The effect of ‘material ratchetting’ on the incremental growth of beams subjected to steady axial loads and cyclic bending

1985 ◽  
Vol 27 (4) ◽  
pp. 207-223 ◽  
Author(s):  
T.H. Hyde ◽  
B.B. Sahari ◽  
J.J. Webster
Author(s):  
Y.P. Manshin ◽  
◽  
E.Yu. Manshina ◽  

The article considers an algorithm for analyzing the results of field strain-measurement studies of machine structures, which allows obtaining data for the modernization of elements in the form of coefficients of parameter changes. As the object of application of the method, the design element of the header was selected, which had failures due to insufficient endurance under cyclic bending stresses.


AIAA Journal ◽  
10.2514/1.781 ◽  
2003 ◽  
Vol 41 (11) ◽  
Author(s):  
Christos Kassapoglou ◽  
William A. Townsend

Author(s):  
Byoung-Joon Kim ◽  
Hae-A-Seul Shin ◽  
In-Suk Choi ◽  
Young-Chang Joo

Abstract The electrical resistance Cu film on flexible substrate was investigated in cyclic bending deformation. The electrical resistance of 1 µm thick Cu film on flexible substrate increased up to 120 % after 500,000 cycles in 1.1 % tensile bending strain. Crack and extrusion were observed due to the fatigue damage of metal film. Low bending strain did not cause any damage on metal film but higher bending strain resulted in severe electrical and mechanical damage. Thinner film showed higher fatigue resistance because of the better mechanical property of thin film. Cu film with NiCr under-layer showed poorer fatigue resistance in tensile bending mode. Ni capping layer did not improve the fatigue resistance of Cu film, but Al capping layer suppressed crack formation and lowered electrical resistance change. The NiCr under layer, Ni capping layer, and Al capping layer effect on electrical resistance change of Cu film was compared with Cu only sample.


Author(s):  
Nadine Nagler ◽  
Armin Lohrengel

AbstractOverrunning clutches, also known as freewheel clutches, are frictionally engaged, directional clutches; they transmit torque depending on the Freewheel clutch rings’ rotation directions. The torque causes a tangential force in the Hertzian contact area. The hitherto “state-of-the-art design criterion” bases on this load situation. In practice, axial loads additionally act on the frictionally engaged Hertzian contact area. This additional axial load can cause the loss of the friction connection and so the freewheel clutch slips. This publication presents an improved design criterion for frictionally engaged contacts in freewheel clutches. It allows to consider tangential as well as axial loads during the design process. Additionally, it offers the possibility to estimate the probability of frictional engagement loss and gross slip based on the freewheel clutch’s application scenario. This publication points out how to use the improved design criterion to design freewheel clutches that are more robust against a loss of function.


Forests ◽  
2020 ◽  
Vol 12 (1) ◽  
pp. 29
Author(s):  
Anna Cedro ◽  
Bernard Cedro

Intermediate hawthorn (Crataegus × media Bechst.) is broadly distributed in Europe but very rarely examined by dendrochronologists. In NW Poland, it is one of three naturally occurring hawthorn species, growing mainly at forest margins, along roads, in mid-field woodlots, and on uncultivated land. Biocenotically, it is a very valuable species. This study aimed to determine the age of trees, tree-ring dynamics, and growth–climate relationship for intermediate hawthorn. Signature years were also determined. Samples for analysis were collected from 22 trees growing in a typical agricultural landscape in a monospecific mid-field woodlot comprised of several hundred specimens of various ages and forms (shrubs and trees). Using classic methods of dendrochronological dating, a 40-year long chronology spanning 1981–2020 was constructed. The radial growth rate of intermediate hawthorn is comparable to other tree species forming stands in NW Poland and equals 2.41 mm/year. Considerable intersubject variability is noted, from 1.48 to 4.44 mm/year. The chronology was also used for dendroclimatological analyses, including correlation and response function and signature years. Of the meteorological parameters analyzed, annual incremental growth in hawthorn is the most strongly shaped by precipitation totals from May to August of the current vegetation year: high rainfall favors the formation of wide tree-rings. Statistically significant growth–climate relationships were also obtained for winter months (December of the preceding vegetation year, January and February), for which period negative correlation and regression values are noted for air temperature and insolation. Furthermore, high precipitation, low-temperature and low insolation late in the preceding vegetation year (especially in August) make a positive influence on the condition of trees in the upcoming growing season. Signature year analysis clearly pointed to precipitation as the dominant factor in shaping tree-rings in the studied hawthorn population. As there are no dendrochronological papers concerning indigenous hawthorn species, future studies should be expanded to include diverse geographic locations and habitat conditions and should include all three species of hawthorn occurring in Poland.


Author(s):  
Ming Zhang ◽  
Yanyao Jiang ◽  
Chu-Hwa Lee

A three-dimensional finite element (FE) model with the consideration of the helix angle of the threads was developed to simulate the second stage self-loosening of a bolted joint. The second stage self-loosening refers to the graduate reduction in clamping force due to the back-off of the nut. The simulations were conducted for two plates jointed by a bolt and a nut and the joint was subjected to transverse or shear loading. An M12×1.75 bolt was used. The application of the preload was simulated by using an orthogonal temperature expansion method. FE simulations were conducted for several loading conditions with different preloads and relative displacements between the two clamped plates. It was found that due to the application of the cyclic transverse load, micro-slip occurred between the contacting surfaces of the engaged threads of the bolt and the nut. In addition, a cyclic bending moment was introduced on the bolted joint. The cyclic bending moment resulted in an oscillation of the contact pressure on the contacting surfaces of the engaged threads. The micro-slip between the engaged threads and the variation of the contact pressure were identified to be the major mechanisms responsible for the self-loosening of a bolted joint. Simplified finite element models were developed that confirmed the mechanisms discovered. The major self-loosening behavior of a bolted joint can be properly reproduced with the FE model developed. The results obtained agree quantitatively with the experimental observations.


Sign in / Sign up

Export Citation Format

Share Document