Antic ◽  
Radenka Krsmanovic ◽  
Mina Medic ◽  
Marko Nikolic ◽  
...  
Keyword(s):  
High Temperature ◽  
Morphological Properties ◽  
Polymer Complex ◽  
Nucleation Agent ◽  
Thermal Dependence ◽  
Knowing That ◽  
Lutetium Oxide ◽  
Transmission Electron ◽  
Thermographic Phosphors ◽  
Phosphor Thermometry

The samples, Lu2O3:Eu3+ (3at.% Eu) and Lu2O3:Sm3+ (1at.% Sm), were prepared via polymer complex solution method using polyethlylene-glyocol as the fuel and as nucleation agent for crystallization process. Knowing that lutetium oxide has high chemical stability and temperature resistance, in this paper we investigated possibility for its application in high-temperature phosphor thermometry. It is a non-contact technique that uses the thermal dependence of phosphor fluorescence to measure temperature remotely. The structural and morphological properties were performed through X-ray powder diffraction (XRPD) and transmission electron microscopy (TEM) investigations. The obtained results confirmed that this synthesis yields desired crystalline structure with particle size in the range from 30 to 50 nm. Photoluminescence emission measurements were recorded in the temperature range from room up to 873 K. The accomplished results demonstrate the performance of Eu3+ and Sm3+ doped Lu2O3 as high temperature thermographic phosphors of very good sensitivity.

A high-temperature Fourier transform infrared study of the interlayer and Si–O-stretching region in phengite-2M1

Clay Minerals ◽  
2002 ◽  
Vol 37 (2) ◽  
pp. 323-336 ◽  
Author(s):  
M. Mookherjee ◽  
S. A. T. Redfern
Keyword(s):  
High Temperature ◽  
Bond Length ◽  
Structural Changes ◽  
Far Infrared ◽  
Infrared Region ◽  
Thermal Dependence ◽  
Infrared Study ◽  
Mid Infrared ◽  
Infrared Measurements ◽  
Bond Strain

AbstractA natural phengite-2M1 of composition (K0.95Na0.05)(Al0.76Fe0.14Mg0.10)2 (Si3.25Al0.75)O10(OH1.96F0.04) [a= 5.2173(1) Å, b= 9.0493(2) Å, c= 19.989 (1) Å and β = 95.734(4)°] was studied using in situ high-temperature FTIR. Correlations to structural changes were made using previously-reported neutron diffraction data from the same sample. Correlations have been made between the microscopic atomic displacements (arising from thermal effects) and analogous macroscopic properties, such as bond strain and ditrigonal distortions. Spectra were collected in the far-infrared region to study the behaviour of the interlayer (K+) cation and also in the mid-infrared region to distinguish the Si–O stretching modes. We found anisotropic thermal expansion of the interlayer site. The K O bond length is divided into K Oouter and K Oinner, and the K–Oinner bond length is correlated with the far-infrared spectra. The thermal dependence of the correlation between K–O bond length and corresponding far-infrared stretching frequency is different from the effect of the chemical composition. We also found that the K–O bond strain could be successfully resolved into the sum of inner strain and lattice strain. The Si–O stretching mode, obtained from the mid-infrared measurements, showed only weak changes. However, the neutron refinement data showed different thermal behaviour for distinct crystallographic T-sites.

Influence of Thermo-Mechanical Processing on the Microstructure of Beryllia Dispersed Nickel Alloys

1973 ◽  
Vol 31 ◽  
pp. 184-185
Author(s):  
M.S. Grewal ◽  
S.A. Sastri ◽  
N.J. Grant
Keyword(s):  
High Temperature ◽  
Nickel Alloys ◽  
Thermomechanical Processing ◽  
Cold Work ◽  
High Temperature Strength ◽  
Strengthening Effect ◽  
Mechanical Processing ◽  
Uniform Dispersion ◽  
Oxide Particles ◽  
Nickel Base

Currently there is a great interest in developing nickel base alloys with fine and uniform dispersion of stable oxide particles, for high temperature applications. It is well known that the high temperature strength and stability of an oxide dispersed alloy can be greatly improved by appropriate thermomechanical processing, but the mechanism of this strengthening effect is not well understood. This investigation was undertaken to study the dislocation substructures formed in beryllia dispersed nickel alloys as a function of cold work both with and without intermediate anneals. Two alloys, one Ni-lv/oBeo and other Ni-4.5Mo-30Co-2v/oBeo were investigated. The influence of the substructures produced by Thermo-Mechanical Processing (TMP) on the high temperature creep properties of these alloys was also evaluated.

Application of TEM to Deformation, Wear, and Fracture of Ceramics

1974 ◽  
Vol 32 ◽  
pp. 472-473
Author(s):  
B. J. Hockey
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Mechanical Behavior ◽  
Brittle Materials ◽  
High Temperature Strength ◽  
Wide Range ◽  
Corrosive Environments ◽  
Further Development

Ceramics, such as Al2O3 and SiC have numerous current and potential uses in applications where high temperature strength, hardness, and wear resistance are required often in corrosive environments. These materials are, however, highly anisotropic and brittle, so that their mechanical behavior is often unpredictable. The further development of these materials will require a better understanding of the basic mechanisms controlling deformation, wear, and fracture.The purpose of this talk is to describe applications of TEM to the study of the deformation, wear, and fracture of Al2O3. Similar studies are currently being conducted on SiC and the techniques involved should be applicable to a wide range of hard, brittle materials.

Lattice Imaging of Grain Boundaries in Ceramics

1977 ◽  
Vol 35 ◽  
pp. 114-115
Author(s):  
D. R. Clarke ◽  
G. Thomas
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Grain Boundaries ◽  
High Temperature Strength ◽  
Current Interest ◽  
Lattice Imaging ◽  
Special Significance ◽  
Structural Applications ◽  
Refractory Ceramics

Grain boundaries have long held a special significance to ceramicists. In part, this has been because it has been impossible until now to actually observe the boundaries themselves. Just as important, however, is the fact that the grain boundaries and their environs have a determing influence on both the mechanisms by which powder compaction occurs during fabrication, and on the overall mechanical properties of the material. One area where the grain boundary plays a particularly important role is in the high temperature strength of hot-pressed ceramics. This is a subject of current interest as extensive efforts are being made to develop ceramics, such as silicon nitride alloys, for high temperature structural applications. In this presentation we describe how the techniques of lattice fringe imaging have made it possible to study the grain boundaries in a number of refractory ceramics, and illustrate some of the findings.

Effect of Improved ThO2 Particle Dispersion in Nickel on High-Temperature Strength

1970 ◽  
Vol 28 ◽  
pp. 444-445
Author(s):  
E. R. Kimmel ◽  
H. L. Anthony ◽  
W. Scheithauer
Keyword(s):  
High Temperature ◽  
Metal Matrix ◽  
Oxide Particle ◽  
Oxide Phase ◽  
Dislocation Motion ◽  
Particle Dispersion ◽  
High Temperature Strength ◽  
Strengthening Effect ◽  
Oxide Particles ◽  
The Stability

The strengthening effect at high temperature produced by a dispersed oxide phase in a metal matrix is seemingly dependent on at least two major contributors: oxide particle size and spatial distribution, and stability of the worked microstructure. These two are strongly interrelated. The stability of the microstructure is produced by polygonization of the worked structure forming low angle cell boundaries which become anchored by the dispersed oxide particles. The effect of the particles on strength is therefore twofold, in that they stabilize the worked microstructure and also hinder dislocation motion during loading.

The Ordered Phase Formation in Ti-Al-Ga Alloys

1970 ◽  
Vol 28 ◽  
pp. 440-441
Author(s):  
Shiro Fujishiro ◽  
Harold L. Gegel
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Titanium Alloys ◽  
Growth Kinetics ◽  
Stoichiometric Composition ◽  
Good Potential ◽  
Alpha Titanium ◽  
Cold Rolled ◽  
Kinetics Of ◽  
Thermal Stability Of

Ordered-alpha titanium alloys having a DO19 type structure have good potential for high temperature (600°C) applications, due to the thermal stability of the ordered phase and the inherent resistance to recrystallization of these alloys. Five different Ti-Al-Ga alloys consisting of equal atomic percents of aluminum and gallium solute additions up to the stoichiometric composition, Ti3(Al, Ga), were used to study the growth kinetics of the ordered phase and the nature of its interface.The alloys were homogenized in the beta region in a vacuum of about 5×10-7 torr, furnace cooled; reheated in air to 50°C below the alpha transus for hot working. The alloys were subsequently acid cleaned, annealed in vacuo, and cold rolled to about. 050 inch prior to additional homogenization

Albumins as Embedding Media for Electron Microscopy

1969 ◽  
Vol 27 ◽  
pp. 422-423 ◽  
Author(s):  
J. L. Farrant ◽  
J. D. McLean
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
High Temperature ◽  
Biological Material ◽  
Globular Proteins ◽  
The Past ◽  
Antibody Staining ◽  
Thin Sectioning ◽  
Embedding Medium

For electron microscope techniques such as ferritin-labeled antibody staining it would be advantageous to have available a simple means of thin sectioning biological material without subjecting it to lipid solvents, impregnation with plastic monomers and their subsequent polymerization. With this aim in view we have re-examined the use of protein as an embedding medium. Gelatin which has been used in the past is not very satisfactory both because of its fibrous nature and the high temperature necessary to keep its solutions fluid. We have found that globular proteins such as the serum and egg albumins can be cross-linked so as to yield blocks which are suitable for ultrathin sectioning.

An Environmental Wet Cell For High Voltage Electron Microscopy

1973 ◽  
Vol 31 ◽  
pp. 18-19
Author(s):  
N.J. Tighe ◽  
H.M. Flower ◽  
P.R. Swann
Keyword(s):  
Electron Microscopy ◽  
High Temperature ◽  
Image Quality ◽  
Inelastic Scattering ◽  
High Voltage ◽  
High Voltage Electron Microscopy ◽  
Voltage Electron ◽  
Environmental Cell ◽  
Water Saturated ◽  
High Temperature Gas

A differentially pumped environmental cell has been developed for use in the AEI EM7 million volt microscope. In the initial version the column of gas traversed by the beam was 5.5mm. This permited inclusion of a tilting hot stage in the cell for investigating high temperature gas-specimen reactions. In order to examine specimens in the wet state it was found that a pressure of approximately 400 torr of water saturated helium was needed around the specimen to prevent dehydration. Inelastic scattering by the water resulted in a sharp loss of image quality. Therefore a modified cell with an ‘airgap’ of only 1.5mm has been constructed. The shorter electron path through the gas permits examination of specimens at the necessary pressure of moist helium; the specimen can still be tilted about the side entry rod axis by ±7°C to obtain stereopairs.

Exsolution and inversion in pigeonite from the Whin Sill, Northern England

1978 ◽  
Vol 36 (1) ◽  
pp. 474-475
Author(s):  
P.P.K. Smith
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Homogeneous Nucleation ◽  
Silicate Mineral ◽  
Antiphase Boundaries ◽  
Two Phase ◽  
Primitive Form ◽  
The Core ◽  
Nucleation Mechanisms ◽  
And Inversion

Grains of pigeonite, a calcium-poor silicate mineral of the pyroxene group, from the Whin Sill dolerite have been ion-thinned and examined by TEM. The pigeonite is strongly zoned chemically from the composition Wo8En64FS28 in the core to Wo13En34FS53 at the rim. Two phase transformations have occurred during the cooling of this pigeonite:- exsolution of augite, a more calcic pyroxene, and inversion of the pigeonite from the high- temperature C face-centred form to the low-temperature primitive form, with the formation of antiphase boundaries (APB's). Different sequences of these exsolution and inversion reactions, together with different nucleation mechanisms of the augite, have created three distinct microstructures depending on the position in the grain.In the core of the grains small platelets of augite about 0.02μm thick have farmed parallel to the (001) plane (Fig. 1). These are thought to have exsolved by homogeneous nucleation. Subsequently the inversion of the pigeonite has led to the creation of APB's.

Sign in / Sign up

Export Citation Format

Share Document