scholarly journals The influence of fuel injection and heat release on bulk flow structures in a direct-injection, swirl-supported diesel engine

2007 ◽  
Vol 43 (2-3) ◽  
pp. 273-283 ◽  
Author(s):  
Paul C. Miles ◽  
Leif Hildingsson ◽  
Anders Hultqvist
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Fuel Injection ◽  
Direct Injection ◽  
Bulk Flow ◽  
Flow Structures

scholarly journals The Effect of RME-1-Butanol Blends on Combustion, Performance and Emission of a Direct Injection Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2941
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Specific Energy Consumption ◽  
Combustion Process ◽  
Constant Load ◽  
Combustion Stability ◽  
Performance And Emission ◽  
Energy Share ◽  
The Stability

The main objective of this study was assessment of the performance, emissions and combustion characteristics of a diesel engine using RME–1-butanol blends. In assessing the combustion process, great importance was placed on evaluating the stability of this process. Not only were the typical COVIMEP indicators assessed, but also the non-burnability of the characteristic combustion stages: ignition delay, time of 50% heat release and the end of combustion. The evaluation of the combustion process based on the analysis of heat release. The tests carried out on a 1-cylinder diesel engine operating at a constant load. Research and evaluation of the combustion process of a mixture of RME and 1-butanol carried out for the entire range of shares of both fuels up to 90% of 1-butanol energetic fraction. The participation of butanol in combustion process with RME increased the in-cylinder peak pressure and the heat release rate. With the increase in the share of butanol there was noted a decrease in specific energy consumption and an increase in engine efficiency. The share of butanol improved the combustion stability. There was also an increase in NOx emissions and decrease in CO and soot emissions. The engine can be power by blend up to 80% energy share of butanol.

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

scholarly journals On the possibility to decrease the fuel consumption for a heavy-duty truck Diesel engine using the Turbo-compound method: a case study

2019 ◽  
Vol 290 ◽  
pp. 06008
Author(s):  
Bogdan Radu ◽  
Alexandru Racovitza
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Large Data ◽  
Gas Emissions ◽  
Main Research ◽  
Injection Methods ◽  
Calculation System ◽  
Release Characteristic

The reduction of Diesel internal combustion engines emissions is one of the major concerns of the engines manufacturers. Despite the fact that the efficiency of the gas post-treatment systems has been significantly improved, decreasing the smoke and the soot from the cylinder inside remains a main research goal. This work is proposing a theoretical study on these pollutants formation for different kinds of direct injection methods. By dividing the in-cylinder injection the heat release characteristic could be modified, leading to different temperature and pressure levels. Using exhaust gas recirculation (EGR) the reduction of the gas temperatures might also be decreased, limiting NOx formation. To evaluate the level of the cylinder gas emissions formation a two-step procedure could be followed. First, by using a numerical calculation system the heat release characteristic can be highlighted concerning a Diesel engine with stratified injection; then, using an experimental relationship applying a large data base, the amount of the gas emissions can be subsequently provided. The authors propose some combinations between injection characteristics and EGR used fractions which could generate successfully results speaking in terms of NOx, soot and smoke formation.

Multi-Valve High-Speed Direct Injection Diesel Engines—the Design Challenge

1993 ◽  
Vol 207 (4) ◽  
pp. 307-315
Author(s):  
I P Gilbert ◽  
A R Heath ◽  
I D Johnstone
Keyword(s):  
Diesel Engine ◽  
Fuel Economy ◽  
Cylinder Head ◽  
High Speed ◽  
Fuel Injection ◽  
Direct Injection ◽  
Selection Strategy ◽  
Design Challenge ◽  
Hsdi Diesel Engine ◽  
High Level

The need to increase power, to improve fuel economy and to meet stringent exhaust emissions legislation with a high level of refinement has provided a challenge for the design of a compact high-speed direct injection (HSDI) diesel engine. This paper describes various aspects of cylinder head design with particular consideration of layout and number of valves, valve actuation, port selection strategy, fuel injection systems and cylinder head construction.

Effect of Fuel Injection Timing Relative to Ignition Timing on the Natural-Gas Direct-Injection Combustion

2001 ◽  
Author(s):  
Zuohua Huang ◽  
Seiichi Shiga ◽  
Takamasa Ueda ◽  
Nobuhisa Jingu ◽  
Hisao Nakamura ◽  
...  
Keyword(s):  
Heat Release ◽  
Late Stage ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Wide Range

Abstract Effect of fuel injection timing relative to ignition timing on natural gas direct-injection combustion was studied by using a rapid compression machine. The ignition timing was fixed at 80 ms from the compression start. When the injection timing was relatively earlier (injection start at 60 ms), the heat release pattern showed slower burn in the initial stage and faster burn in the late stage, which is similar to that of flame propagation of a premixed gas. In contrast to this, when the injection timing was relatively later (injection start at 75 ms), the heat release rate showed faster burn in the initial stage and slower burn in the late stage, which is similar to that of diesel combustion. The shortest duration was realized at the injection end timing of 80 ms (the same timing as the ignition timing) over the wide range of equivalence ratio. The degree of charge stratification and the intensity of turbulence generated by the fuel jet is considered to cause these behaviors. Earlier injection leads to longer duration of the initial combustion, whereas the later injection does longer duration of the late combustion. Earlier injection showed relatively lower CO emission while later injection produces relatively lower NOx emission. It was suggested that earlier injection leads to lower mixture stratification combustion and later injection leads to higher mixture stratification combustion. Combustion efficiency maintained high value over the wide range of equivalence ratio.

Evaluation of the combustion-induced noise and vibration using coherence and wavelet coherence estimates in a diesel engine

2019 ◽  
pp. 146808741987854
Author(s):  
Hossein Ahmadian ◽  
Gholamhassan Najafi ◽  
Barat Ghobadian ◽  
Seyed Reza Hassan-Beygi ◽  
Seyed Salar Hoseini
Keyword(s):  
Diesel Engine ◽  
Sound Pressure ◽  
Fuel Injection ◽  
Direct Injection ◽  
Wavelet Coherence ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Noise And Vibration ◽  
Four Levels ◽  
Wavelet Coherency

The understanding of noise generation and source identification is vital in noise control. This research was conducted to experimentally evaluate combustion-induced noise and vibration using coherence and wavelet coherence estimates. A single-cylinder direct-injection diesel engine was chosen for experimental investigation. The independent variables for conducting experiments were injection timing with five levels of 22, 27, 32 (normal), 37, and 42 crank angles before the top dead center, and also the engine torque load with four levels of 55%, 70%, 85%, and 100% of the rated value. The signals of cylinder pressure, liner acceleration, and radiated sound pressure of the test engine were measured and recorded. Then, coherency and wavelet coherency experiments were carried out between cylinder pressure and liner acceleration, cylinder pressure and sound pressure, and liner acceleration and sound pressure signals in MATLAB software. The results indicated that increasing load would increase wavelet coherency between cylinder pressure and liner acceleration signals at frequencies higher than 1 kHz. The coherent regions between cylinder pressure and sound pressure signals were mainly at frequencies higher than 1 kHz while advancing the fuel injection timing had shifted the coherency toward lower frequencies. In general, with advancing injection timing, the coherent regions between liner acceleration and sound pressure signals have appeared at broader time ranges, especially at frequencies between 100 and 500 Hz. Comparing the results of the wavelet coherency and coherency tests, we concluded that wavelet coherency is a more accurate and descriptive tool in evaluating the combustion-induced noise and vibration.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

Sign in / Sign up

Export Citation Format

Share Document