Numerical investigation of the effects of system volume and average mass flow on the surge characteristics of an axial compressor

2020 ◽  
Vol 106 ◽  
pp. 106172
Author(s):  
Meng Wang ◽  
Haiou Sun ◽  
Zhongyi Wang ◽  
Yanhua Wang ◽  
Franco Magagnato ◽  
...  
Keyword(s):  
Numerical Investigation ◽  
Mass Flow ◽  
Axial Compressor ◽  
Average Mass ◽  
System Volume

Numerical Simulation of the Performance of an Axial Compressor Operating With Supercritical Carbon Dioxide

2018 ◽  
Author(s):  
Jinlan Gou ◽  
Wei Wang ◽  
Can Ma ◽  
Yong Li ◽  
Yuansheng Lin ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Numerical Simulation ◽  
Supercritical Carbon Dioxide ◽  
Critical Point ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Brayton Cycle ◽  
Supercritical Carbon

Using supercritical carbon dioxide (SCO2) as the working fluid of a closed Brayton cycle gas turbine is widely recognized nowadays, because of its compact layout and high efficiency for modest turbine inlet temperature. It is an attractive option for geothermal, nuclear and solar energy conversion. Compressor is one of the key components for the supercritical carbon dioxide Brayton cycle. With established or developing small power supercritical carbon dioxide test loop, centrifugal compressor with small mass flow rate is mainly investigated and manufactured in the literature; however, nuclear energy conversion contains more power, and axial compressor is preferred to provide SCO2 compression with larger mass flow rate which is less studied in the literature. The performance of the axial supercritical carbon dioxide compressor is investigated in the current work. An axial supercritical carbon dioxide compressor with mass flow rate of 1000kg/s is designed. The thermodynamic region of the carbon dioxide is slightly above the vapor-liquid critical point with inlet total temperature 310K and total pressure 9MPa. Numerical simulation is then conducted to assess this axial compressor with look-up table adopted to handle the nonlinear variation property of supercritical carbon dioxide near the critical point. The results show that the performance of the design point of the designed axial compressor matches the primary target. Small corner separation occurs near the hub, and the flow motion of the tip leakage fluid is similar with the well-studied air compressor. Violent property variation near the critical point creates troubles for convergence near the stall condition, and the stall mechanism predictions are more difficult for the axial supercritical carbon dioxide compressor.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

scholarly journals Simulation Analysis on Water’s Micro Seepage Laws under Different Pressure Gradients Using Computed Tomography Method

2018 ◽  
Vol 2018 ◽  
pp. 1-26 ◽  
Author(s):  
Gang Zhou ◽  
Lei Qiu ◽  
Wenzheng Zhang ◽  
Jiao Xue
Keyword(s):  
Pressure Gradient ◽  
Mass Flow ◽  
Simulation Analysis ◽  
Effective Porosity ◽  
Pressure Gradients ◽  
Seepage Velocity ◽  
Average Mass ◽  
Depth Analysis ◽  
Tomography Method ◽  
Insight Into

The aim of this paper was to develop a model that can characterize the actual micropore structures in coal and gain an in-depth insight into water’s seepage rules in coal pores under different pressure gradients from a microscopic perspective. To achieve this goal, long-flame coals were first scanned by an X-ray 3D microscope; then, through a representative elementary volume (REV) analysis, the optimal side length was determined to be 60 μm; subsequently, by using Avizo software, the coal’s micropore structures were acquired. Considering that the porosity varies in the same coal sample, this study selected four regions in the sample for an in-depth analysis. Moreover, numerical simulations on water’s seepage behaviors in coal under 30 different pressure gradients were performed. The results show that (1) the variation of the simulated seepage velocity and pressure gradient accorded with Forchheimer’s high-velocity nonlinear seepage rules; (2) the permeability did not necessarily increase with the increase of the effective porosity; (3) in the same model, under different pressure gradients, the average seepage pressure decreased gradually, while the average seepage velocity and average mass flow varied greatly with the increase of the seepage length; and (4) under the same pressure gradient, the increase of the average mass flow from the inlet to the outlet became more significant under a higher inlet pressure.

Turbulence Model Influence on Numerical Investigation of Transonic Axial Compressor Rotor

2011 ◽  
Vol 308-310 ◽  
pp. 1519-1522
Author(s):  
Fang Xie ◽  
Chang Jiang Liu ◽  
You Jun Wang
Keyword(s):  
Experimental Data ◽  
Numerical Investigation ◽  
Turbulence Model ◽  
Characteristic Curve ◽  
Axial Compressor ◽  
Internal Flow ◽  
Turbulent Model ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
Point Forecast

Numerical method using HI and HOH meshing combined B - L turbulent model and S - A turbulent model separately based on the Rotor 37 compressor Rotor was applied to the steady flow. results on pressure characteristic curve, stall point forecast etc were compared with related experimental data. This paper discussed calculation precision influenced by the turbulence model and numerical computation grid. This numerical investigation was basis for subsequent compressor internal flow field study.

Performance of Strongly Bowed Stators in a Four-Stage High-Speed Compressor

2004 ◽  
Vol 126 (3) ◽  
pp. 333-338 ◽  
Author(s):  
Axel Fischer ◽  
Walter Riess ◽  
Joerg R. Seume
Keyword(s):  
Mass Flow ◽  
High Speed ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Controlled Diffusion ◽  
Stage 4 ◽  
The University

The FVV sponsored project “Bow Blading” (cf. acknowledgments) at the Turbomachinery Laboratory of the University of Hannover addresses the effect of strongly bowed stator vanes on the flow field in a four-stage high-speed axial compressor with controlled diffusion airfoil (CDA) blading. The compressor is equipped with more strongly bowed vanes than have previously been reported in the literature. The performance map of the present compressor is being investigated experimentally and numerically. The results show that the pressure ratio and the efficiency at the design point and at the choke limit are reduced by the increase in friction losses on the surface of the bowed vanes, whose surface area is greater than that of the reference (CDA) vanes. The mass flow at the choke limit decreases for the same reason. Because of the change in the radial distribution of axial velocity, pressure rise shifts from stage 3 to stage 4 between the choke limit and maximum pressure ratio. Beyond the point of maximum pressure ratio, this effect is not distinguishable from the reduction of separation by the bow of the vanes. Experimental results show that in cases of high aerodynamic loading, i.e., between maximum pressure ratio and the stall limit, separation is reduced in the bowed stator vanes so that the stagnation pressure ratio and efficiency are increased by the change to bowed stators. It is shown that the reduction of separation with bowed vanes leads to a increase of static pressure rise towards lower mass flow so that the present bow bladed compressor achieves higher static pressure ratios at the stall limit.

Micropump With Six Vibrating Membranes: Design Analysis

2008 ◽  
Author(s):  
Kittisak Koombua ◽  
Ramana M. Pidaparti ◽  
P. Worth Longest ◽  
Gary M. Atkinson
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Pressure Head ◽  
Maximum Pressure ◽  
Operating Cycle ◽  
Average Mass ◽  
Volume Method ◽  
Novel Design ◽  
Membrane Displacement

In this study, a novel design of multiple vibrating membrane micropump has been investigated. The micropump is composed of six membranes and three nozzle/diffuser elements. The membranes were vibrated out-of-phase simultaneously to create pressure difference in the pump chamber. The characteristics of this micropump were analyzed using the finite volume method. The commercial computational fluid dynamics software, FLUENT, with the dynamic mesh algorithm was employed to study velocity field and flow rate during the operating cycle. The simulation results showed that the movement of these membranes combined with the rectification behavior of three nozzle/diffuser elements can minimize back flow and improve net flow in one direction. The average mass flow rate from the micropump increased when the maximum membrane displacement and membrane frequency increased. However, the average mass flow rate from the micropump decreased when pressure head increased. Increases in maximum pressure head were associated with increases in membrane frequency.

Numerical Simulation of Effects of Tip Geometry on the Performance of an Axial Compressor

2012 ◽  
Author(s):  
Hongwei Ma ◽  
Jun Zhang
Keyword(s):  
Mass Flow ◽  
Tangential Force ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Leading Edge ◽  
Suction Side ◽  
Leakage Flow ◽  
Base Line ◽  
Compressor Rotor ◽  
Blade Tip

The purpose of this paper is to investigate numerically the effects of the tip geometry on the performance of an axial compressor rotor. There are three case studies which are compared with the base line tip geometry. 1) baseline (flat tip); 2) Cavity (tip with a cavity); 3) SSQA (suction side squealer tip) and 4) SSQB (modified suction side squealer tip). The case of SSQB is a combination of suction side squealer tip and the cavity tip. From leading edge to 10% chord, the tip has a cavity. From 10% chord to trailing edge, the tip has a suction side squealer. The numerical results of 2) show that the cavity tip leads to lower leakage mass flow and greater loss in tip gap and the rotor passage. The loading near the blade tip is lower than the baseline, thus the tangential force of the blade is lower. It leads to lower pressure rise than the baseline. The performance of the compressor for the tip with cavity is worse than the baseline. The results of 3) show that the higher curvature of the suction side squealer increases the loading of the blade and the tangential blade force. With the suction side squealer tip, the leakage flow experiences two vena contractor thus the mass of the leakage flow is reduced which is benefit for the performance of the compressor. The loss in the tip gap is lower than baseline. The performance is better than the baseline with greater pressure rise of the rotor, smaller leakage mass flow and lower averaged loss. For the case the SSQB, the leakage mass flow is lower than the SSQA and the loss in the tip gap and the rotor passage is greater than SSQA. The performance of the case of the SSQB is worse than the case of SSQA.

Stall Inception and Development Process Due to Tip Leakage Flow in Axial Compressor Rotor Blades Row

2014 ◽  
Vol 30 (3) ◽  
pp. 307-313 ◽  
Author(s):  
R. Taghavi-Zenou ◽  
S. Abbasi ◽  
S. Eslami
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Leading Edge ◽  
Rotor Blades ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

ABSTRACTThis paper deals with tip leakage flow structure in subsonic axial compressor rotor blades row under different operating conditions. Analyses are based on flow simulation utilizing computational fluid dynamic technique. Three different circumstances at near stall condition are considered in this respect. Tip leakage flow frequency spectrum was studied through surveying instantaneous static pressure signals imposed on blades surfaces. Results at the highest flow rate, close to the stall condition, showed that the tip vortex flow fluctuates with a frequency close to the blade passing frequency. In addition, pressure signals remained unchanged with time. Moreover, equal pressure fluctuations at different passages guaranteed no peripheral disturbances. Tip leakage flow frequency decreased with reduction of the mass flow rate and its structure was changing with time. Spillage of the tip leakage flow from the blade leading edge occurred without any backflow in the trailing edge region. Consequently, various flow structures were observed within every passage between two adjacent blades. Further decrease in the mass flow rate provided conditions where the spilled flow ahead of the blade leading edge together with trailing edge backflow caused spike stall to occur. This latter phenomenon was accompanied by lower frequencies and higher amplitudes of the pressure signals. Further revolution of the rotor blade row caused the spike stall to eventuate to larger stall cells, which may be led to fully developed rotating stall.

Sign in / Sign up

Export Citation Format

Share Document